Reduce rgb matrix firmware size

Corrected formatting and added shortcuts.

Removed invalid #define

docs/config_options.md

@@ -171,6 +171,8 @@ If you define these options you will enable the associated feature, which may in
   * how long for the Combo keys to be detected. Defaults to `TAPPING_TERM` if not defined.
 * `#define TAP_CODE_DELAY 100`
   * Sets the delay between `register_code` and `unregister_code`, if you're having issues with it registering properly (common on VUSB boards). The value is in milliseconds.
+* `#define TAP_HOLD_CAPS_DELAY 200`
+  * Sets the delay for Tap Hold keys (`LT`, `MT`) when using `KC_CAPSLOCK` keycode, as this has some special handling on MacOS.  The value is in milliseconds, and defaults to 200ms if not defined. 
 
 ## RGB Light Configuration
 

docs/feature_audio.md

@@ -175,8 +175,9 @@ You can configure the default, min and max frequencies, the stepping and built i
 | `AUDIO_CLICKY_FREQ_DEFAULT` | 440.0f | Sets the default/starting audio frequency for the clicky sounds. |
 | `AUDIO_CLICKY_FREQ_MIN` | 65.0f | Sets the lowest frequency (under 60f are a bit buggy). |
 | `AUDIO_CLICKY_FREQ_MAX` | 1500.0f | Sets the the highest frequency. Too high may result in coworkers attacking you. |
-| `AUDIO_CLICKY_FREQ_FACTOR` | 1.18921f| Sets the stepping of UP/DOWN key codes. |
+| `AUDIO_CLICKY_FREQ_FACTOR` | 1.18921f| Sets the stepping of UP/DOWN key codes.  This is a multiplicative factor.  The default steps the frequency up/down by a musical minor third.  |
 | `AUDIO_CLICKY_FREQ_RANDOMNESS`     |  0.05f |  Sets a factor of randomness for the clicks, Setting this to `0f` will make each click identical, and `1.0f` will make this sound much like the 90's computer screen scrolling/typing effect. | 
+| `AUDIO_CLICKY_DELAY_DURATION` | 1 | An integer note duration where 1 is 1/16th of the tempo, or a sixty-fourth note (see `quantum/audio/musical_notes.h` for implementation details). The main clicky effect will be delayed by this duration.  Adjusting this to values around 6-12 will help compensate for loud switches. |
 
 
 

docs/feature_rgb_matrix.md

@@ -144,14 +144,16 @@ const led_config_t g_led_config = { {
 } };
 ```
 
-The first part, `// Key Matrix to LED Index`, tells the system what key this LED represents by using the key's electrical matrix row & col. The second part, `// LED Index to Physical Position` represents the LED's physical position on the keyboard. The first value, `x`, is between 0-224 (inclusive), and the second value, `y`, is between 0-64 (inclusive). This range is due to effect that calculate the center or halves for their animations. The easiest way to calculate these positions is imagine your keyboard is a grid, and the top left of the keyboard represents x, y coordinate 0, 0 and the bottom right of your keyboard represents 224, 64. Using this as a basis, you can use the following formula to calculate the physical position:
+The first part, `// Key Matrix to LED Index`, tells the system what key this LED represents by using the key's electrical matrix row & col. The second part, `// LED Index to Physical Position` represents the LED's physical `{ x, y }` position on the keyboard. The default expected range of values for `{ x, y }` is the inclusive range `{ 0..224, 0..64 }`. This default expected range is due to effects that calculate the center of the keyboard for their animations. The easiest way to calculate these positions is imagine your keyboard is a grid, and the top left of the keyboard represents `{ x, y }` coordinate `{ 0, 0 }` and the bottom right of your keyboard represents `{ 224, 64 }`. Using this as a basis, you can use the following formula to calculate the physical position:
 
 ```C
 x = 224 / (NUMBER_OF_COLS - 1) * COL_POSITION
 y =  64 / (NUMBER_OF_ROWS - 1) * ROW_POSITION
 ```
 
-Where NUMBER_OF_COLS, NUMBER_OF_ROWS, COL_POSITION, & ROW_POSITION are all based on the physical layout of your keyboard, not the electrical layout.
+Where NUMBER_OF_COLS, NUMBER_OF_ROWS, COL_POSITION, & ROW_POSITION are all based on the physical layout of your keyboard, not the electrical layout. 
+
+As mentioned earlier, the center of the keyboard by default is expected to be `{ 112, 32 }`, but this can be changed if you want to more accurately calculate the LED's physical `{ x, y }` positions. Keyboard designers can implement `#define RGB_MATRIX_CENTER { 112, 32 }` in their config.h file with the new center point of the keyboard, or where they want it to be allowing more possibilities for the `{ x, y }` values. Do note that the maximum value for x or y is 255, and the recommended maximum is 224 as this gives animations runoff room before they reset.
 
 `// LED Index to Flag` is a bitmask, whether or not a certain LEDs is of a certain type. It is recommended that LEDs are set to only 1 type.
 
@@ -194,12 +196,20 @@ enum rgb_matrix_effects {
     RGB_MATRIX_ALPHAS_MODS,         // Static dual hue, speed is hue for secondary hue
     RGB_MATRIX_GRADIENT_UP_DOWN,    // Static gradient top to bottom, speed controls how much gradient changes
     RGB_MATRIX_BREATHING,           // Single hue brightness cycling animation
+    RGB_MATRIX_BAND_SAT,        // Single hue band fading saturation scrolling left to right
+    RGB_MATRIX_BAND_VAL,        // Single hue band fading brightness scrolling left to right
+    RGB_MATRIX_BAND_PINWHEEL_SAT,   // Single hue 3 blade spinning pinwheel fades saturation
+    RGB_MATRIX_BAND_PINWHEEL_VAL,   // Single hue 3 blade spinning pinwheel fades brightness
+    RGB_MATRIX_BAND_SPIRAL_SAT,     // Single hue spinning spiral fades saturation
+    RGB_MATRIX_BAND_SPIRAL_VAL,     // Single hue spinning spiral fades brightness
     RGB_MATRIX_CYCLE_ALL,           // Full keyboard solid hue cycling through full gradient
     RGB_MATRIX_CYCLE_LEFT_RIGHT,    // Full gradient scrolling left to right
     RGB_MATRIX_CYCLE_UP_DOWN,       // Full gradient scrolling top to bottom
     RGB_MATRIX_CYCLE_OUT_IN,        // Full gradient scrolling out to in
     RGB_MATRIX_CYCLE_OUT_IN_DUAL,   // Full dual gradients scrolling out to in
     RGB_MATRIX_RAINBOW_MOVING_CHEVRON,  // Full gradent Chevron shapped scrolling left to right
+    RGB_MATRIX_CYCLE_PINWHEEL,      // Full gradient spinning pinwheel around center of keyboard
+    RGB_MATRIX_CYCLE_SPIRAL,        // Full gradient spinning spiral around center of keyboard
     RGB_MATRIX_DUAL_BEACON,         // Full gradient spinning around center of keyboard
     RGB_MATRIX_RAINBOW_BEACON,      // Full tighter gradient spinning around center of keyboard
     RGB_MATRIX_RAINBOW_PINWHEELS,   // Full dual gradients spinning two halfs of keyboard
@@ -235,6 +245,12 @@ You can disable a single effect by defining `DISABLE_[EFFECT_NAME]` in your `con
 |`#define DISABLE_RGB_MATRIX_ALPHAS_MODS`               |Disables `RGB_MATRIX_ALPHAS_MODS`              |
 |`#define DISABLE_RGB_MATRIX_GRADIENT_UP_DOWN`          |Disables `RGB_MATRIX_GRADIENT_UP_DOWN`         |
 |`#define DISABLE_RGB_MATRIX_BREATHING`                 |Disables `RGB_MATRIX_BREATHING`                |
+|`#define DISABLE_RGB_MATRIX_BAND_SAT`                  |Disables `RGB_MATRIX_BAND_SAT`                 |
+|`#define DISABLE_RGB_MATRIX_BAND_VAL`                  |Disables `RGB_MATRIX_BAND_VAL`                 |
+|`#define DISABLE_RGB_MATRIX_BAND_PINWHEEL_SAT`         |Disables `RGB_MATRIX_BAND_PINWHEEL_SAT`        |
+|`#define DISABLE_RGB_MATRIX_BAND_PINWHEEL_VAL`         |Disables `RGB_MATRIX_BAND_PINWHEEL_VAL`        |
+|`#define DISABLE_RGB_MATRIX_BAND_SPIRAL_SAT`           |Disables `RGB_MATRIX_BAND_SPIRAL_SAT`          |
+|`#define DISABLE_RGB_MATRIX_BAND_SPIRAL_VAL`           |Disables `RGB_MATRIX_BAND_SPIRAL_VAL`          |
 |`#define DISABLE_RGB_MATRIX_CYCLE_ALL`                 |Disables `RGB_MATRIX_CYCLE_ALL`                |
 |`#define DISABLE_RGB_MATRIX_CYCLE_LEFT_RIGHT`          |Disables `RGB_MATRIX_CYCLE_LEFT_RIGHT`         |
 |`#define DISABLE_RGB_MATRIX_CYCLE_UP_DOWN`             |Disables `RGB_MATRIX_CYCLE_UP_DOWN`            |
@@ -242,6 +258,8 @@ You can disable a single effect by defining `DISABLE_[EFFECT_NAME]` in your `con
 |`#define DISABLE_RGB_MATRIX_CYCLE_OUT_IN_DUAL`         |Disables `RGB_MATRIX_CYCLE_OUT_IN_DUAL`        |
 |`#define DISABLE_RGB_MATRIX_RAINBOW_MOVING_CHEVRON`    |Disables `RGB_MATRIX_RAINBOW_MOVING_CHEVRON`   |
 |`#define DISABLE_RGB_MATRIX_DUAL_BEACON`               |Disables `RGB_MATRIX_DUAL_BEACON`              |
+|`#define DISABLE_RGB_MATRIX_CYCLE_PINWHEEL`            |Disables `RGB_MATRIX_CYCLE_PINWHEEL`           |
+|`#define DISABLE_RGB_MATRIX_CYCLE_SPIRAL`              |Disables `RGB_MATRIX_CYCLE_SPIRAL`             |
 |`#define DISABLE_RGB_MATRIX_RAINBOW_BEACON`            |Disables `RGB_MATRIX_RAINBOW_BEACON`           |
 |`#define DISABLE_RGB_MATRIX_RAINBOW_PINWHEELS`         |Disables `RGB_MATRIX_RAINBOW_PINWHEELS`        |
 |`#define DISABLE_RGB_MATRIX_RAINDROPS`                 |Disables `RGB_MATRIX_RAINDROPS`                |

docs/feature_rgblight.md

@@ -129,7 +129,7 @@ The following options are used to tweak the various animations:
 |`RGBLIGHT_EFFECT_KNIGHT_LED_NUM`    |`RGBLED_NUM` |The number of LEDs to have the "Knight" animation travel                             |
 |`RGBLIGHT_EFFECT_KNIGHT_LENGTH`     |`3`          |The number of LEDs to light up for the "Knight" animation                            |
 |`RGBLIGHT_EFFECT_KNIGHT_OFFSET`     |`0`          |The number of LEDs to start the "Knight" animation from the start of the strip by    |
-|`RGBLIGHT_RAINBOW_SWIRL_RANGE`      |`360`        |Range adjustment for the rainbow swirl effect to get different swirls                |
+|`RGBLIGHT_RAINBOW_SWIRL_RANGE`      |`255`        |Range adjustment for the rainbow swirl effect to get different swirls                |
 |`RGBLIGHT_EFFECT_SNAKE_LENGTH`      |`4`          |The number of LEDs to light up for the "Snake" animation                             |
 
 ### Example Usage to Reduce Memory Footprint
@@ -176,44 +176,100 @@ const uint8_t RGBLED_GRADIENT_RANGES[] PROGMEM = {255, 170, 127, 85, 64};
 
 If you need to change your RGB lighting in code, for example in a macro to change the color whenever you switch layers, QMK provides a set of functions to assist you. See [`rgblight.h`](https://github.com/qmk/qmk_firmware/blob/master/quantum/rgblight.h) for the full list, but the most commonly used functions include:
 
-|Function                                    |Description                                                                                                                                                   |
-|--------------------------------------------|--------------------------------------------------------------------------------------------------------------------------------------------------------------|
-|`rgblight_enable()`                         |Turn LEDs on, based on their previous state                                                                                                                   |
-|`rgblight_enable_noeeprom()`                |Turn LEDs on, based on their previous state (not written to EEPROM)                                                                                           |
-|`rgblight_disable()`                        |Turn LEDs off                                                                                                                                                 |
-|`rgblight_disable_noeeprom()`               |Turn LEDs off (not written to EEPROM)                                                                                                                         |
-|`rgblight_mode(x)`                          |Set the mode, if RGB animations are enabled                                                                                                                   |
-|`rgblight_mode_noeeprom(x)`                 |Set the mode, if RGB animations are enabled (not written to EEPROM)                                                                                           |
-|`rgblight_setrgb(r, g, b)`                  |Set all LEDs to the given RGB value where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM)                                                           |
-|`rgblight_setrgb_at(r, g, b, led)`          |Set a single LED to the given RGB value, where `r`/`g`/`b` are between 0 and 255 and `led` is between 0 and `RGBLED_NUM` (not written to EEPROM)              |
+### Utility Functions
+|Function                                    |Description                                                        |
+|--------------------------------------------|-------------------------------------------------------------------|
+|`sethsv(hue, sat, val, ledbuf)`             |Set ledbuf to the given HSV value                                  |
+|`sethsv_raw(hue, sat, val, ledbuf)`         |Set ledbuf to the given HSV value without RGBLIGHT_LIMIT_VAL check |
+|`setrgb(r, g, b, ledbuf)`                   |Set ledbuf to the given RGB value where `r`/`g`/`b`                |
+
+### Low level Functions
+|Function                                    |Description                                |
+|--------------------------------------------|-------------------------------------------|
+|`rgblight_set()`                            |Flash out led buffers to LEDs              |
+|`rgblight_set_clipping_range(pos, num)`     |Set clipping Range. see [Clipping Range](#clipping-range) |
+
+Example:
+```c
+sethsv(HSV_WHITE, (LED_TYPE *)&led[0]); // led 0
+sethsv(HSV_RED,   (LED_TYPE *)&led[1]); // led 1
+sethsv(HSV_GREEN, (LED_TYPE *)&led[2]); // led 2
+rgblight_set(); // Utility functions do not call rgblight_set() automatically, so they need to be called explicitly.
+```
+
+### Effects and Animations Functions
+#### effect range setting
+|Function                                    |Description       |
+|--------------------------------------------|------------------|
+|`rgblight_set_effect_range(pos, num)`       |Set Effects Range |
+
+#### direct operation
+|Function                                    |Description  |
+|--------------------------------------------|-------------|
+|`rgblight_setrgb_at(r, g, b, index)`          |Set a single LED to the given RGB value, where `r`/`g`/`b` are between 0 and 255 and `index` is between 0 and `RGBLED_NUM` (not written to EEPROM) |
+|`rgblight_sethsv_at(h, s, v, index)`          |Set a single LED to the given HSV value, where `h`/`s`/`v` are between 0 and 255, and `index` is between 0 and `RGBLED_NUM` (not written to EEPROM) |
 |`rgblight_setrgb_range(r, g, b, start, end)`|Set a continuous range of LEDs to the given RGB value, where `r`/`g`/`b` are between 0 and 255 and `start`(included) and `stop`(excluded) are between 0 and `RGBLED_NUM` (not written to EEPROM)|
-|`rgblight_setrgb_master(r, g, b)`           |Set the LEDs on the master side  to the given RGB value, where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM)                                      |
-|`rgblight_setrgb_slave(r, g, b)`            |Set the LEDs on the slave side  to the given RGB value, where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM)                                       |
-|`rgblight_sethsv(h, s, v)`                  |Set all LEDs to the given HSV value where `h` is between 0 and 360 and `s`/`v` are between 0 and 255                                                          |
-|`rgblight_sethsv_noeeprom(h, s, v)`         |Set all LEDs to the given HSV value where `h` is between 0 and 360 and `s`/`v` are between 0 and 255 (not written to EEPROM)                                  |
-|`rgblight_sethsv_at(h, s, v, led)`          |Set a single LED to the given HSV value, where `h` is between 0 and 360, `s`/`v` are between 0 and 255, and `led` is between 0 and `RGBLED_NUM` (not written to EEPROM)|
-|`rgblight_sethsv_range(h, s, v, start, end)`|Set a continuous range of LEDs to the given HSV value, where `h` is between 0 and 360, `s`/`v` are between 0 and 255, and `start`(included) and `stop`(excluded) are between 0 and `RGBLED_NUM` (not written to EEPROM)|
-|`rgblight_sethsv_master(h, s, v)`           |Set the LEDs on the master side to the given HSV value, where `h` is between 0 and 360, `s`/`v` are between 0 and 255 (not written to EEPROM)                 |
-|`rgblight_sethsv_slave(h, s, v)`            |Set the LEDs on the slave side to the given HSV value, where `h` is between 0 and 360, `s`/`v` are between 0 and 255 (not written to EEPROM)                  |
-|`rgblight_toggle()`                         |Toggle all LEDs between on and off                                                                                                                            |
-|`rgblight_toggle_noeeprom()`                |Toggle all LEDs between on and off (not written to EEPROM)                                                                                                    |
-|`rgblight_step()`                           |Change the mode to the next RGB animation in the list of enabled RGB animations                                                                               |
-|`rgblight_step_noeeprom()`                  |Change the mode to the next RGB animation in the list of enabled RGB animations (not written to EEPROM)                                                       |
-|`rgblight_step_reverse()`                   |Change the mode to the previous RGB animation in the list of enabled RGB animations                                                                           |
-|`rgblight_step_reverse_noeeprom()`          |Change the mode to the previous RGB animation in the list of enabled RGB animations (not written to EEPROM)                                                   |
-|`rgblight_increase_hue()`                   |Increase the hue for all LEDs. This wraps around at maximum hue                                                                                               |
-|`rgblight_increase_hue_noeeprom()`          |Increase the hue for all LEDs. This wraps around at maximum hue (not written to EEPROM)                                                                       |
-|`rgblight_decrease_hue()`                   |Decrease the hue for all LEDs. This wraps around at minimum hue                                                                                               |
-|`rgblight_decrease_hue_noeeprom()`          |Decrease the hue for all LEDs. This wraps around at minimum hue (not written to EEPROM)                                                                       |
-|`rgblight_increase_sat()`                   |Increase the saturation for all LEDs. This wraps around at maximum saturation                                                                                 |
-|`rgblight_increase_sat_noeeprom()`          |Increase the saturation for all LEDs. This wraps around at maximum saturation (not written to EEPROM)                                                         |
-|`rgblight_decrease_sat()`                   |Decrease the saturation for all LEDs. This wraps around at minimum saturation                                                                                 |
-|`rgblight_decrease_sat_noeeprom()`          |Decrease the saturation for all LEDs. This wraps around at minimum saturation (not written to EEPROM)                                                         |
-|`rgblight_increase_val()`                   |Increase the value for all LEDs. This wraps around at maximum value                                                                                           |
-|`rgblight_increase_val_noeeprom()`          |Increase the value for all LEDs. This wraps around at maximum value (not written to EEPROM)                                                                   |
-|`rgblight_decrease_val()`                   |Decrease the value for all LEDs. This wraps around at minimum value                                                                                           |
-|`rgblight_decrease_val_noeeprom()`          |Decrease the value for all LEDs. This wraps around at minimum value (not written to EEPROM)                                                                   |
-|`rgblight_set_clipping_range(pos, num)`     |Set clipping Range                                                                                                                                            |
+|`rgblight_sethsv_range(h, s, v, start, end)`|Set a continuous range of LEDs to the given HSV value, where `h`/`s`/`v` are between 0 and 255, and `start`(included) and `stop`(excluded) are between 0 and `RGBLED_NUM` (not written to EEPROM)|
+|`rgblight_setrgb(r, g, b)`                  |Set effect range LEDs to the given RGB value where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM) |
+|`rgblight_setrgb_master(r, g, b)`           |Set the LEDs on the master side  to the given RGB value, where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM) |
+|`rgblight_setrgb_slave(r, g, b)`            |Set the LEDs on the slave side  to the given RGB value, where `r`/`g`/`b` are between 0 and 255 (not written to EEPROM) |
+|`rgblight_sethsv_master(h, s, v)`           |Set the LEDs on the master side to the given HSV value, where `h`/`s`/`v` are between 0 and 255 (not written to EEPROM) |
+|`rgblight_sethsv_slave(h, s, v)`            |Set the LEDs on the slave side to the given HSV value, where `h`/`s`/`v` are between 0 and 255 (not written to EEPROM) |
+
+Example:
+```c
+rgblight_sethsv(HSV_WHITE, 0); // led 0
+rgblight_sethsv(HSV_RED,   1); // led 1
+rgblight_sethsv(HSV_GREEN, 2); // led 2
+// The above functions automatically calls rgblight_set(), so there is no need to call it explicitly.
+// Note that it is inefficient to call repeatedly.
+```
+
+#### effect mode change
+|Function                                    |Description  |
+|--------------------------------------------|-------------|
+|`rgblight_mode(x)`                          |Set the mode, if RGB animations are enabled |
+|`rgblight_mode_noeeprom(x)`                 |Set the mode, if RGB animations are enabled (not written to EEPROM) |
+|`rgblight_step()`                           |Change the mode to the next RGB animation in the list of enabled RGB animations |
+|`rgblight_step_noeeprom()`                  |Change the mode to the next RGB animation in the list of enabled RGB animations (not written to EEPROM) |
+|`rgblight_step_reverse()`                   |Change the mode to the previous RGB animation in the list of enabled RGB animations |
+|`rgblight_step_reverse_noeeprom()`          |Change the mode to the previous RGB animation in the list of enabled RGB animations (not written to EEPROM) |
+
+#### effects mode disable/enable
+|Function                                    |Description  |
+|--------------------------------------------|-------------|
+|`rgblight_toggle()`                         |Toggle effect range LEDs between on and off |
+|`rgblight_toggle_noeeprom()`                |Toggle effect range LEDs between on and off (not written to EEPROM) |
+|`rgblight_enable()`                         |Turn effect range LEDs on, based on their previous state |
+|`rgblight_enable_noeeprom()`                |Turn effect range LEDs on, based on their previous state (not written to EEPROM) |
+|`rgblight_disable()`                        |Turn effect range LEDs off |
+|`rgblight_disable_noeeprom()`               |Turn effect range LEDs off (not written to EEPROM) |
+
+#### hue, sat, val change
+|Function                                    |Description  |
+|--------------------------------------------|-------------|
+|`rgblight_increase_hue()`                   |Increase the hue for effect range LEDs. This wraps around at maximum hue |
+|`rgblight_increase_hue_noeeprom()`          |Increase the hue for effect range LEDs. This wraps around at maximum hue (not written to EEPROM) |
+|`rgblight_decrease_hue()`                   |Decrease the hue for effect range LEDs. This wraps around at minimum hue |
+|`rgblight_decrease_hue_noeeprom()`          |Decrease the hue for effect range LEDs. This wraps around at minimum hue (not written to EEPROM) |
+|`rgblight_increase_sat()`                   |Increase the saturation for effect range LEDs. This wraps around at maximum saturation |
+|`rgblight_increase_sat_noeeprom()`          |Increase the saturation for effect range LEDs. This wraps around at maximum saturation (not written to EEPROM) |
+|`rgblight_decrease_sat()`                   |Decrease the saturation for effect range LEDs. This wraps around at minimum saturation |
+|`rgblight_decrease_sat_noeeprom()`          |Decrease the saturation for effect range LEDs. This wraps around at minimum saturation (not written to EEPROM) |
+|`rgblight_increase_val()`                   |Increase the value for effect range LEDs. This wraps around at maximum value |
+|`rgblight_increase_val_noeeprom()`          |Increase the value for effect range LEDs. This wraps around at maximum value (not written to EEPROM) |
+|`rgblight_decrease_val()`                   |Decrease the value for effect range LEDs. This wraps around at minimum value |
+|`rgblight_decrease_val_noeeprom()`          |Decrease the value for effect range LEDs. This wraps around at minimum value (not written to EEPROM) |
+|`rgblight_sethsv(h, s, v)`                  |Set effect range LEDs to the given HSV value where `h`/`s`/`v` are between 0 and 255 |
+|`rgblight_sethsv_noeeprom(h, s, v)`         |Set effect range LEDs to the given HSV value where `h`/`s`/`v` are between 0 and 255 (not written to EEPROM) |
+
+#### query
+|Function               |Description      |
+|-----------------------|-----------------|
+|`rgblight_get_mode()`  |Get current mode |
+|`rgblight_get_hue()`   |Get current hue  |
+|`rgblight_get_sat()`   |Get current sat  |
+|`rgblight_get_val()`   |Get current val  |
 
 ## Colors
 
@@ -324,4 +380,6 @@ In addition to setting the Clipping Range, you can use `RGBLIGHT_LED_MAP` togeth
 ```
 <img src="https://user-images.githubusercontent.com/2170248/55743747-119e4c00-5a6e-11e9-91e5-013203ffae8a.JPG" alt="clip mapped" width="70%"/>
 
+## Hardware Modification
+
 If your keyboard lacks onboard underglow LEDs, you may often be able to solder on an RGB LED strip yourself. You will need to find an unused pin to wire to the data pin of your LED strip. Some keyboards may break out unused pins from the MCU to make soldering easier. The other two pins, VCC and GND, must also be connected to the appropriate power pins.

docs/feature_userspace.md

@@ -110,7 +110,7 @@ QMK has a bunch of [functions](custom_quantum_functions.md) that have [`_quantum
 However, you can actually add support for keymap version, so that you can use it in both your userspace and your keymap! 
 
 
-For instance, lets looks at the `layer_state_set_user` function.  Lets enable the [Tri Layer State](ref_functions.md#olkb-tri-layers) functionalitly to all of our boards, and then still have your `keymap.c` still able to use this functionality. 
+For instance, let's look at the `layer_state_set_user()` function.  You can enable the [Tri Layer State](ref_functions.md#olkb-tri-layers) functionality on all of your boards, while also retaining the Tri Layer functionality in your `keymap.c` files. 
 
 In your `<name.c>` file, you'd want to add this: 
 ```c

drivers/issi/is31fl3733.c

@@ -75,10 +75,10 @@ uint8_t g_twi_transfer_buffer[20];
 // buffers and the transfers in IS31FL3733_write_pwm_buffer() but it's
 // probably not worth the extra complexity.
 uint8_t g_pwm_buffer[DRIVER_COUNT][192];
-bool g_pwm_buffer_update_required = false;
+bool g_pwm_buffer_update_required[DRIVER_COUNT] = { false };
 
 uint8_t g_led_control_registers[DRIVER_COUNT][24] = { { 0 }, { 0 } };
-bool g_led_control_registers_update_required = false;
+bool g_led_control_registers_update_required[DRIVER_COUNT] = { false };
 
 void IS31FL3733_write_register( uint8_t addr, uint8_t reg, uint8_t data )
 {
@@ -123,12 +123,13 @@ void IS31FL3733_write_pwm_buffer( uint8_t addr, uint8_t *pwm_buffer )
     }
 }
 
-void IS31FL3733_init( uint8_t addr )
+void IS31FL3733_init( uint8_t addr, uint8_t sync)
 {
     // In order to avoid the LEDs being driven with garbage data
     // in the LED driver's PWM registers, shutdown is enabled last.
     // Set up the mode and other settings, clear the PWM registers,
     // then disable software shutdown.
+    // Sync is passed so set it according to the datasheet.
 
     // Unlock the command register.
     IS31FL3733_write_register( addr, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 );
@@ -161,7 +162,7 @@ void IS31FL3733_init( uint8_t addr )
     // Set global current to maximum.
     IS31FL3733_write_register( addr, ISSI_REG_GLOBALCURRENT, 0xFF );
     // Disable software shutdown.
-    IS31FL3733_write_register( addr, ISSI_REG_CONFIGURATION, 0x01 );
+    IS31FL3733_write_register( addr, ISSI_REG_CONFIGURATION, (sync << 6) | 0x01 );
 
     // Wait 10ms to ensure the device has woken up.
     #ifdef __AVR__
@@ -179,7 +180,7 @@ void IS31FL3733_set_color( int index, uint8_t red, uint8_t green, uint8_t blue )
         g_pwm_buffer[led.driver][led.r] = red;
         g_pwm_buffer[led.driver][led.g] = green;
         g_pwm_buffer[led.driver][led.b] = blue;
-        g_pwm_buffer_update_required = true;
+        g_pwm_buffer_update_required[led.driver] = true;
     }
 }
 
@@ -218,35 +219,34 @@ void IS31FL3733_set_led_control_register( uint8_t index, bool red, bool green, b
         g_led_control_registers[led.driver][control_register_b] &= ~(1 << bit_b);
     }
 
-    g_led_control_registers_update_required = true;
+    g_led_control_registers_update_required[led.driver] = true;
 
 }
 
-void IS31FL3733_update_pwm_buffers( uint8_t addr1, uint8_t addr2 )
+void IS31FL3733_update_pwm_buffers( uint8_t addr, uint8_t index )
 {
-    if ( g_pwm_buffer_update_required )
+    if ( g_pwm_buffer_update_required[index] )
     {
         // Firstly we need to unlock the command register and select PG1
-        IS31FL3733_write_register( addr1, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 );
-        IS31FL3733_write_register( addr1, ISSI_COMMANDREGISTER, ISSI_PAGE_PWM );
+        IS31FL3733_write_register( addr, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 );
+        IS31FL3733_write_register( addr, ISSI_COMMANDREGISTER, ISSI_PAGE_PWM );
 
-        IS31FL3733_write_pwm_buffer( addr1, g_pwm_buffer[0] );
-        //IS31FL3733_write_pwm_buffer( addr2, g_pwm_buffer[1] );
+        IS31FL3733_write_pwm_buffer( addr, g_pwm_buffer[index] );
     }
-    g_pwm_buffer_update_required = false;
+    g_pwm_buffer_update_required[index] = false;
 }
 
-void IS31FL3733_update_led_control_registers( uint8_t addr1, uint8_t addr2 )
+void IS31FL3733_update_led_control_registers( uint8_t addr, uint8_t index )
 {
-    if ( g_led_control_registers_update_required )
+    if ( g_led_control_registers_update_required[index] )
     {
         // Firstly we need to unlock the command register and select PG0
-        IS31FL3733_write_register( addr1, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 );
-        IS31FL3733_write_register( addr1, ISSI_COMMANDREGISTER, ISSI_PAGE_LEDCONTROL );
+        IS31FL3733_write_register( addr, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 );
+        IS31FL3733_write_register( addr, ISSI_COMMANDREGISTER, ISSI_PAGE_LEDCONTROL );
         for ( int i=0; i<24; i++ )
         {
-            IS31FL3733_write_register(addr1, i, g_led_control_registers[0][i] );
-            //IS31FL3733_write_register(addr2, i, g_led_control_registers[1][i] );
+            IS31FL3733_write_register(addr, i, g_led_control_registers[index][i] );
         }
     }
+    g_led_control_registers_update_required[index] = false;
 }

drivers/issi/is31fl3733.h

@@ -32,7 +32,7 @@ typedef struct is31_led {
 
 extern const is31_led g_is31_leds[DRIVER_LED_TOTAL];
 
-void IS31FL3733_init( uint8_t addr );
+void IS31FL3733_init( uint8_t addr, uint8_t sync );
 void IS31FL3733_write_register( uint8_t addr, uint8_t reg, uint8_t data );
 void IS31FL3733_write_pwm_buffer( uint8_t addr, uint8_t *pwm_buffer );
 
@@ -45,8 +45,8 @@ void IS31FL3733_set_led_control_register( uint8_t index, bool red, bool green, b
 // (eg. from a timer interrupt).
 // Call this while idle (in between matrix scans).
 // If the buffer is dirty, it will update the driver with the buffer.
-void IS31FL3733_update_pwm_buffers( uint8_t addr1, uint8_t addr2 );
-void IS31FL3733_update_led_control_registers( uint8_t addr1, uint8_t addr2 );
+void IS31FL3733_update_pwm_buffers( uint8_t addr, uint8_t index );
+void IS31FL3733_update_led_control_registers( uint8_t addr, uint8_t index );
 
 #define A_1  0x00
 #define A_2  0x01

keyboards/40percentclub/nein/config.h

@@ -0,0 +1,239 @@
+/* Copyright 2019
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x0A0C
+#define DEVICE_VER      0x9999
+#define MANUFACTURER    di0ib
+#define PRODUCT         The nein Keyboard
+#define DESCRIPTION     9 key macropad
+
+/* key matrix size */
+#define MATRIX_ROWS 3
+#define MATRIX_COLS 3
+
+/* Keyboard Matrix Assignments */
+#define DIRECT_PINS { \
+    { F4, F5, F6 }, \
+    { F7, B1, B3 }, \
+    { B2, B6, B5 }  \
+}
+#define UNUSED_PINS
+
+/*
+ * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.
+ */
+// #define SOFT_SERIAL_PIN D0 // or D1, D2, D3, E6
+
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+// #define RGB_DI_PIN E2
+// #ifdef RGB_DI_PIN
+//   #define RGBLED_NUM 16
+//   #define RGBLIGHT_HUE_STEP 8
+//   #define RGBLIGHT_SAT_STEP 8
+//   #define RGBLIGHT_VAL_STEP 8
+//   #define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */
+//   #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
+// /*== all animations enable ==*/
+//   #define RGBLIGHT_ANIMATIONS
+// /*== or choose animations ==*/
+//   #define RGBLIGHT_EFFECT_BREATHING
+//   #define RGBLIGHT_EFFECT_RAINBOW_MOOD
+//   #define RGBLIGHT_EFFECT_RAINBOW_SWIRL
+//   #define RGBLIGHT_EFFECT_SNAKE
+//   #define RGBLIGHT_EFFECT_KNIGHT
+//   #define RGBLIGHT_EFFECT_CHRISTMAS
+//   #define RGBLIGHT_EFFECT_STATIC_GRADIENT
+//   #define RGBLIGHT_EFFECT_RGB_TEST
+//   #define RGBLIGHT_EFFECT_ALTERNATING
+// /*== customize breathing effect ==*/
+//   /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/
+//   #define RGBLIGHT_BREATHE_TABLE_SIZE 256      // 256(default) or 128 or 64
+//   /*==== use exp() and sin() ====*/
+//   #define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85  // 1 to 2.7
+//   #define RGBLIGHT_EFFECT_BREATHE_MAX    255   // 0 to 255
+// #endif
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+/* defined by default; to change, uncomment and set to the combination you want */
+// #define IS_COMMAND() (get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP           H
+//#define MAGIC_KEY_HELP_ALT       SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER0_ALT     GRAVE
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     B
+//#define MAGIC_KEY_BOOTLOADER_ALT ESC
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_EEPROM_CLEAR   BSPACE
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
+#endif
+*/
+
+/* Bootmagic Lite key configuration */
+// #define BOOTMAGIC_LITE_ROW 0
+// #define BOOTMAGIC_LITE_COLUMN 0

keyboards/40percentclub/nein/info.json

@@ -0,0 +1,22 @@
+{
+  "keyboard_name": "nein",
+  "url": "",
+  "maintainer": "qmk",
+  "width": 3,
+  "height": 3,
+  "layouts": {
+    "LAYOUT": {
+      "layout": [
+        {"x":0, "y":0},
+        {"x":1, "y":0},
+        {"x":2, "y":0},
+        {"x":0, "y":1},
+        {"x":1, "y":1},
+        {"x":2, "y":1},
+        {"x":0, "y":2},
+        {"x":1, "y":2},
+        {"x":2, "y":2}
+      ]
+    }
+  }
+}

keyboards/40percentclub/nein/keymaps/default/keymap.c

@@ -0,0 +1,29 @@
+/* Copyright 2019
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+    [0] = LAYOUT_ortho_3x3(
+        KC_MUTE, KC_HOME, KC_MPLY, \
+        MO(1),   KC_UP,   KC_END, \
+        KC_LEFT, KC_DOWN, KC_RGHT \
+    ),
+    [1] = LAYOUT_ortho_3x3(
+        RESET,   _______, KC_STOP, \
+        _______, _______, RGB_MOD, \
+        KC_MPRV, _______, KC_MNXT \
+    ),
+};

keyboards/40percentclub/nein/nein.c

@@ -0,0 +1,16 @@
+/* Copyright 2019
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "nein.h"

keyboards/40percentclub/nein/nein.h

@@ -0,0 +1,37 @@
+/* Copyright 2019
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+#define LAYOUT_ortho_3x3( \
+    k00, k01, k02, \
+    k10, k11, k12, \
+    k20, k21, k22  \
+) \
+{ \
+    { k00, k01, k02 }, \
+    { k10, k11, k12 }, \
+    { k20, k21, k22 }  \
+}

keyboards/40percentclub/nein/readme.md

@@ -0,0 +1,18 @@
+# nein
+
+![nein](https://2.bp.blogspot.com/-avYV4grcAPQ/XL9a67SxgKI/AAAAAAACVCE/GSGVYRThaEEDd14M3LG34gQTv5ZabRI0QCEwYBhgL/s640/a.jpg)
+===
+
+A 9 key macropad.
+
+Powered by a Pro Micro and can fit any of the various different sized variations of Pro Micro.
+
+Keyboard Maintainer: QMK Community  
+Hardware Supported: nein PCB  
+Hardware Availability: [nein project on 40% Keyboards](https://www.40percent.club/2019/04/nein.html)
+
+Make example for this keyboard (after setting up your build environment):
+
+    make 40percentclub/nein:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/40percentclub/nein/rules.mk

@@ -0,0 +1,80 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   atmega32a    bootloadHID
+BOOTLOADER = caterina
+
+
+# If you don't know the bootloader type, then you can specify the
+# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
+#   Teensy halfKay      512
+#   Teensy++ halfKay    1024
+#   Atmel DFU loader    4096
+#   LUFA bootloader     4096
+#   USBaspLoader        2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = lite     # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no         # Console for debug(+400)
+COMMAND_ENABLE = no         # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = yes           # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 	    # Enable support for HD44780 based LCDs (+400)

keyboards/ai03/lunar/info.json

@@ -7,7 +7,78 @@
     "height": 5, 
     "layouts": {
         "LAYOUT": {
-            "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"label":"Backspace", "x":13, "y":0, "w":2}, {"label":"Insert", "x":15, "y":0}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"{", "x":11.5, "y":1}, {"label":"}", "x":12.5, "y":1}, {"label":"|", "x":13.5, "y":1, "w":1.5}, {"label":"Delete", "x":15, "y":1}, {"label":"Caps Lock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"label":"Enter", "x":12.75, "y":2, "w":2.25}, {"label":"Home", "x":15, "y":2}, {"label":"Shift", "x":0, "y":3, "w":2.25}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":1.75}, {"label":"\u2191", "x":14, "y":3}, {"label":"End", "x":15, "y":3}, {"label":"Ctrl", "x":0, "y":4, "w":1.5}, {"label":"Win", "x":1.5, "y":4, "w":1.25}, {"label":"Alt", "x":2.75, "y":4, "w":1.5}, {"x":4.25, "y":4, "w":2.25}, {"x":6.5, "y":4, "w":1.5}, {"x":8, "y":4, "w":2.75}, {"label":"Alt", "x":10.75, "y":4, "w":1.25}, {"label":"Win", "x":12, "y":4}, {"label":"\u2190", "x":13, "y":4}, {"label":"\u2193", "x":14, "y":4}, {"label":"\u2192", "x":15, "y":4}]
+            "layout": [
+                {"label":"Esc", "x":0, "y":0},
+                {"label":"!", "x":1, "y":0},
+                {"label":"@", "x":2, "y":0},
+                {"label":"#", "x":3, "y":0},
+                {"label":"$", "x":4, "y":0},
+                {"label":"%", "x":5, "y":0},
+                {"label":"^", "x":6, "y":0},
+                {"label":"&", "x":7, "y":0},
+                {"label":"*", "x":8, "y":0},
+                {"label":"(", "x":9, "y":0},
+                {"label":")", "x":10, "y":0},
+                {"label":"_", "x":11, "y":0},
+                {"label":"+", "x":12, "y":0},
+                {"label":"BackspaceL", "x":13, "y":0},
+                {"label":"BackspaceR", "x":14, "y":0},
+                {"label":"Insert", "x":15, "y":0},
+                {"label":"Tab", "x":0, "y":1, "w":1.5},
+                {"label":"Q", "x":1.5, "y":1},
+                {"label":"W", "x":2.5, "y":1},
+                {"label":"E", "x":3.5, "y":1},
+                {"label":"R", "x":4.5, "y":1},
+                {"label":"T", "x":5.5, "y":1},
+                {"label":"Y", "x":6.5, "y":1},
+                {"label":"U", "x":7.5, "y":1},
+                {"label":"I", "x":8.5, "y":1},
+                {"label":"O", "x":9.5, "y":1},
+                {"label":"P", "x":10.5, "y":1},
+                {"label":"{", "x":11.5, "y":1},
+                {"label":"}", "x":12.5, "y":1},
+                {"label":"|", "x":13.5, "y":1, "w":1.5},
+                {"label":"Delete", "x":15, "y":1},
+                {"label":"Caps Lock", "x":0, "y":2, "w":1.75},
+                {"label":"A", "x":1.75, "y":2},
+                {"label":"S", "x":2.75, "y":2},
+                {"label":"D", "x":3.75, "y":2},
+                {"label":"F", "x":4.75, "y":2},
+                {"label":"G", "x":5.75, "y":2},
+                {"label":"H", "x":6.75, "y":2},
+                {"label":"J", "x":7.75, "y":2},
+                {"label":"K", "x":8.75, "y":2},
+                {"label":"L", "x":9.75, "y":2},
+                {"label":":", "x":10.75, "y":2},
+                {"label":"\"", "x":11.75, "y":2},
+                {"label":"Enter", "x":12.75, "y":2, "w":2.25},
+                {"label":"Home", "x":15, "y":2},
+                {"label":"Shift", "x":0, "y":3, "w":2.25},
+                {"label":"Z", "x":2.25, "y":3},
+                {"label":"X", "x":3.25, "y":3},
+                {"label":"C", "x":4.25, "y":3},
+                {"label":"V", "x":5.25, "y":3},
+                {"label":"B", "x":6.25, "y":3},
+                {"label":"N", "x":7.25, "y":3},
+                {"label":"M", "x":8.25, "y":3},
+                {"label":"<", "x":9.25, "y":3},
+                {"label":">", "x":10.25, "y":3},
+                {"label":"?", "x":11.25, "y":3},
+                {"label":"Shift", "x":12.25, "y":3, "w":1.75},
+                {"label":"\u2191", "x":14, "y":3},
+                {"label":"End", "x":15, "y":3},
+                {"label":"Ctrl", "x":0, "y":4, "w":1.5},
+                {"label":"Win", "x":1.5, "y":4, "w":1.25},
+                {"label":"Alt", "x":2.75, "y":4, "w":1.5},
+                {"x":4.25, "y":4, "w":2.25},
+                {"x":6.5, "y":4, "w":1.5},
+                {"x":8, "y":4, "w":2.75},
+                {"label":"Alt", "x":10.75, "y":4, "w":1.25},
+                {"label":"Win", "x":12, "y":4},
+                {"label":"\u2190", "x":13, "y":4},
+                {"label":"\u2193", "x":14, "y":4},
+                {"label":"\u2192", "x":15, "y":4}
+            ]
         }
     }
 }

keyboards/ai03/orbit/info.json

@@ -0,0 +1,88 @@
+{
+    "keyboard_name": "orbit", 
+    "url": "https://github.com/ai03-2725/Orbit", 
+    "maintainer": "ai03", 
+    "width": 16, 
+    "height": 6, 
+    "layouts": {
+        "LAYOUT": {
+            "layout": [
+                {"x":0,  "y":0.63},
+                {"x":1,  "y":0.38},
+                {"x":2,  "y":0.38},
+                {"x":3,  "y":0.13},
+                {"x":4,  "y":0},
+                {"x":5,  "y":0.13},
+                {"x":6,  "y":0.25},
+                {"x":9,  "y":0.25},
+                {"x":10, "y":0.13},
+                {"x":11, "y":0},
+                {"x":12, "y":0.13},
+                {"x":13, "y":0.38},
+                {"x":14, "y":0.38},
+                {"x":15, "y":0.63},
+
+                {"x":0,  "y":1.63},
+                {"x":1,  "y":1.38},
+                {"x":2,  "y":1.38},
+                {"x":3,  "y":1.13},
+                {"x":4,  "y":1},
+                {"x":5,  "y":1.13},
+                {"x":6,  "y":1.25},
+                {"x":9,  "y":1.25},
+                {"x":10, "y":1.13},
+                {"x":11, "y":1},
+                {"x":12, "y":1.13},
+                {"x":13, "y":1.38},
+                {"x":14, "y":1.38},
+                {"x":15, "y":1.63},
+
+                {"x":0,  "y":2.63},
+                {"x":1,  "y":2.38},
+                {"x":2,  "y":2.38},
+                {"x":3,  "y":2.13},
+                {"x":4,  "y":2},
+                {"x":5,  "y":2.13},
+                {"x":6,  "y":2.25},
+                {"x":9,  "y":2.25},
+                {"x":10, "y":2.13},
+                {"x":11, "y":2},
+                {"x":12, "y":2.13},
+                {"x":13, "y":2.38},
+                {"x":14, "y":2.38},
+                {"x":15, "y":2.63},
+
+                {"x":0,  "y":3.63},
+                {"x":1,  "y":3.38},
+                {"x":2,  "y":3.38},
+                {"x":3,  "y":3.13},
+                {"x":4,  "y":3},
+                {"x":5,  "y":3.13},
+                {"x":6,  "y":3.25},
+                {"x":9,  "y":3.25},
+                {"x":10, "y":3.13},
+                {"x":11, "y":3},
+                {"x":12, "y":3.13},
+                {"x":13, "y":3.38},
+                {"x":14, "y":3.38},
+                {"x":15, "y":3.63},
+
+                {"x":1,  "y":4.38},
+                {"x":2,  "y":4.38},
+                {"x":3,  "y":4.13},
+                {"x":4,  "y":4},
+
+                {"x":5.5, "y":4.25},
+                {"x":6.5, "y":4.5, "h":1.5},
+
+                {"x":8.5, "y":4.5, "h":1.5},
+                {"x":9.5, "y":4.25},
+
+                {"x":11, "y":4},
+                {"x":12, "y":4.13},
+                {"x":13, "y":4.38},
+                {"x":14, "y":4.38}
+            ]
+        }
+    }
+}

keyboards/butterstick/keymaps/default/keymap.c

@@ -45,6 +45,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 uint32_t processQwerty(bool lookup) {
     // SECRET AGENT CHORDS
     P( LSU | LK | RS | RD,    	SEND_STRING(VERSION); SEND_STRING(__DATE__));
+	P( LR  | ST2| RR | RB, 		SEND(KC_BSPC));
     P( LSD | RZ,   			 	SEND(KC_SPC));
 
     // Dual chords

keyboards/cannonkeys/instant60/config.h

@@ -66,12 +66,18 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 // Bump this every time we change what we store
 // This will automatically reset the EEPROM with defaults
 // and avoid loading invalid data from the EEPROM
-#define EEPROM_VERSION 0x01
+#define EEPROM_VERSION 0x02
 #define EEPROM_VERSION_ADDR 34
 
-#define EEPROM_CUSTOM_BACKLIGHT 804
-
 
+#define DYNAMIC_KEYMAP_LAYER_COUNT 4
+// Dynamic macro starts after dynamic keymaps (35+(4*5*15*2)) = (35+600) = 635
+// start + layer * rows * col * 2
+#define DYNAMIC_KEYMAP_EEPROM_ADDR 35
+#define EEPROM_CUSTOM_BACKLIGHT 636
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 637
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 200
+#define DYNAMIC_KEYMAP_MACRO_COUNT 16
 
 /*
  * Feature disable options

keyboards/cannonkeys/instant60/info.json

@@ -0,0 +1,15 @@
+{
+    "keyboard_name": "Instant60",
+    "url": "https://cannonkeys.com",
+    "maintainer": "awkannan",
+    "width": 15,
+    "height": 5,
+    "layouts": {
+        "LAYOUT_ansi": {
+            "layout": [{"label":"~", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"label":"Backspace", "x":13, "y":0, "w":2}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"{", "x":11.5, "y":1}, {"label":"}", "x":12.5, "y":1}, {"label":"|", "x":13.5, "y":1, "w":1.5}, {"label":"Caps Lock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"label":"Enter", "x":12.75, "y":2, "w":2.25}, {"label":"Shift", "x":0, "y":3, "w":2.25}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":2.75}, {"label":"Ctrl", "x":0, "y":4, "w":1.25}, {"label":"Win", "x":1.25, "y":4, "w":1.25}, {"label":"Alt", "x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.25}, {"label":"Alt", "x":10, "y":4, "w":1.25}, {"label":"Win", "x":11.25, "y":4, "w":1.25}, {"label":"Menu", "x":12.5, "y":4, "w":1.25}, {"label":"Ctrl", "x":13.75, "y":4, "w":1.25}]
+        },
+        "LAYOUT_tsangan": {
+            "layout": [{"label":"~", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"{", "x":11.5, "y":1}, {"label":"}", "x":12.5, "y":1}, {"label":"|", "x":13.5, "y":1, "w":1.5}, {"label":"Caps Lock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"label":"Enter", "x":12.75, "y":2, "w":2.25}, {"label":"Shift", "x":0, "y":3, "w":2.25}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":1.75}, {"x":14, "y":3}, {"label":"Ctrl", "x":0, "y":4, "w":1.5}, {"label":"Win", "x":1.5, "y":4}, {"label":"Alt", "x":2.5, "y":4, "w":1.5}, {"x":4, "y":4, "w":7}, {"label":"Alt", "x":11, "y":4, "w":1.5}, {"label":"Win", "x":12.5, "y":4}, {"label":"Ctrl", "x":13.5, "y":4, "w":1.5}]
+        }
+    }
+}

keyboards/cannonkeys/instant60/keymaps/tsangan/keymap.c

@@ -31,18 +31,18 @@ enum custom_keycodes {
 
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
   [_BASE] = LAYOUT_tsangan(
-    KC_GESC, KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,                 KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,   KC_BSPC, KC_DEL, \
-    KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,   KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC,  KC_BSLS, \
+    KC_GESC, KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,                 KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,   KC_BSLS, KC_DEL, \
+    KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,   KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC,  KC_BSPC, \
     KC_CAPS, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,                 KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT,           KC_ENT,  \
     KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,                 KC_M,    KC_COMM, KC_DOT,  KC_SLSH,                    KC_RSFT, MO(_FN1),\
     KC_LCTL, KC_LGUI, KC_LALT,                            KC_SPC,                                          KC_RALT, KC_RGUI, KC_RCTL
   ),
 
   [_FN1] = LAYOUT_tsangan(
-    KC_GESC, KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_DEL, _______,\
+    KC_GRV, KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_DEL, _______,\
     RGB_TOG, RGB_MOD, KC_UP,   _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \
     BL_BRTG, KC_LEFT, KC_DOWN, KC_RGHT, _______, _______, _______, _______, _______, _______, _______, _______,          _______, \
     BL_INC,  BL_DEC,  BL_TOGG, _______, _______, _______, _______, _______, _______, _______, _______,                   _______, _______,\
-    KC_GRV,  _______, _______,                            _______,                            _______, _______, RESET
+    _______,  _______, _______,                            _______,                            _______, _______, RESET
   )
 };

keyboards/cannonkeys/instant60/keymaps/via/keymap.c

@@ -0,0 +1,43 @@
+/*
+Copyright 2012,2013 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+#include QMK_KEYBOARD_H
+
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+#define _BASE 0
+#define _FN1 1
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  [_BASE] = LAYOUT_all(
+    KC_GESC, KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,                 KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,   KC_BSLS, KC_DEL,
+    KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,   KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC,  KC_BSPC,
+    KC_CAPS, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,                 KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT,           KC_ENT,
+    KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,                 KC_M,    KC_COMM, KC_DOT,  KC_SLSH,                    KC_RSFT, MO(_FN1),
+    KC_LCTL, KC_LGUI, KC_LALT,                            KC_SPC,                                          KC_RALT, KC_RGUI, MO(_FN1), KC_RCTL
+  ),
+
+  [_FN1] = LAYOUT_all(
+    KC_GRV, KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_DEL, _______,
+    RGB_TOG, RGB_MOD, KC_UP,   _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+    BL_BRTG, KC_LEFT, KC_DOWN, KC_RGHT, _______, _______, _______, _______, _______, _______, _______, _______,          _______,
+    BL_INC,  BL_DEC,  BL_TOGG, _______, _______, _______, _______, _______, _______, _______, _______,                   _______, _______,
+    _______,  _______, _______,                            _______,                            _______, _______, _______, RESET
+  )
+};

keyboards/cannonkeys/instant60/keymaps/via/rules.mk

@@ -0,0 +1,5 @@
+# rules.mk overrides to enable VIA
+
+RAW_ENABLE = yes
+DYNAMIC_KEYMAP_ENABLE = yes
+

keyboards/cannonkeys/instant60/keymaps/via_standard/keymap.c

@@ -0,0 +1,43 @@
+/*
+Copyright 2012,2013 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+#include QMK_KEYBOARD_H
+
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+#define _BASE 0
+#define _FN1 1
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  [_BASE] = LAYOUT_all(
+    KC_GESC, KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,                 KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,   KC_BSPC, KC_DEL,
+    KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,   KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC,  KC_BSLS,
+    KC_CAPS, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,                 KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT,           KC_ENT,
+    KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,                 KC_M,    KC_COMM, KC_DOT,  KC_SLSH,                    KC_RSFT, MO(_FN1),
+    KC_LCTL, KC_LGUI, KC_LALT,                            KC_SPC,                                          KC_RALT, KC_RGUI, MO(_FN1), KC_RCTL
+  ),
+
+  [_FN1] = LAYOUT_all(
+    KC_GRV, KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_DEL, _______,
+    RGB_TOG, RGB_MOD, KC_UP,   _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+    BL_BRTG, KC_LEFT, KC_DOWN, KC_RGHT, _______, _______, _______, _______, _______, _______, _______, _______,          _______,
+    BL_INC,  BL_DEC,  BL_TOGG, _______, _______, _______, _______, _______, _______, _______, _______,                   _______, _______,
+    _______,  _______, _______,                            _______,                            _______, _______, _______, RESET
+  )
+};

keyboards/cannonkeys/instant60/keymaps/via_standard/rules.mk

@@ -0,0 +1,5 @@
+# rules.mk overrides to enable VIA
+
+RAW_ENABLE = yes
+DYNAMIC_KEYMAP_ENABLE = yes
+

keyboards/cannonkeys/practice65/info.json

@@ -0,0 +1,12 @@
+{
+    "keyboard_name": "Practice65",
+    "url": "https://cannonkeys.com",
+    "maintainer": "awkannan",
+    "width": 16,
+    "height": 5,
+    "layouts": {
+        "LAYOUT_default": {
+            "layout": [{"label":"~", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":15, "y":0}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"{", "x":11.5, "y":1}, {"label":"}", "x":12.5, "y":1}, {"label":"|", "x":13.5, "y":1, "w":1.5}, {"x":15, "y":1}, {"label":"Caps Lock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"label":"Enter", "x":12.75, "y":2, "w":2.25}, {"x":15, "y":2}, {"label":"Shift", "x":0, "y":3, "w":2.25}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":1.75}, {"x":14, "y":3}, {"x":15, "y":3}, {"label":"Ctrl", "x":0, "y":4, "w":1.25}, {"label":"Win", "x":1.25, "y":4, "w":1.25}, {"label":"Alt", "x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.25}, {"x":10, "y":4}, {"x":11, "y":4}, {"x":12, "y":4}, {"x":13, "y":4}, {"x":14, "y":4}, {"x":15, "y":4}]
+        }
+    }
+}

keyboards/cannonkeys/stm32f072/keyboard.c

@@ -5,9 +5,16 @@
 #include "util.h"
 #include "quantum.h"
 
+#include "ws2812.h"
+
+#include "raw_hid.h"
+#include "dynamic_keymap.h"
 #include "tmk_core/common/eeprom.h"
 
-#include "ws2812.h"
+// HACK
+#include "keyboards/zeal60/zeal60_api.h" // Temporary hack
+#include "keyboards/zeal60/zeal60_keycodes.h" // Temporary hack
+
 
 backlight_config_t kb_backlight_config = {
   .enable = true,
@@ -41,6 +48,17 @@ void load_custom_config(){
   kb_backlight_config.raw = eeprom_read_byte((uint8_t*)EEPROM_CUSTOM_BACKLIGHT);
 }
 
+#ifdef DYNAMIC_KEYMAP_ENABLE
+void dynamic_keymap_custom_reset(void){
+    void *p = (void*)(EEPROM_CUSTOM_BACKLIGHT);
+	void *end = (void*)(DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR);
+	while ( p != end ) {
+		eeprom_update_byte(p, 0);
+		++p;
+	}
+}
+#endif
+
 void eeprom_init_kb(void)
 {
 	// If the EEPROM has the magic, the data is good.
@@ -48,9 +66,17 @@ void eeprom_init_kb(void)
 	if (eeprom_is_valid()) {
 		load_custom_config();
 	} else	{
+#ifdef DYNAMIC_KEYMAP_ENABLE
+		// This resets the keymaps in EEPROM to what is in flash.
+		dynamic_keymap_reset();
+		// This resets the macros in EEPROM to nothing.
+		dynamic_keymap_macro_reset();
+        // Reset the custom stuff
+        dynamic_keymap_custom_reset();
+#endif
 		// Save the magic number last, in case saving was interrupted
+        save_backlight_config_to_eeprom();
 		eeprom_set_valid(true);
-    save_backlight_config_to_eeprom();
 	}
 }
 
@@ -120,6 +146,158 @@ bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
         save_backlight_config_to_eeprom();
       }
       return false;
+    default:
+        break;
   }
+
+  #ifdef DYNAMIC_KEYMAP_ENABLE
+	// Handle macros
+	if (record->event.pressed) {
+		if ( keycode >= MACRO00 && keycode <= MACRO15 )
+		{
+			uint8_t id = keycode - MACRO00;
+			dynamic_keymap_macro_send(id);
+			return false;
+		}
+	}
+    #endif //DYNAMIC_KEYMAP_ENABLE
+
   return true;
 }
+
+
+// Start Dynamic Keymap code
+#ifdef RAW_ENABLE
+
+void raw_hid_receive( uint8_t *data, uint8_t length )
+{
+	uint8_t *command_id = &(data[0]);
+	uint8_t *command_data = &(data[1]);
+	switch ( *command_id )
+	{
+		case id_get_protocol_version:
+		{
+			command_data[0] = PROTOCOL_VERSION >> 8;
+			command_data[1] = PROTOCOL_VERSION & 0xFF;
+			break;
+		}
+		case id_get_keyboard_value:
+		{
+            switch( command_data[0])
+            {
+                case id_uptime:
+                {
+                uint32_t value = timer_read32();
+                command_data[1] = (value >> 24 ) & 0xFF;
+                command_data[2] = (value >> 16 ) & 0xFF;
+                command_data[3] = (value >> 8 ) & 0xFF;
+                command_data[4] = value & 0xFF;
+                break;
+                }
+                default:
+                {
+                *command_id = id_unhandled;
+                break;
+                }
+            }
+            break;
+        }
+#ifdef DYNAMIC_KEYMAP_ENABLE
+
+		case id_dynamic_keymap_get_keycode:
+		{
+			uint16_t keycode = dynamic_keymap_get_keycode( command_data[0], command_data[1], command_data[2] );
+			command_data[3] = keycode >> 8;
+			command_data[4] = keycode & 0xFF;
+			break;
+		}
+		case id_dynamic_keymap_set_keycode:
+		{
+			dynamic_keymap_set_keycode( command_data[0], command_data[1], command_data[2], ( command_data[3] << 8 ) | command_data[4] );
+			break;
+		}
+		case id_dynamic_keymap_reset:
+		{
+			dynamic_keymap_reset();
+			break;
+		}
+		case id_dynamic_keymap_macro_get_count:
+		{
+			command_data[0] = dynamic_keymap_macro_get_count();
+			break;
+		}
+		case id_dynamic_keymap_macro_get_buffer_size:
+		{
+			uint16_t size = dynamic_keymap_macro_get_buffer_size();
+			command_data[0] = size >> 8;
+			command_data[1] = size & 0xFF;
+			break;
+		}
+		case id_dynamic_keymap_macro_get_buffer:
+		{
+			uint16_t offset = ( command_data[0] << 8 ) | command_data[1];
+			uint16_t size = command_data[2]; // size <= 28
+			dynamic_keymap_macro_get_buffer( offset, size, &command_data[3] );
+			break;
+		}
+		case id_dynamic_keymap_macro_set_buffer:
+		{
+			uint16_t offset = ( command_data[0] << 8 ) | command_data[1];
+			uint16_t size = command_data[2]; // size <= 28
+			dynamic_keymap_macro_set_buffer( offset, size, &command_data[3] );
+			break;
+		}
+		case id_dynamic_keymap_macro_reset:
+		{
+			dynamic_keymap_macro_reset();
+			break;
+		}
+		case id_dynamic_keymap_get_layer_count:
+		{
+			command_data[0] = dynamic_keymap_get_layer_count();
+			break;
+		}
+		case id_dynamic_keymap_get_buffer:
+		{
+			uint16_t offset = ( command_data[0] << 8 ) | command_data[1];
+			uint16_t size = command_data[2]; // size <= 28
+			dynamic_keymap_get_buffer( offset, size, &command_data[3] );
+			break;
+		}
+		case id_dynamic_keymap_set_buffer:
+		{
+			uint16_t offset = ( command_data[0] << 8 ) | command_data[1];
+			uint16_t size = command_data[2]; // size <= 28
+			dynamic_keymap_set_buffer( offset, size, &command_data[3] );
+			break;
+		}
+#endif // DYNAMIC_KEYMAP_ENABLE
+		case id_eeprom_reset:
+		{
+			eeprom_reset();
+			break;
+		}
+		case id_bootloader_jump:
+		{
+			// Need to send data back before the jump
+			// Informs host that the command is handled
+			raw_hid_send( data, length );
+			// Give host time to read it
+			wait_ms(100);
+			bootloader_jump();
+			break;
+		}
+		default:
+		{
+			// Unhandled message.
+			*command_id = id_unhandled;
+			break;
+		}
+	}
+
+	// Return same buffer with values changed
+	raw_hid_send( data, length );
+
+}
+
+#endif

keyboards/cannonkeys/stm32f072/led.c

@@ -77,10 +77,9 @@ void backlight_init_ports(void) {
   pwmStart(&PWMD3, &pwmCFG);
   // pwmEnableChannel(&PWMD3, 0, PWM_FRACTION_TO_WIDTH(&PWMD3, 0xFFFF,cie_lightness(0xFFFF)));
   if(kb_backlight_config.enable){
+    backlight_set(kb_backlight_config.level);
     if(kb_backlight_config.breathing){
       breathing_enable();
-    } else{
-      backlight_set(kb_backlight_config.level);
     }
   } else {
     backlight_set(0);

keyboards/claw44/ssd1306.c

@@ -13,7 +13,7 @@
 #include "sendchar.h"
 #include "timer.h"
 
-static const unsigned char font[] PROGMEM;
+extern const unsigned char font[] PROGMEM;
 
 // Set this to 1 to help diagnose early startup problems
 // when testing power-on with ble.  Turn it off otherwise,

keyboards/comet46/ssd1306.c

@@ -13,7 +13,7 @@
 #include "sendchar.h"
 #include "timer.h"
 
-static const unsigned char font[] PROGMEM;
+extern const unsigned char font[] PROGMEM;
 
 // Set this to 1 to help diagnose early startup problems
 // when testing power-on with ble.  Turn it off otherwise,

keyboards/converter/modelm101/keymaps/default/keymap.c

@@ -21,7 +21,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
     KC_GRV,  KC_1,    KC_2,   KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC,   KC_INS,  KC_HOME, KC_PGUP,   KC_NLCK, KC_PSLS, KC_PAST, KC_PMNS,
     KC_TAB,  KC_Q,    KC_W,   KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS,   KC_DEL,  KC_END,  KC_PGDN,   KC_P7,   KC_P8,   KC_P9,   KC_PPLS,
     KC_CAPS, KC_A,    KC_S,   KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_NUHS, KC_ENT,                                 KC_P4,   KC_P5,   KC_P6,
-    KC_LSFT, KC_NUBS, KC_Z,   KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH,          KC_RSFT,            KC_UP,              KC_P1,   KC_P2,   KC_P3,   KC_LGUI,
+    KC_LSFT, KC_NUBS, KC_Z,   KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH,          KC_RSFT,            KC_UP,              KC_P1,   KC_P2,   KC_P3,   KC_PENT,
     KC_LCTL,          KC_LALT,                           KC_SPC,                                      KC_RALT,          KC_RCTL,   KC_LEFT, KC_DOWN, KC_RGHT,   KC_P0,            KC_PDOT
   ),
 };

keyboards/coseyfannitutti/mullet/config.h

@@ -0,0 +1,172 @@
+/*
+Copyright 2019 COSEYFANNITUTTI
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6969
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    coseyfannitutti
+#define PRODUCT         mullet
+#define DESCRIPTION     65% keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 15
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { D0, D1, B0, F0, F1 }
+#define MATRIX_COL_PINS { B2, F4, F5, F6, F7, C7, C6, B6, B5, B4, D7, D6, D4, D2, D3 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */
+#define DIODE_DIRECTION COL2ROW
+
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+#define RGB_DI_PIN D5
+#ifdef RGB_DI_PIN
+#define RGBLIGHT_ANIMATIONS
+#define RGBLED_NUM 14
+#define RGBLIGHT_HUE_STEP 8
+#define RGBLIGHT_SAT_STEP 8
+#define RGBLIGHT_VAL_STEP 8
+#define RGBLIGHT_SLEEP
+#endif
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+//#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+//#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
+#endif
+*/
+

keyboards/coseyfannitutti/mullet/info.json

@@ -0,0 +1,12 @@
+{
+    "keyboard_name": "mullet", 
+    "url": "https://github.com/coseyfannitutti/mullet", 
+    "maintainer": "coseyfannitutti", 
+    "width": 16, 
+    "height": 5, 
+    "layouts": {
+        "LAYOUT": {
+            "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"label":"Backspace", "x":13, "y":0, "w":2}, {"label":"Insert", "x":15, "y":0}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"{", "x":11.5, "y":1}, {"label":"}", "x":12.5, "y":1}, {"label":"|", "x":13.5, "y":1, "w":1.5}, {"label":"Page Up", "x":15, "y":1}, {"label":"Caps Lock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"label":"Enter", "x":12.75, "y":2, "w":2.25}, {"label":"Page Down", "x":15, "y":2}, {"label":"Shift", "x":0, "y":3, "w":2.25}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":1.75}, {"label":"\u2191", "x":14, "y":3}, {"label":"End", "x":15, "y":3}, {"label":"Ctrl", "x":0, "y":4, "w":1.25}, {"label":"Win", "x":1.25, "y":4, "w":1.25}, {"label":"Alt", "x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.25}, {"label":"Alt", "x":10, "y":4, "w":1.25}, {"label":"Fn", "x":11.25, "y":4, "w":1.25}, {"label":"\u2190", "x":13, "y":4}, {"label":"\u2193", "x":14, "y":4}, {"label":"\u2192", "x":15, "y":4}]
+        }
+    }
+}

keyboards/coseyfannitutti/mullet/keymaps/alternate/keymap.c

@@ -0,0 +1,68 @@
+/* Copyright 2019 COSEYFANNITUTTI
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+#define _BL 0
+#define _FL 1
+
+  /* Qwerty
+   * .---------------------------------------------------------------------------------------------.
+   * | Esc |  1  |  2  |  3  |  4  |  5  |  6  |  7  |  8  |  9  |  0  |  -  |  =  |  Bkspc  | Del |
+   * |---------------------------------------------------------------------------------------------+
+   * | Tab    |  Q  |  W  |  E  |  R  |  T  |  Y  |  U  |  I  |  O  |  P  |  [  |  ]  |   \  | PgUp|
+   * |---------------------------------------------------------------------------------------------+
+   * | Caps    |  A  |  S  |  D  |  F  |  G  |  H  |  J  |  K  |  L  |  ;  |  '  |   Enter   | PgDn|
+   * |---------------------------------------------------------------------------------------------+
+   * | Shift     |  Z  |  X  |  C  |  V  |  B  |  N  |  M  |  ,  |  .  |  /  |  Shift  | Up  | Fn  |
+   * |---------------------------------------------------------------------------------------------+
+   * | Ctrl |  Win  |  Alt  |              Space                | RAlt | Fn  |||||Left |Down |Right|
+   * '---------------------------------------------------------------------------------------------'
+   */
+
+  /* FnLayer
+   * .---------------------------------------------------------------------------------------------.
+   * | ` ~ |  F1 |  F2 |  F3 |  F4 |  F5 |  F6 |  F7 |  F8 |  F9 | F10 | F11 | F12 |  Delete |     |
+   * |---------------------------------------------------------------------------------------------+
+   * | Tab    |STATC|BRTHE|RNBOW|RESET|     |     |     |     |     |     |PrScr|     |  \   | Home|
+   * |---------------------------------------------------------------------------------------------+
+   * | Caps    |RGBH+|RGBS+|RGBB+|     |     |     |     |     |     |     |     |    Enter  | End |
+   * |---------------------------------------------------------------------------------------------+
+   * | Shift     |RGBH-|RGBS-|RGBB-|     |     |     |     |RGBM-|RGBM+|RGBTG|  Shift  |VolUp|     |
+   * |---------------------------------------------------------------------------------------------+
+   * | Ctrl |  Win  |  Alt  |                                   | RAlt | Fn  |||||     |VolDn|     |
+   * '---------------------------------------------------------------------------------------------'
+   */
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  [_BL] = LAYOUT(
+      KC_GESC, KC_1,    KC_2,    KC_3,    KC_4,   KC_5,   KC_6,   KC_7,   KC_8,   KC_9,    KC_0,    KC_MINS,  KC_EQL,  KC_BSPC,  KC_DEL, 
+      KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,   KC_T,   KC_Y,   KC_U,   KC_I,   KC_O,    KC_P,    KC_LBRC,  KC_RBRC, KC_BSLS,  KC_PGUP,
+      KC_CAPS, KC_A,    KC_S,    KC_D,    KC_F,   KC_G,   KC_H,   KC_J,   KC_K,   KC_L,    KC_SCLN, KC_QUOT,  KC_ENT,            KC_PGDN,
+      KC_LSFT,          KC_Z,    KC_X,    KC_C,   KC_V,   KC_B,   KC_N,   KC_M,   KC_COMM, KC_DOT,  KC_SLSH,  KC_RSFT, KC_UP,    MO(_FL),
+      KC_LCTL, KC_LGUI, KC_LALT,                          KC_SPC,                 KC_RALT, MO(_FL),           KC_LEFT, KC_DOWN,  KC_RIGHT),
+
+  [_FL] = LAYOUT(
+     /* esc      1        2        3        4       5       6       7       8       9         0        -         =     bkspc     delete */
+      KC_GRV,  KC_F1,   KC_F2,   KC_F3,   KC_F4,  KC_F5,  KC_F6,  KC_F7,  KC_F8,  KC_F9,   KC_F10,  KC_F11,   KC_F12,  KC_DEL,   KC_PSCR,
+     /*  tab      Q       W        E        R        T      Y        U      I        O        P        [         ]        \       pg up */ 
+      KC_TRNS, RGB_M_P, RGB_M_B, RGB_M_R, RESET,  KC_TRNS,KC_TRNS,KC_TRNS,KC_INS, KC_TRNS, KC_TRNS, KC_TRNS,  KC_PSCR, KC_BSLS,  KC_HOME,
+     /*  caps     A       S        D        F        G      H        J      K        L        ;        '        enter             pg dn */
+      KC_TRNS, RGB_HUI, RGB_SAI, RGB_VAI, KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS,  KC_INS,            KC_END, 
+     /* shift             Z         X        C       V       B       N      M        ,        .        /        shift     up        fn  */
+      KC_LSFT,          RGB_HUD, RGB_SAD, RGB_VAD,KC_TRNS,KC_TRNS,KC_TRNS,KC_MUTE,RGB_RMOD, RGB_MOD, RGB_TOG,  KC_RSFT, KC_VOLU, KC_TRNS,
+     /* ctrl     win      alt                              space                    alt      fn                 left     down     right */
+      KC_LCTL, KC_LGUI, KC_LALT,                          KC_TRNS,                KC_RALT, KC_TRNS,           KC_TRNS, KC_VOLD,  KC_TRNS)
+};

keyboards/coseyfannitutti/mullet/keymaps/default/keymap.c

@@ -0,0 +1,68 @@
+/* Copyright 2019 COSEYFANNITUTTI
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+#define _BL 0
+#define _FL 1
+
+  /* Qwerty
+   * .---------------------------------------------------------------------------------------------.
+   * | Esc |  1  |  2  |  3  |  4  |  5  |  6  |  7  |  8  |  9  |  0  |  -  |  =  |  Bkspc  | Ins |
+   * |---------------------------------------------------------------------------------------------+
+   * | Tab    |  Q  |  W  |  E  |  R  |  T  |  Y  |  U  |  I  |  O  |  P  |  [  |  ]  |   \  | Del |
+   * |---------------------------------------------------------------------------------------------+
+   * | Caps    |  A  |  S  |  D  |  F  |  G  |  H  |  J  |  K  |  L  |  ;  |  '  |   Enter   | PgUp|
+   * |---------------------------------------------------------------------------------------------+
+   * | Shift     |  Z  |  X  |  C  |  V  |  B  |  N  |  M  |  ,  |  .  |  /  |  Shift  |  U  | Pgdn|
+   * |---------------------------------------------------------------------------------------------+
+   * | Ctrl |  Win  |  Alt  |              Space                | RAlt | FN  |||||  L  |  D  |  R  |
+   * '---------------------------------------------------------------------------------------------'
+   */
+
+  /* FnLayer
+   * .---------------------------------------------------------------------------------------------.
+   * | ` ~ |  F1 |  F2 |  F3 |  F4 |  F5 |  F6 |  F7 |  F8 |  F9 | F10 | F11 | F12 |  DELETE |PNTSC|
+   * |---------------------------------------------------------------------------------------------+
+   * | Tab    |STATC|BRTHE|RNBOW|RESET|     |     |     |     |     |     |PAUSE|     |  \   |     |
+   * |---------------------------------------------------------------------------------------------+
+   * | Caps    |RGBH+|RGBS+|RGBB+|     |     |     |     |     |     |     | INS |    Enter  | HOME|
+   * |---------------------------------------------------------------------------------------------+
+   * | Shift     |RGBH-|RGBS-|RGBB-|     |     |     |     |RGBM-|RGBM+|RGBTG|  Shift  |VOLUP| END |
+   * |---------------------------------------------------------------------------------------------+
+   * | Ctrl |  Win  |  Alt  |                                   | RAlt | FN  |||||  L  |VOLDN|  R  |
+   * '---------------------------------------------------------------------------------------------'
+   */
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  [_BL] = LAYOUT(
+      KC_GESC, KC_1,    KC_2,    KC_3,    KC_4,   KC_5,   KC_6,   KC_7,   KC_8,   KC_9,    KC_0,    KC_MINS,  KC_EQL,  KC_BSPC,  KC_INS,
+      KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,   KC_T,   KC_Y,   KC_U,   KC_I,   KC_O,    KC_P,    KC_LBRC,  KC_RBRC, KC_BSLS,  KC_DEL,
+      KC_CAPS, KC_A,    KC_S,    KC_D,    KC_F,   KC_G,   KC_H,   KC_J,   KC_K,   KC_L,    KC_SCLN, KC_QUOT,  KC_ENT,            KC_PGUP,
+      KC_LSFT,          KC_Z,    KC_X,    KC_C,   KC_V,   KC_B,   KC_N,   KC_M,   KC_COMM, KC_DOT,  KC_SLSH,  KC_RSFT, KC_UP,    KC_PGDN,
+      KC_LCTL, KC_LGUI, KC_LALT,                          KC_SPC,                 KC_RALT, MO(_FL),           KC_LEFT, KC_DOWN,  KC_RIGHT),
+
+  [_FL] = LAYOUT(
+     /* esc      1        2        3        4       5       6       7       8       9         0        -         =     bkspc     insert*/
+      KC_GRV,  KC_F1,   KC_F2,   KC_F3,   KC_F4,  KC_F5,  KC_F6,  KC_F7,  KC_F8,  KC_F9,   KC_F10,  KC_F11,   KC_F12,  KC_DEL,   KC_PSCR,
+     /*  tab      Q       W        E        R        T      Y        U      I        O        P        [         ]        \      delete*/ 
+      KC_TRNS, RGB_M_P, RGB_M_B, RGB_M_R, RESET,  KC_TRNS,KC_TRNS,KC_TRNS,KC_INS, KC_TRNS, KC_TRNS, KC_TRNS,  KC_PAUS, KC_BSLS,  KC_TRNS,
+     /*  caps     A       S        D        F        G      H        J      K        L        ;        '        enter             pg up*/
+      KC_TRNS, RGB_HUI, RGB_SAI, RGB_VAI, KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS,  KC_INS,            KC_HOME,
+     /* shift             Z         X        C       V       B       N      M        ,        .        /        shift     up      pg dn*/
+      KC_LSFT,          RGB_HUD, RGB_SAD, RGB_VAD,KC_TRNS,KC_TRNS,KC_TRNS,KC_MUTE,RGB_RMOD, RGB_MOD, RGB_TOG,  KC_RSFT, KC_VOLU,  KC_END,
+     /* ctrl     win      alt                              space                    alt      fn                 left     down     right*/
+      KC_LCTL, KC_LGUI, KC_LALT,                          KC_TRNS,                KC_RALT, KC_TRNS,           KC_TRNS, KC_VOLD,  KC_TRNS)
+};

keyboards/coseyfannitutti/mullet/mullet.c

@@ -0,0 +1,23 @@
+/* Copyright 2019 COSEYFANNITUTTI
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "mullet.h"
+
+void matrix_init_kb(void) {
+	// put your keyboard start-up code here
+	// runs once when the firmware starts up
+
+	matrix_init_user();
+}

keyboards/coseyfannitutti/mullet/mullet.h

@@ -0,0 +1,42 @@
+/* Copyright 2019 COSEYFANNITUTTI
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+#define _x_ KC_NO
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+#define LAYOUT( \
+  K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, K0E, \
+  K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, K1E, \
+  K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B,      K2D, K2E, \
+  K30,      K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, K3E, \
+  K40, K41, K42,                K46,                K4A, K4B, K4C, K4D, K4E \
+) { \
+{ K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, K0E }, \
+{ K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, K1E }, \
+{ K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, _x_, K2D, K2E }, \
+{ K30, _x_, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, K3E }, \
+{ K40, K41, K42, _x_, _x_, _x_, K46, _x_, _x_, _x_, K4A, K4B, K4C, K4D, K4E} \
+}

keyboards/coseyfannitutti/mullet/readme.md

@@ -0,0 +1,15 @@
+# mullet
+
+![mullet](https://i.imgur.com/EBOMbhH.jpg)
+
+A 68 key keyboard with USB Type-C and RGB underglow
+
+Keyboard Maintainer: [coseyfannitutti](https://github.com/coseyfannitutti)  
+Hardware Supported: Mullet, atmega32u4  
+Hardware Availability: https://github.com/coseyfannitutti/mullet
+
+Make example for this keyboard (after setting up your build environment):
+
+    make coseyfannitutti/mullet:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/coseyfannitutti/mullet/rules.mk

@@ -0,0 +1,80 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   atmega32a    bootloadHID
+BOOTLOADER = atmel-dfu
+
+
+# If you don't know the bootloader type, then you can specify the
+# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
+#   Teensy halfKay      512
+#   Teensy++ halfKay    1024
+#   Atmel DFU loader    4096
+#   LUFA bootloader     4096
+#   USBaspLoader        2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = lite    # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes        # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = yes        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)

keyboards/coseyfannitutti/mulletpad/config.h

@@ -0,0 +1,172 @@
+/*
+Copyright 2019 COSEYFANNITUTTI
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6666
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    coseyfannitutti
+#define PRODUCT         mulletpad
+#define DESCRIPTION     numpad
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 4
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { F4, F1, F5, F6, F7 }
+#define MATRIX_COL_PINS { F0, C7, C6, B6, }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */
+#define DIODE_DIRECTION COL2ROW
+
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+//#define RGB_DI_PIN D5
+//#ifdef RGB_DI_PIN
+//#define RGBLIGHT_ANIMATIONS
+//#define RGBLED_NUM 8
+//#define RGBLIGHT_HUE_STEP 8
+//#define RGBLIGHT_SAT_STEP 8
+//#define RGBLIGHT_VAL_STEP 8
+//#define RGBLIGHT_SLEEP
+//#endif
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+//#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+//#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
+#endif
+*/
+

keyboards/coseyfannitutti/mulletpad/info.json

@@ -0,0 +1,12 @@
+{
+    "keyboard_name": "mulletpad", 
+    "url": "https://github.com/coseyfannitutti/mulletpad", 
+    "maintainer": "coseyfannitutti", 
+    "width": 4, 
+    "height": 5, 
+    "layouts": {
+        "LAYOUT": {
+            "layout": [{"label":"Num Lock", "x":0, "y":0}, {"label":"/", "x":1, "y":0}, {"label":"*", "x":2, "y":0}, {"label":"-", "x":3, "y":0}, {"label":"7", "x":0, "y":1}, {"label":"8", "x":1, "y":1}, {"label":"9", "x":2, "y":1}, {"label":"+", "x":3, "y":1, "h":2}, {"label":"4", "x":0, "y":2}, {"label":"5", "x":1, "y":2}, {"label":"6", "x":2, "y":2}, {"label":"1", "x":0, "y":3}, {"label":"2", "x":1, "y":3}, {"label":"3", "x":2, "y":3}, {"label":"Enter", "x":3, "y":3, "h":2}, {"label":"0", "x":0, "y":4, "w":2}, {"label":".", "x":2, "y":4}]
+        }
+    }
+}

keyboards/coseyfannitutti/mulletpad/keymaps/default/keymap.c

@@ -0,0 +1,27 @@
+/* Copyright 2019 COSEYFANNITUTTI
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+#define _BL 0
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  [_BL] = LAYOUT_numpad_5x4(
+      KC_NLCK, KC_PSLS, KC_PAST, KC_PMNS, 
+      KC_P7,   KC_P8,   KC_P9,            
+      KC_P4,   KC_P5,   KC_P6,   KC_PPLS, 
+      KC_P1,   KC_P2,   KC_P3,            
+      KC_P0,   KC_PDOT,          KC_PENT  )
+};

keyboards/coseyfannitutti/mulletpad/mulletpad.c

@@ -0,0 +1,23 @@
+/* Copyright 2019 COSEYFANNITUTTI
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "mulletpad.h"
+
+void matrix_init_kb(void) {
+	// put your keyboard start-up code here
+	// runs once when the firmware starts up
+
+	matrix_init_user();
+}

keyboards/coseyfannitutti/mulletpad/mulletpad.h

@@ -0,0 +1,42 @@
+/* Copyright 2019 COSEYFANNITUTTI
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+#define _x_ KC_NO
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+#define LAYOUT_numpad_5x4( \
+  K00, K01, K02, K03, \
+  K10, K11, K12,      \
+  K20, K21, K22, K23, \
+  K30, K31, K32,      \
+  K40,      K42, K43  \
+) { \
+{ K00, K01, K02, K03, }, \
+{ K10, K11, K12, _x_, }, \
+{ K20, K21, K22, K23, }, \
+{ K30, K31, K32, _x_, }, \
+{ K40, _x_, K42, K43, }, \
+}

keyboards/coseyfannitutti/mulletpad/readme.md

@@ -0,0 +1,15 @@
+# mulletpad
+
+![mulletpad](https://i.imgur.com/MHKo5f5.png)
+
+A 17-key numpad with USB Type-C.
+
+Keyboard Maintainer: [coseyfannitutti](https://github.com/coseyfannitutti)  
+Hardware Supported: Mulletpad, atmega32u4  
+Hardware Availability: https://github.com/coseyfannitutti/mulletpad
+
+Make example for this keyboard (after setting up your build environment):
+
+    make coseyfannitutti/mulletpad:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/coseyfannitutti/mulletpad/rules.mk

@@ -0,0 +1,82 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   atmega32a    bootloadHID
+BOOTLOADER = atmel-dfu
+
+
+# If you don't know the bootloader type, then you can specify the
+# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
+#   Teensy halfKay      512
+#   Teensy++ halfKay    1024
+#   Atmel DFU loader    4096
+#   LUFA bootloader     4096
+#   USBaspLoader        2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes        # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
+
+LAYOUTS = numpad_5x4

keyboards/crkbd/keymaps/drashna/config.h

@@ -48,17 +48,24 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #ifdef RGB_MATRIX_ENABLE
 #   define RGB_MATRIX_KEYPRESSES // reacts to keypresses
 #   define RGB_DISABLE_WHEN_USB_SUSPENDED true // turn off effects when suspended
+#   define RGB_MATRIX_FRAMEBUFFER_EFFECTS
 
+// #   define DISABLE_RGB_MATRIX_ALPHAS_MODS
 #   define DISABLE_RGB_MATRIX_GRADIENT_UP_DOWN
+#   define DISABLE_RGB_MATRIX_BREATHING
 #   define DISABLE_RGB_MATRIX_CYCLE_ALL
+#   define DISABLE_RGB_MATRIX_CYCLE_LEFT_RIGHT
 #   define DISABLE_RGB_MATRIX_CYCLE_UP_DOWN
+// #   define DISABLE_RGB_MATRIX_CYCLE_OUT_IN
+// #   define DISABLE_RGB_MATRIX_CYCLE_OUT_IN_DUAL
 #   define DISABLE_RGB_MATRIX_RAINBOW_MOVING_CHEVRON
 #   define DISABLE_RGB_MATRIX_DUAL_BEACON
 #   define DISABLE_RGB_MATRIX_RAINBOW_BEACON
 #   define DISABLE_RGB_MATRIX_RAINBOW_PINWHEELS
-// #define DISABLE_RGB_MATRIX_RAINDROPS
-// #define DISABLE_RGB_MATRIX_JELLYBEAN_RAINDROPS
-#   define DISABLE_RGB_MATRIX_DIGITAL_RAIN
+// #   define DISABLE_RGB_MATRIX_RAINDROPS
+// #   define DISABLE_RGB_MATRIX_JELLYBEAN_RAINDROPS
+// #   define DISABLE_RGB_MATRIX_TYPING_HEATMAP
+// #   define DISABLE_RGB_MATRIX_DIGITAL_RAIN
 #   define DISABLE_RGB_MATRIX_SOLID_REACTIVE
 #   define DISABLE_RGB_MATRIX_SOLID_REACTIVE_SIMPLE
 #   define DISABLE_RGB_MATRIX_SOLID_REACTIVE_WIDE
@@ -67,8 +74,11 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #   define DISABLE_RGB_MATRIX_SOLID_REACTIVE_MULTICROSS
 #   define DISABLE_RGB_MATRIX_SOLID_REACTIVE_NEXUS
 #   define DISABLE_RGB_MATRIX_SOLID_REACTIVE_MULTINEXUS
+#   define DISABLE_RGB_MATRIX_SPLASH
+// #   define DISABLE_RGB_MATRIX_MULTISPLASH
 #   define DISABLE_RGB_MATRIX_SOLID_SPLASH
 #   define DISABLE_RGB_MATRIX_SOLID_MULTISPLASH
+#endif
 
 #ifdef AUDIO_ENABLE
 #   define B6_AUDIO

keyboards/crkbd/keymaps/drashna/keymap.c

@@ -20,9 +20,9 @@ enum crkbd_keycodes {
   ) \
   LAYOUT_wrapper( \
     KC_ESC,  K01,    K02,     K03,      K04,     K05,                        K06,     K07,     K08,     K09,     K0A,     KC_MINS, \
-    KC_TAB, ALT_T(K11),  K12, K13,      K14,     K15,                        K16,     K17,     K18,     K19,     K1A, RGUI_T(KC_QUOT), \
+    KC_TAB, ALT_T(K11),  K12, K13,      K14,     K15,                        K16,     K17,     K18,     K19,     K1A,     KC_QUOT, \
     OS_LSFT, CTL_T(K21), K22, K23,      K24,     K25,                        K26,     K27,     K28,     K29, RCTL_T(K2A), OS_RSFT, \
-                           LT(_LOWER,KC_GRV), KC_SPC,  KC_BSPC,     KC_DEL,  KC_ENT,  RAISE                                        \
+                                        KC_GRV,  KC_SPC,  BK_LWER, DL_RAIS,  KC_ENT,  OS_RGUI                                      \
   )
 #define LAYOUT_crkbd_base_wrapper(...)       LAYOUT_crkbd_base(__VA_ARGS__)
 
@@ -100,7 +100,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
     KC_MAKE, _________________ADJUST_L1_________________,                    _________________ADJUST_R1_________________, KC_RESET,
     VRSN,    _________________ADJUST_L2_________________,                    _________________ADJUST_R2_________________, EEP_RST,
     _______, _________________ADJUST_L3_________________,                    _________________ADJUST_R3_________________, KC_MPLY,
-                                     _______, _______, _______,        KC_NUKE, TG_MODS, _______
+                                     _______, KC_NUKE, _______,        _______, TG_MODS, _______
   )
 };
 
@@ -156,6 +156,8 @@ void add_keylog(uint16_t keycode) {
     if (keycode < 60) {
         keylog_str[0] = code_to_name[keycode];
     }
+    keylog_str[KEYLOG_LEN] = 0;
+
     log_timer = timer_read();
 }
 
@@ -267,3 +269,61 @@ uint16_t get_tapping_term(uint16_t keycode) {
             return TAPPING_TERM;
     }
 }
+
+#ifdef RGB_MATRIX_ENABLE
+
+void suspend_power_down_keymap(void) {
+    rgb_matrix_set_suspend_state(true);
+}
+
+void suspend_wakeup_init_keymap(void) {
+    rgb_matrix_set_suspend_state(false);
+}
+
+void rgb_matrix_indicators_user(void) {
+    if ( userspace_config.rgb_layer_change &&
+#ifdef RGB_DISABLE_WHEN_USB_SUSPENDED
+        !g_suspend_state &&
+#endif
+#if defined(RGBLIGHT_ENABLE)
+        (!rgblight_config.enable && rgb_matrix_config.enable)
+#else
+        rgb_matrix_config.enable
+#endif
+    ) {
+        switch (biton32(layer_state)) {
+            case _MODS:
+                rgb_matrix_layer_helper(0xFF, 0xFF, 0x00, LED_FLAG_UNDERGLOW); break;
+            case _GAMEPAD:
+                rgb_matrix_layer_helper(0xFF, 0x80, 0x00, LED_FLAG_UNDERGLOW); break;
+            case _DIABLO:
+                rgb_matrix_layer_helper(0xFF, 0x00, 0x00, LED_FLAG_UNDERGLOW); break;
+            case _RAISE:
+                rgb_matrix_layer_helper(0xFF, 0xFF, 0x00, LED_FLAG_UNDERGLOW); break;
+            case _LOWER:
+                rgb_matrix_layer_helper(0x00, 0xFF, 0x00, LED_FLAG_UNDERGLOW); break;
+            case _ADJUST:
+                rgb_matrix_layer_helper(0xFF, 0x00, 0x00, LED_FLAG_UNDERGLOW); break;
+            default:
+                switch (biton32(default_layer_state)) {
+                    case _QWERTY:
+                        rgb_matrix_layer_helper(0x00, 0xFF, 0xFF, LED_FLAG_UNDERGLOW); break;
+                    case _COLEMAK:
+                        rgb_matrix_layer_helper(0xFF, 0x00, 0xFF, LED_FLAG_UNDERGLOW); break;
+                    case _DVORAK:
+                        rgb_matrix_layer_helper(0x00, 0xFF, 0x00, LED_FLAG_UNDERGLOW); break;
+                    case _WORKMAN:
+                        rgb_matrix_layer_helper(0xD9, 0xA5, 0x21, LED_FLAG_UNDERGLOW); break;
+                    case _NORMAN:
+                        rgb_matrix_layer_helper(0xFF, 0x7C, 0x4D, LED_FLAG_UNDERGLOW); break;
+                    case _MALTRON:
+                        rgb_matrix_layer_helper(0xFF, 0xFF, 0x00, LED_FLAG_UNDERGLOW); break;
+                    case _EUCALYN:
+                        rgb_matrix_layer_helper(0xFF, 0x80, 0xBF, LED_FLAG_UNDERGLOW); break;
+                    case _CARPLAX:
+                        rgb_matrix_layer_helper(0x00, 0x00, 0xFF, LED_FLAG_UNDERGLOW); break;
+                }
+        }
+    }
+}
+#endif

keyboards/crkbd/ssd1306.c

@@ -13,7 +13,7 @@
 #include "sendchar.h"
 #include "timer.h"
 
-static const unsigned char font[] PROGMEM;
+extern const unsigned char font[] PROGMEM;
 
 // Set this to 1 to help diagnose early startup problems
 // when testing power-on with ble.  Turn it off otherwise,

keyboards/doro67/multi/multi.c

@@ -19,6 +19,7 @@ void matrix_init_kb(void) {
 	// put your keyboard start-up code here
 	// runs once when the firmware starts up
 
+    setPinOutput(E6);
 	matrix_init_user();
 }
 
@@ -39,5 +40,11 @@ bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
 void led_set_kb(uint8_t usb_led) {
 	// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
 
+	if (IS_LED_ON(usb_led, USB_LED_CAPS_LOCK)) {
+		writePinLow(E6);
+	} else {
+		writePinHigh(E6);
+	}
+
 	led_set_user(usb_led);
 }

keyboards/dz60/dz60.h

@@ -404,13 +404,13 @@
     k10,      k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c, k1d,      \
     k20,      k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, k1e, k2d, \
     k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b,      k3d, k3e, \
-    k40, k41,      k43, k44,      k46,      k48,      k4a, k4b, k4c, k4d, k4e  \
+    k40, k41,      k43, k44,      k46,      k48,      k4a, k4b,      k4d, k4e  \
 ) { \
     { k00,  k01,   k02,   k03,  k04,  k05,   k06,  k07,   k08,  k09,   k0a,  k0b,   k0c,  k0d,  k0e   }, \
     { k10,  KC_NO, k12,   k13,  k14,  k15,   k16,  k17,   k18,  k19,   k1a,  k1b,   k1c,  k1d,  k1e   }, \
     { k20,  KC_NO, k22,   k23,  k24,  k25,   k26,  k27,   k28,  k29,   k2a,  k2b,   k2c,  k2d,  KC_NO }, \
     { k30,  k31,   k32,   k33,  k34,  k35,   k36,  k37,   k38,  k39,   k3a,  k3b,   KC_NO,k3d,  k3e   }, \
-    { k40,  k41,   KC_NO, k43,  k44,  KC_NO, k46,  KC_NO, k48,  KC_NO, k4a,  k4b,   k4c,  k4d,  k4e   }  \
+    { k40,  k41,   KC_NO, k43,  k44,  KC_NO, k46,  KC_NO, k48,  KC_NO, k4a,  k4b,   KC_NO,k4d,  k4e   }  \
 }
 
 #endif

keyboards/dz60/keymaps/olligranlund_iso/keymap.c

@@ -26,13 +26,13 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 		KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,     KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC,
 		MO(1),   KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,     KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_BSLS, KC_ENT,
 		KC_LSFT, KC_NUBS, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,     KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT, KC_PSCR,
-		KC_LCTL, KC_LGUI, KC_LALT, KC_SPC,  KC_SPC,  KC_SPC,  KC_RALT, MO(1),    KC_NO,   KC_APP,   KC_RCTL),
+		KC_LCTL, KC_LGUI, KC_LALT, KC_SPC,  KC_SPC,  KC_SPC,  KC_RALT, MO(1),    KC_APP,  KC_RCTL),
 
 	LAYOUT_60_iso_split_space_bs_rshift(
 		KC_GRV,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,    KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_DEL,  KC_DEL,
 		KC_NO,   KC_MPRV, KC_MPLY, KC_MNXT, KC_NO,   KC_NO,   KC_NO,   KC_PGDOWN,KC_UP,   KC_PGUP, KC_NO,   KC_NO,   KC_NO,
 		KC_NO,   KC_VOLD, KC_MUTE, KC_VOLU, KC_NO,   KC_NO,   KC_HOME,  KC_LEFT, KC_DOWN, KC_RGHT, KC_NO,   KC_NO,   KC_NO,   KC_NO,
 		KC_LSFT, KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_END,   KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_RSFT, KC_CAPS,
-		KC_LCTL, KC_LGUI, KC_LALT, KC_SPC,  KC_SPC,  KC_SPC,  KC_RALT, MO(1),    KC_NO,   KC_APP,  KC_RCTL),
+		KC_LCTL, KC_LGUI, KC_LALT, KC_SPC,  KC_SPC,  KC_SPC,  KC_RALT, MO(1),    KC_APP,  KC_RCTL),
 
 };

keyboards/ergodox_ez/info.json

@@ -1,7 +1,7 @@
 {
     "keyboard_name": "ErgoDox EZ",
     "url": "ergodox-ez.com",
-    "maintainer": "erez",
+    "maintainer": "ZSA",
     "width": 17,
     "height": 8,
 

keyboards/ergodox_ez/keymaps/pvinis/keymap.c

@@ -0,0 +1,330 @@
+// pvinis ergodox ez
+// ,------------------------------------.          ,------------------------------------.
+// |      |    |    |    |    |    |    |          |    |    |    |    |    |    |      |
+// |------+----+----+----+----+---------|          |----+----+----+----+----+----+------|
+// |      |    |    |    |    |    |    |          |    |    |    |    |    |    |      |
+// |------+----+----+----x----x----|    |          |    |----x----x----+----+----+------|
+// |      |    |    |    |    |    |----|          |----|    |    |    |    |    |      |
+// |------+----+----+----x----x----|    |          |    |----x----x----+----+----+------|
+// |      |    |    |    |    |    |    |          |    |    |    |    |    |    |      |
+// `------+----+----+----+----+---------'          `---------+----+----+----+----+------'
+//   |    |    |    |    |    |                              |    |    |    |    |    |
+//   `------------------------'                              `------------------------'
+//                              ,---------.      ,---------.
+//                              |    |    |      |    |    |
+//                         ,----+----+----|      |----+----+----.
+//                         |    |    |    |      |    |    |    |
+//                         |    |    |----|      |----|    |    |
+//                         |    |    |    |      |    |    |    |
+//                         `--------------'      `--------------'
+
+
+#include QMK_KEYBOARD_H
+#include "pvinis.h"
+#include "mousekey.h"
+
+
+// layers
+enum {
+  MOUSE = 8,
+};
+
+// extra keys
+enum {
+  NONE = 30,
+  TD_LAYR, // SYSCTL and MOUSE layer switch
+};
+
+// application selection
+// this is sending ctrl-alt-gui-<key>, and this is picked up by hammerspoon
+#define AP_SLCK ALLM(KC_S)
+#define AP_XCOD ALLM(KC_X)
+#define AP_MSGR ALLM(KC_M)
+
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  // ,------------------------------------.          ,------------------------------------.
+  // |4xFLSH|    |    |    |    |    |Opt |          |    |    |    |    |    |    |      |
+  // |------+----+----+----+----+---------|          |----+----+----+----+----+----+------|
+  // | Tab  |    |    |    |    |    |    |          |    |    |    |    |    |    |      |
+  // |------+----+----+----x----x----|    |          |    |----x----x----+----+----+------|
+  // |EscCtl|    |    |    |    |    |----|          |----|    |    |    |    |    | Ent  |
+  // |------+----+----+----x----x----|    |          |    |----x----x----+----+----+------|
+  // |LShift|    |    |    |    |    |    |          |    |    |    |    |    |    |RShift|
+  // `------+----+----+----+----+---------'          `---------+----+----+----+----+------'
+  //   |    |    |    |    |Cmd |                              |    |    |    |    |    |
+  //   `------------------------'                              `------------------------'
+  //                              ,---------.      ,---------.
+  //                              |QWER|    |      |    |    |
+  //                         ,----+----+----|      |----+----+----.
+  //                         | Ba | L  |    |      |    |    |    |
+  //                         | ck |Shi |----|      |----|    |Spc |
+  //                         | spc| ft |    |      |    |    |    |
+  //                         `--------------'      `--------------'
+  [LR_BASE] = LAYOUT_ergodox_pretty_wrapper(
+    TD_3FLS, _______, _______, _______, _______, _______, KC_LALT,      _______, _______, _______, _______, _______, _______, _______,
+    KC_TAB , _______, _______, _______, _______, _______, _______,      _______, _______, _______, _______, _______, _______, _______,
+    PV_ESCC, _______, _______, _______, _______, _______,                        _______, _______, _______, _______, _______, KC_ENT ,
+    KC_LSFT, _______, _______, _______, _______, _______, _______,      _______, _______, _______, _______, _______, _______, KC_RSFT,
+    _______, _______, _______, KC_LGUI, SYMBOL ,                                          SYSCTL , KC_RALT, _______, _______, _______,
+                                                 QWERTY , CARPALX,      _______, _______,
+                                                          _______,      _______,
+                                        KC_BSPC, _______, _______,      _______, _______, KC_SPC
+  ),
+
+  // ,------------------------------------.          ,------------------------------------.
+  // |      |        NUMBERS_L       |    |          |  - |        NUMBERS_R       |  =   |
+  // |------+----+----+----+----+---------|          |----+----+----+----+----+----+------|
+  // |      |                        |  [ |          | ]  |                        |      |
+  // |------+                        |    |          |    |                        +------|
+  // |      |         QWERTY_L       |----|          |----|         QWERTY_R       |      |
+  // |------+                        |  ( |          | )  |                        +------|
+  // |      |                        |    |          |    |                        |      |
+  // `------+----+----+----+----+---------'          `---------+----+----+----+----+------'
+  //   |    | `  |    |    |    |                              |    |    |    |  ' |    |
+  //   `------------------------'                              `------------------------'
+  //                              ,---------.      ,---------.
+  //                              |    |    |      |    |    |
+  //                         ,----+----+----|      |----+----+----.
+  //                         |    |    |    |      |    |    |    |
+  //                         |    |    |----|      |----|    |    |
+  //                         |    |    |    |      |    |    |    |
+  //                         `--------------'      `--------------'
+  // See `users/pvinis/pvinis.h`
+  [LR_QWERTY] = LAYOUT_ergodox_pretty_wrapper(
+    _______, ________________NUMBERS_L__________________, _______,      KC_MINS, ________________NUMBERS_R__________________, KC_EQL ,
+    _______, _________________QWERTY_L1_________________, KC_LBRC,      KC_RBRC, _________________QWERTY_R1_________________, _______,
+    _______, _________________QWERTY_L2_________________,                        _________________QWERTY_R2_________________, _______,
+    _______, _________________QWERTY_L3_________________, KC_LPRN,      KC_RPRN, _________________QWERTY_R3_________________, _______,
+    _______, KC_GRV, _______, _______, _______,                                          _______, _______, _______, KC_QUOT , _______,
+                                                 _______, _______,      _______, _______,
+                                                          _______,      _______,
+                                        _______, _______, _______,      _______, _______, _______
+  ),
+
+  // ,------------------------------------.          ,------------------------------------.
+  // |      |        NUMBERS_L       |    |          |    |        NUMBERS_R       |      |
+  // |------+----+----+----+----+---------|          |----+----+----+----+----+----+------|
+  // |      |                        |    |          |    |                        |      |
+  // |------+                        |    |          |    |                        +------|
+  // |      |        CARPALX_L       |----|          |----|        CARPALX_R       |      |
+  // |------+                        |    |          |    |                        +------|
+  // |      |                        |    |          |    |                        |      |
+  // `------+----+----+----+----+---------'          `---------+----+----+----+----+------'
+  //   |    |    |    |    |    |                              |    |    |    |    |    |
+  //   `------------------------'                              `------------------------'
+  //                              ,---------.      ,---------.
+  //                              |    |    |      |    |    |
+  //                         ,----+----+----|      |----+----+----.
+  //                         |    |    |    |      |    |    |    |
+  //                         |    |    |----|      |----|    |    |
+  //                         |    |    |    |      |    |    |    |
+  //                         `--------------'      `--------------'
+  // See `users/pvinis/pvinis.h`
+  [LR_CARPALX] = LAYOUT_ergodox_pretty_wrapper(
+    _______, ________________NUMBERS_L__________________, _______,      _______, ________________NUMBERS_R__________________, _______,
+    _______, ________________CARPALX_L1_________________, _______,      _______, ________________CARPALX_R1_________________, _______,
+    _______, ________________CARPALX_L2_________________,                        ________________CARPALX_R2_________________, _______,
+    _______, ________________CARPALX_L3_________________, _______,      _______, ________________CARPALX_R3_________________, _______,
+    _______, _______, _______, _______, _______,                                          _______, _______, _______, _______, _______,
+                                                 _______, _______,      _______, _______,
+                                                          _______,      _______,
+                                        _______, _______, _______,      _______, _______, _______
+  ),
+
+  // See `users/pvinis/pvinis.h`
+  [LR_SYMBOL] = LAYOUT_ergodox_pretty_wrapper(
+    _______, ______________________F_L__________________, KC_F11 ,      KC_F12 , ______________________F_R__________________, _______,
+    _______, _________________SYMBOL_L1_________________, _______,      _______, _________________SYMBOL_R1_________________, _______,
+    _______, _________________SYMBOL_L2_________________,                        _________________SYMBOL_R2_________________, _______,
+    _______, _________________SYMBOL_L3_________________, _______,      _______, _________________SYMBOL_R3_________________, _______,
+    _______, _______, _______, _______, _______,                                          _______, _______, _______, _______, _______,
+                                                 _______, _______,      _______, _______,
+                                                          _______,      _______,
+                                        _______, _______, _______,      _______, _______, _______
+  ),
+
+  // See `users/pvinis/pvinis.h`
+  [LR_SYSCTL] = LAYOUT_ergodox_pretty_wrapper(
+    _______, _______, _______, _______, _______, _______, _______,      _______, _______, _______, _______, _______, _______, _______,
+    _______, _______, _______, _______, _______, _______, _______,      _______, _________________SYSCTL_R1_________________, _______,
+    _______, _______, _______, _______, _______, _______,                        _________________SYSCTL_R2_________________, _______,
+    _______, _______, _______, _______, _______, _______, _______,      _______, _________________SYSCTL_R3_________________, _______,
+    _______, _______, _______, _______, _______,                                          _______, _______, _______, _______, _______,
+
+                                                 _______, _______,      _______, _______,
+                                                          _______,      _______,
+                                        _______, _______, _______,      _______, _______, _______
+  ),
+
+  // See `users/pvinis/pvinis.h`
+  [LR_KBCTL] = LAYOUT_ergodox_pretty_wrapper(
+    XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,      XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,
+    XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,      XXXXXXX, __________________KBCTL_R1_________________, XXXXXXX,
+    XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,                        __________________KBCTL_R2_________________, XXXXXXX,
+    XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,      XXXXXXX, __________________KBCTL_R3_________________, XXXXXXX,
+    XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, _______,                                          _______, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,
+
+                                                 XXXXXXX, XXXXXXX,      XXXXXXX, XXXXXXX,
+                                                          XXXXXXX,      XXXXXXX,
+                                        XXXXXXX, XXXXXXX, XXXXXXX,      XXXXXXX, XXXXXXX, XXXXXXX
+  ),
+
+/* MOUSE
+ * a keymap to control my system.
+ *
+ * ,--------------------------------------------------.           ,--------------------------------------------------.
+ * |   ^    |      |      |      |      |      |      |           |      |      |      |      |      |      |        |
+ * |--------+------+------+------+------+-------------|           |------+------+------+------+------+------+--------|
+ * |        |      |      |      |      |      |      |           |      |      |      | MsUp |      |      |        |
+ * |--------+------+------+------+------+------|      |           |      |------+------+------+------+------+--------|
+ * |        |      |      |      |      |      |------|           |------|      |MsLeft| MsDn |MsRght|      |        |
+ * |--------+------+------+------+------+------|      |           |      |------+------+------+------+------+--------|
+ * |        |      |      |      |      |      |      |           |      |      |      |      |      |      |        |
+ * `--------+------+------+------+------+-------------'           `-------------+------+------+------+------+--------'
+ *   |      |      |      |      |      |                                       |      |      |      |      |      |
+ *   `----------------------------------'                                       `----------------------------------'
+ *                                        ,-------------.       ,-------------.
+ *                                        |      |      |       |      |MidClk|
+ *                                 ,------|------|------|       |------+------+------.
+ *                                 |      |      |      |       |      |Left  |Right |
+ *                                 |      |      |------|       |------| Click| Click|
+ *                                 |      |      |  ^   |       |      |      |      |
+ *                                 `--------------------'       `--------------------'
+ */
+  [MOUSE] = LAYOUT_ergodox_pretty(
+   KC_TRNS    ,KC_NO  ,KC_NO  ,KC_NO  ,KC_NO  ,KC_NO    ,KC_NO
+  ,KC_NO      ,KC_NO  ,KC_NO  ,KC_NO  ,KC_NO  ,KC_NO    ,KC_NO
+  ,KC_NO      ,KC_NO  ,KC_NO  ,KC_NO  ,KC_NO  ,KC_NO
+  ,KC_NO      ,KC_NO  ,KC_NO  ,KC_NO  ,KC_NO  ,KC_NO    ,KC_NO
+  ,KC_NO      ,KC_NO  ,KC_NO  ,KC_NO  ,KC_NO
+
+                                                        ,KC_NO  ,KC_NO
+                                                                ,KC_NO
+                                                ,KC_NO  ,KC_NO  ,KC_TRNS
+
+                    ,KC_NO    ,KC_NO  ,KC_NO    ,KC_NO    ,KC_NO    ,KC_NO    ,KC_NO
+                    ,KC_NO    ,KC_NO  ,KC_NO    ,KC_MS_U  ,KC_NO    ,KC_NO    ,KC_NO
+                              ,KC_NO  ,KC_MS_L  ,KC_MS_D  ,KC_MS_R  ,KC_NO    ,KC_NO
+                    ,KC_NO    ,KC_NO  ,KC_NO    ,KC_NO    ,KC_NO    ,KC_NO    ,KC_NO
+                                      ,KC_NO    ,KC_NO    ,KC_NO    ,KC_NO    ,KC_NO
+
+            ,KC_NO  ,KC_NO
+            ,KC_NO
+            ,KC_NO  ,KC_NO  ,KC_NO
+  ),
+};
+
+
+// keyboard initialization
+void keyboard_post_init_user_local(void) {
+  ergodox_led_all_on();
+  for (int i = LED_BRIGHTNESS_HI; i > LED_BRIGHTNESS_LO; i--) {
+    ergodox_led_all_set(i);
+    wait_ms(5);
+  }
+  wait_ms(1000);
+  for (int i = LED_BRIGHTNESS_LO; i > 0; i--) {
+    ergodox_led_all_set(i);
+    wait_ms(10);
+  }
+  ergodox_led_all_off();
+
+  // restore default brightness for future use
+  ergodox_led_all_set(LED_BRIGHTNESS_HI);
+}
+
+// light up leds based on the layer
+uint32_t layer_state_set_user_local(uint32_t state) {
+  ergodox_right_led_1_off();
+  ergodox_right_led_2_off();
+  ergodox_right_led_3_off();
+  switch (biton32(state)) {
+  case LR_SYSCTL:
+    ergodox_right_led_3_on(); // blue
+    break;
+  case LR_KBCTL:
+    ergodox_right_led_1_on(); // red
+    break;
+  case LR_SYMBOL:
+    ergodox_right_led_2_on(); // green
+    break;
+  default: break;
+  }
+  return state;
+}
+
+// extra keys
+// const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) {
+  // switch (id) {
+  // }
+  // return MACRO_NONE;
+// }
+
+// tap dances
+
+// flash keyboard on 4x tap, with leds
+// void flash_each_tap(qk_tap_dance_state_t *state, void *user_data) {
+//   switch (state->count) {
+//   case 1:
+//     ergodox_right_led_3_on();
+//     break;
+//   case 2:
+//     ergodox_right_led_2_on();
+//     break;
+//   case 3:
+//     ergodox_right_led_1_on();
+//     break;
+//   case 4:
+//     ergodox_right_led_3_off();
+//     wait_ms(50);
+//     ergodox_right_led_2_off();
+//     wait_ms(50);
+//     ergodox_right_led_1_off();
+//     break;
+//   }
+// }
+
+// void flash_dance_finished(qk_tap_dance_state_t *state, void *user_data) {
+//   if (state->count >= 4) {
+//     reset_keyboard();
+//     reset_tap_dance(state);
+//   }
+// }
+
+// void flash_dance_reset(qk_tap_dance_state_t *state, void *user_data) {
+//   ergodox_right_led_1_off();
+//   wait_ms(50);
+//   ergodox_right_led_2_off();
+//   wait_ms(50);
+//   ergodox_right_led_3_off();
+// }
+
+// SYSCTL on first tap, MOUSE ON second tap
+// void layers_dance_finished(qk_tap_dance_state_t *state, void *user_data) {
+//   uint8_t layer = biton32(layer_state);
+
+//   switch(state->count) {
+//   case 1:
+//     switch(layer) {
+//     case LR_SYSCTL:
+//       layer_off(LR_SYSCTL);
+//       break;
+//     case MOUSE:
+//       layer_off(MOUSE);
+//       break;
+//     default:
+//       layer_on(LR_SYSCTL);
+//       break;
+//     }
+//     break;
+//   case 2:
+//     layer_on(MOUSE);
+//     break;
+//   }
+// }
+
+// qk_tap_dance_action_t tap_dance_actions[] = {
+  // [TD_FLSH] = ACTION_TAP_DANCE_FN_ADVANCED( flash_each_tap, flash_dance_finished, flash_dance_reset ),
+  // [TD_LAYR] = ACTION_TAP_DANCE_FN_ADVANCED( NULL, layers_dance_finished, NULL ),
+// };

keyboards/ergodox_ez/keymaps/pvinis/rules.mk

@@ -0,0 +1 @@
+TAP_DANCE_ENABLE = yes

keyboards/ergodox_ez/matrix.c

@@ -1,9 +1,5 @@
 /*
 
-Note for ErgoDox EZ customizers: Here be dragons!
-This is not a file you want to be messing with.
-All of the interesting stuff for you is under keymaps/ :)
-Love, Erez
 
 Copyright 2013 Oleg Kostyuk <cub.uanic@gmail.com>
 
@@ -95,7 +91,7 @@ void matrix_init(void) {
   // initialize matrix state: all keys off
   for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
     matrix[i]     = 0;
-    raw_matrix[i] = 0;    
+    raw_matrix[i] = 0;
   }
 
 #ifdef DEBUG_MATRIX_SCAN_RATE
@@ -168,7 +164,7 @@ uint8_t matrix_scan(void) {
 #ifdef LEFT_LEDS
   mcp23018_status = ergodox_left_leds_update();
 #endif  // LEFT_LEDS
-  bool changed = false;  
+  bool changed = false;
   for (uint8_t i = 0; i < MATRIX_ROWS_PER_SIDE; i++) {
     // select rows from left and right hands
     uint8_t left_index = i;
@@ -178,13 +174,13 @@ uint8_t matrix_scan(void) {
 
     // we don't need a 30us delay anymore, because selecting a
     // left-hand row requires more than 30us for i2c.
-    
+
     changed |= store_raw_matrix_row(left_index);
     changed |= store_raw_matrix_row(right_index);
 
     unselect_rows();
   }
-  
+
   debounce(raw_matrix, matrix, MATRIX_ROWS, changed);
   matrix_scan_quantum();
 

keyboards/ergotaco/matrix.c

@@ -1,8 +1,4 @@
 /*
-Note for ErgoDox EZ customizers: Here be dragons!
-This is not a file you want to be messing with.
-All of the interesting stuff for you is under keymaps/ :)
-Love, Erez
 
 Copyright 2013 Oleg Kostyuk <cub.uanic@gmail.com>
 
@@ -226,8 +222,8 @@ uint8_t matrix_scan(void)
     matrix_scan_quantum();
 
 #ifdef DEBUG_MATRIX
-    for (uint8_t c = 0; c < MATRIX_COLS; c++) 
-		for (uint8_t r = 0; r < MATRIX_ROWS; r++) 
+    for (uint8_t c = 0; c < MATRIX_COLS; c++)
+		for (uint8_t r = 0; r < MATRIX_ROWS; r++)
 		  if (matrix_is_on(r, c)) xprintf("r:%d c:%d \n", r, c);
 #endif
 
@@ -324,10 +320,10 @@ static void unselect_rows(void)
 static void select_row(uint8_t row)
 {
     if (row < 6) {
-        // select on mcp23018 
+        // select on mcp23018
         if (mcp23018_status) { // do nothing on error
 			// Read using bitmask
-        } else { // set active row low  : 0 // set other rows hi-Z : 1 
+        } else { // set active row low  : 0 // set other rows hi-Z : 1
             mcp23018_status = i2c_start(I2C_ADDR_WRITE, ERGODOX_EZ_I2C_TIMEOUT);        if (mcp23018_status) goto out;
             mcp23018_status = i2c_write(GPIOA, ERGODOX_EZ_I2C_TIMEOUT);                 if (mcp23018_status) goto out;
             mcp23018_status = i2c_write(~(1<<row), ERGODOX_EZ_I2C_TIMEOUT);      		if (mcp23018_status) goto out;

keyboards/exclusive/e6v2/oe_bmc/config.h

@@ -22,7 +22,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define PRODUCT_ID      0x0000
 #define DEVICE_VER      0x0001
 #define MANUFACTURER    exclusive
-#define PRODUCT         e6v2 bmc
+#define PRODUCT         e6v2 oe bmc
 #define DESCRIPTION     A custom 60% keyboard
 
 /* key matrix size */

keyboards/exclusive/e6v2/oe_bmc/oe_bmc.c

@@ -13,7 +13,7 @@
  * You should have received a copy of the GNU General Public License
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  */
-#include "bmc.h"
+#include "oe_bmc.h"
 #include "rgblight.h"
 #include "i2c_master.h"
 

keyboards/exclusive/e6v2/oe_bmc/readme.md

@@ -1,6 +1,6 @@
-# E6-V2 Bootmapper Client (ps2avrgb)
+# E6-V2 Bootmapper Client (ps2avrgb) OE
 
-These docs are for the BMC version of the E6-V2 PCB which has an atmega32a microcontroller. Please do not flash this `.hex` file on your atmega32u4 equipped E6-V2. 
+These docs are for the BMC version of the E6-V2 PCB sold during Round 1 which has an atmega32a microcontroller. Please do not flash this `.hex` file on your atmega32u4 equipped E6-V2 or your E6V2 BMC from Round 2. 
 
 Keyboard Maintainer: [MechMerlin](https://github.com/mechmerlin)  
 Hardware Supported: ps2avrgb E6-V2 with atmega32a microcontroller  
@@ -8,7 +8,7 @@ Hardware Availability: [geekhack.org/index.php?topic=90787.0](https://geekhack.o
 
 Make example for this keyboard (after setting up your build environment):
 
-    make exclusive/e6v2/bmc:default
+    make exclusive/e6v2/oe_bmc:default
 
 Flashing
 

keyboards/exclusive/e6v2/readme.md

@@ -13,7 +13,7 @@ The E6-V2 is a 60% keyboard manufactured by Exclusive.
 
 These docs are for the QMK version of the E6-V2 PCB. [More info on qmk.fm](http://qmk.fm/)
 
-The E6V2 has been available with either a bootmapper client or QMK powered PCB. During the second round, the QMK powered PCB was redesigned and used different ports and a different switch matrix. 
+The E6V2 has been available with either a Bootmapper Client or QMK-powered PCB. During the second round, the QMK-powered and BMC PCBs were redesigned, and used different ports and a different switch matrix. 
 
 Please use the appropriate version when making your firmware. Flashing one in place of the other, can brick your PCB. Please be certain whether you have a OE or LE  PCB. 
 

keyboards/foxlab/leaf60/hotswap/config.h

@@ -0,0 +1,229 @@
+/*
+Copyright 2019 Fox Lab
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x0000
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Fox Lab
+#define PRODUCT         Leaf60 Hotswap
+#define DESCRIPTION     A custom hotswap 60% keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 15
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { D2, D1, D0, D3, D5 }
+#define MATRIX_COL_PINS { F5, F4, F1, F0, B0, F6, F7, C7, C6, B6, B5, B4, D7, D6, D4 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL*/
+#define DIODE_DIRECTION COL2ROW
+
+#define BACKLIGHT_PIN B7
+#define BACKLIGHT_BREATHING
+#define BACKLIGHT_LEVELS 4
+
+#define RGB_DI_PIN E2
+#ifdef RGB_DI_PIN
+  #define RGBLED_NUM 8
+  #define RGBLIGHT_HUE_STEP 8
+  #define RGBLIGHT_SAT_STEP 8
+  #define RGBLIGHT_VAL_STEP 8
+  #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
+/*== all animations enable ==*/
+  #define RGBLIGHT_ANIMATIONS
+#endif
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+/* defined by default; to change, uncomment and set to the combination you want */
+// #define IS_COMMAND() (get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP           H
+//#define MAGIC_KEY_HELP_ALT       SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER0_ALT     GRAVE
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     B
+//#define MAGIC_KEY_BOOTLOADER_ALT ESC
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_EEPROM_CLEAR   BSPACE
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
+#endif
+*/
+
+/* Bootmagic Lite key configuration */
+// #define BOOTMAGIC_LITE_ROW 0
+// #define BOOTMAGIC_LITE_COLUMN 0

keyboards/foxlab/leaf60/hotswap/hotswap.c

@@ -0,0 +1,59 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "hotswap.h"
+
+// Optional override functions below.
+// You can leave any or all of these undefined.
+// These are only required if you want to perform custom actions.
+
+void matrix_init_kb(void) {
+  // put your keyboard start-up code here
+  // runs once when the firmware starts up
+  setPinOutput(E6);
+  matrix_init_user();
+}
+/*
+
+void matrix_scan_kb(void) {
+  // put your looping keyboard code here
+  // runs every cycle (a lot)
+
+  matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+  // put your per-action keyboard code here
+  // runs for every action, just before processing by the firmware
+
+  return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+  // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+  led_set_user(usb_led);
+}
+
+*/
+
+void led_set_kb(uint8_t usb_led) {
+  if (IS_LED_ON(usb_led, USB_LED_CAPS_LOCK)) {
+    writePinLow(E6);
+  } else {
+    writePinHigh(E6);
+  }
+	led_set_user(usb_led);
+}

keyboards/foxlab/leaf60/hotswap/hotswap.h

@@ -0,0 +1,40 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+#define LAYOUT_60_tsangan_hhkb( \
+	K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \
+	K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113,       \
+	K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212,             \
+	K300,       K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313,       \
+	K400, K401, K402,                         K407,                   K411, K412, K413  \
+) { \
+	{ K000,  K001,  K002,  K003,  K004,  K005,  K006,  K007,  K008,  K009,  K010,  K011,  K012,  K013,  K014 }, \
+	{ K100,  K101,  K102,  K103,  K104,  K105,  K106,  K107,  K108,  K109,  K110,  K111,  K112,  K113,  KC_NO }, \
+	{ K200,  K201,  K202,  K203,  K204,  K205,  K206,  K207,  K208,  K209,  K210,  K211,  K212,  KC_NO, KC_NO }, \
+	{ K300,  KC_NO, K302,  K303,  K304,  K305,  K306,  K307,  K308,  K309,  K310,  K311,  K312,  K313,  KC_NO }, \
+	{ K400,  K401,  K402,  KC_NO, KC_NO, KC_NO, KC_NO, K407,  KC_NO, KC_NO, KC_NO, K411,  K412,  K413,  KC_NO }  \
+}

keyboards/foxlab/leaf60/hotswap/info.json

@@ -0,0 +1,12 @@
+{
+    "keyboard_name": "Fox Lab Hotswap Leaf60", 
+    "url": "", 
+    "maintainer": "qmk", 
+    "width": 15, 
+    "height": 5, 
+    "layouts": {
+        "LAYOUT_60_tsangan_hhkb": {
+            "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":0, "y":1, "w":1.5}, {"x":1.5, "y":1}, {"x":2.5, "y":1}, {"x":3.5, "y":1}, {"x":4.5, "y":1}, {"x":5.5, "y":1}, {"x":6.5, "y":1}, {"x":7.5, "y":1}, {"x":8.5, "y":1}, {"x":9.5, "y":1}, {"x":10.5, "y":1}, {"x":11.5, "y":1}, {"x":12.5, "y":1}, {"x":13.5, "y":1, "w":1.5}, {"x":0, "y":2, "w":1.75}, {"x":1.75, "y":2}, {"x":2.75, "y":2}, {"x":3.75, "y":2}, {"x":4.75, "y":2}, {"x":5.75, "y":2}, {"x":6.75, "y":2}, {"x":7.75, "y":2}, {"x":8.75, "y":2}, {"x":9.75, "y":2}, {"x":10.75, "y":2}, {"x":11.75, "y":2}, {"x":12.75, "y":2, "w":2.25}, {"x":0, "y":3, "w":2.25}, {"x":2.25, "y":3}, {"x":3.25, "y":3}, {"x":4.25, "y":3}, {"x":5.25, "y":3}, {"x":6.25, "y":3}, {"x":7.25, "y":3}, {"x":8.25, "y":3}, {"x":9.25, "y":3}, {"x":10.25, "y":3}, {"x":11.25, "y":3}, {"x":12.25, "y":3, "w":1.75}, {"x":14, "y":3}, {"x":0, "y":4, "w":1.5}, {"x":1.5, "y":4}, {"x":2.5, "y":4, "w":1.5}, {"x":4, "y":4, "w":7}, {"x":11, "y":4, "w":1.5}, {"x":12.5, "y":4}, {"x":13.5, "y":4, "w":1.5}]
+        }
+    }
+}

keyboards/foxlab/leaf60/hotswap/keymaps/default/config.h

@@ -0,0 +1,19 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here

keyboards/foxlab/leaf60/hotswap/keymaps/default/keymap.c

@@ -0,0 +1,46 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+	LAYOUT_60_tsangan_hhkb(
+		KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL,  KC_GRV, KC_BSLS,
+		KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSPC, 
+		KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, 
+		KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_DEL, 
+		KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, MO(1), KC_RALT, KC_RCTL),
+
+	LAYOUT_60_tsangan_hhkb(
+		RESET, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, KC_TRNS, 
+		KC_TRNS, BL_TOGG, BL_DEC, BL_INC, BL_STEP, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS)
+
+};
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/foxlab/leaf60/hotswap/keymaps/default/readme.md

@@ -0,0 +1 @@
+# The default keymap for Fox Lab Hotswap Leaf60

keyboards/foxlab/leaf60/hotswap/readme.md

@@ -0,0 +1,13 @@
+# Fox Lab Hotswap Leaf60 
+
+A hotswap, Tsangan-layout, gasket-mount 60% keyboard.
+
+Keyboard Maintainer: [Fox Lab](https://github.com/fox-lab), [MechMerlin](https://github.com/mechmerlin)  
+Hardware Supported: Leaf60 powered by the ATmega32U4  
+Hardware Availability: [Geekhack Group Buy](https://geekhack.org/index.php?topic=99002.0)  
+
+Make example for this keyboard (after setting up your build environment):
+
+    make foxlab/leaf60/hotswap:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/foxlab/leaf60/hotswap/rules.mk

@@ -0,0 +1,80 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   atmega32a    bootloadHID
+BOOTLOADER = atmel-dfu
+
+
+# If you don't know the bootloader type, then you can specify the
+# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
+#   Teensy halfKay      512
+#   Teensy++ halfKay    1024
+#   Atmel DFU loader    4096
+#   LUFA bootloader     4096
+#   USBaspLoader        2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = yes      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no        # Console for debug(+400)
+COMMAND_ENABLE = no        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = yes       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = yes        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)

keyboards/foxlab/leaf60/readme.md

@@ -0,0 +1,7 @@
+# Fox Lab Leaf60
+
+The Leaf60 is a 60% gasket mount board sold via [Geekhack Group Buy](https://geekhack.org/index.php?topic=99002.0).
+
+It was available with a universal layout PCB and a hotswap tsangan PCB. 
+
+**Firmware generated for one PCB will not work on the other.**

keyboards/foxlab/leaf60/universal/config.h

@@ -0,0 +1,229 @@
+/*
+Copyright 2019 Fox Lab
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x0000
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Fox Lab
+#define PRODUCT         Leaf60 Universal
+#define DESCRIPTION     A custom 60% keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 15
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { D0, D1, F0, F4, F1 }
+#define MATRIX_COL_PINS { B0, F5, F6, F7, C7, C6, B6, B5, B4, D7, D6, D4, D5, D3, D2 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL*/
+#define DIODE_DIRECTION COL2ROW
+
+#define BACKLIGHT_PIN B7
+#define BACKLIGHT_BREATHING
+#define BACKLIGHT_LEVELS 3
+
+#define RGB_DI_PIN E2
+#ifdef RGB_DI_PIN
+  #define RGBLED_NUM 8
+  #define RGBLIGHT_HUE_STEP 8
+  #define RGBLIGHT_SAT_STEP 8
+  #define RGBLIGHT_VAL_STEP 8
+  #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
+/*== all animations enable ==*/
+  #define RGBLIGHT_ANIMATIONS
+#endif
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+/* defined by default; to change, uncomment and set to the combination you want */
+// #define IS_COMMAND() (get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP           H
+//#define MAGIC_KEY_HELP_ALT       SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER0_ALT     GRAVE
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     B
+//#define MAGIC_KEY_BOOTLOADER_ALT ESC
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_EEPROM_CLEAR   BSPACE
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
+#endif
+*/
+
+/* Bootmagic Lite key configuration */
+// #define BOOTMAGIC_LITE_ROW 0
+// #define BOOTMAGIC_LITE_COLUMN 0

keyboards/foxlab/leaf60/universal/info.json

@@ -0,0 +1,20 @@
+{
+    "keyboard_name": "Fox Lab Leaf60", 
+    "url": "", 
+    "maintainer": "qmk", 
+    "width": 15, 
+    "height": 5, 
+    "layouts": {
+        "LAYOUT_all": {
+            "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":0, "y":1, "w":1.5}, {"x":1.5, "y":1}, {"x":2.5, "y":1}, {"x":3.5, "y":1}, {"x":4.5, "y":1}, {"x":5.5, "y":1}, {"x":6.5, "y":1}, {"x":7.5, "y":1}, {"x":8.5, "y":1}, {"x":9.5, "y":1}, {"x":10.5, "y":1}, {"x":11.5, "y":1}, {"x":12.5, "y":1}, {"x":13.5, "y":1, "w":1.5}, {"x":0, "y":2, "w":1.75}, {"x":1.75, "y":2}, {"x":2.75, "y":2}, {"x":3.75, "y":2}, {"x":4.75, "y":2}, {"x":5.75, "y":2}, {"x":6.75, "y":2}, {"x":7.75, "y":2}, {"x":8.75, "y":2}, {"x":9.75, "y":2}, {"x":10.75, "y":2}, {"x":11.75, "y":2}, {"x":12.75, "y":2, "w":2.25}, {"x":0, "y":3, "w":1.25}, {"x":1.25, "y":3}, {"x":2.25, "y":3}, {"x":3.25, "y":3}, {"x":4.25, "y":3}, {"x":5.25, "y":3}, {"x":6.25, "y":3}, {"x":7.25, "y":3}, {"x":8.25, "y":3}, {"x":9.25, "y":3}, {"x":10.25, "y":3}, {"x":11.25, "y":3}, {"x":12.25, "y":3, "w":1.75}, {"x":14, "y":3}, {"x":0, "y":4, "w":1.25}, {"x":1.25, "y":4, "w":1.25}, {"x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":2.25}, {"x":6, "y":4, "w":1.25}, {"x":7.25, "y":4, "w":2.75}, {"x":10, "y":4, "w":1.25}, {"x":11.25, "y":4, "w":1.25}, {"x":12.5, "y":4, "w":1.25}, {"x":13.75, "y":4, "w":1.25}]
+        },
+        
+        "LAYOUT_60_ansi": {
+            "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0, "w":2}, {"x":0, "y":1, "w":1.5}, {"x":1.5, "y":1}, {"x":2.5, "y":1}, {"x":3.5, "y":1}, {"x":4.5, "y":1}, {"x":5.5, "y":1}, {"x":6.5, "y":1}, {"x":7.5, "y":1}, {"x":8.5, "y":1}, {"x":9.5, "y":1}, {"x":10.5, "y":1}, {"x":11.5, "y":1}, {"x":12.5, "y":1}, {"x":13.5, "y":1, "w":1.5}, {"x":0, "y":2, "w":1.75}, {"x":1.75, "y":2}, {"x":2.75, "y":2}, {"x":3.75, "y":2}, {"x":4.75, "y":2}, {"x":5.75, "y":2}, {"x":6.75, "y":2}, {"x":7.75, "y":2}, {"x":8.75, "y":2}, {"x":9.75, "y":2}, {"x":10.75, "y":2}, {"x":11.75, "y":2}, {"x":12.75, "y":2, "w":2.25}, {"x":0, "y":3, "w":2.25}, {"x":2.25, "y":3}, {"x":3.25, "y":3}, {"x":4.25, "y":3}, {"x":5.25, "y":3}, {"x":6.25, "y":3}, {"x":7.25, "y":3}, {"x":8.25, "y":3}, {"x":9.25, "y":3}, {"x":10.25, "y":3}, {"x":11.25, "y":3}, {"x":12.25, "y":3, "w":2.75}, {"x":0, "y":4, "w":1.25}, {"x":1.25, "y":4, "w":1.25}, {"x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.25}, {"x":10, "y":4, "w":1.25}, {"x":11.25, "y":4, "w":1.25}, {"x":12.5, "y":4, "w":1.25}, {"x":13.75, "y":4, "w":1.25}]
+        },
+
+        "LAYOUT_60_hhkb": {
+            "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":0, "y":1, "w":1.5}, {"x":1.5, "y":1}, {"x":2.5, "y":1}, {"x":3.5, "y":1}, {"x":4.5, "y":1}, {"x":5.5, "y":1}, {"x":6.5, "y":1}, {"x":7.5, "y":1}, {"x":8.5, "y":1}, {"x":9.5, "y":1}, {"x":10.5, "y":1}, {"x":11.5, "y":1}, {"x":12.5, "y":1}, {"x":13.5, "y":1, "w":1.5}, {"x":0, "y":2, "w":1.75}, {"x":1.75, "y":2}, {"x":2.75, "y":2}, {"x":3.75, "y":2}, {"x":4.75, "y":2}, {"x":5.75, "y":2}, {"x":6.75, "y":2}, {"x":7.75, "y":2}, {"x":8.75, "y":2}, {"x":9.75, "y":2}, {"x":10.75, "y":2}, {"x":11.75, "y":2}, {"x":12.75, "y":2, "w":2.25}, {"x":0, "y":3, "w":2.25}, {"x":2.25, "y":3}, {"x":3.25, "y":3}, {"x":4.25, "y":3}, {"x":5.25, "y":3}, {"x":6.25, "y":3}, {"x":7.25, "y":3}, {"x":8.25, "y":3}, {"x":9.25, "y":3}, {"x":10.25, "y":3}, {"x":11.25, "y":3}, {"x":12.25, "y":3, "w":1.75}, {"x":14, "y":3}, {"x":1.5, "y":4}, {"x":2.5, "y":4, "w":1.5}, {"x":4, "y":4, "w":7}, {"x":11, "y":4, "w":1.5}, {"x":12.5, "y":4}]
+        }
+    }
+}

keyboards/foxlab/leaf60/universal/keymaps/default/config.h

@@ -0,0 +1,19 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here

keyboards/foxlab/leaf60/universal/keymaps/default/keymap.c

@@ -0,0 +1,46 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+	LAYOUT_all(
+		KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_GRV, KC_BSPC,
+		KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, 
+		KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, 
+		KC_LSFT, KC_NO, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_DEL, 
+		KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_SPC, KC_SPC, KC_RALT, MO(1), KC_RGUI, KC_RCTL),
+
+	LAYOUT_all(
+		RESET, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, KC_TRNS, 
+		KC_TRNS, BL_TOGG, BL_DEC, BL_INC, BL_STEP, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, 
+		KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS)
+
+};
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/foxlab/leaf60/universal/keymaps/default/readme.md

@@ -0,0 +1 @@
+# The default keymap for Universal Leaf60

keyboards/foxlab/leaf60/universal/readme.md

@@ -0,0 +1,13 @@
+# Fox Lab Leaf60
+
+A 60% gasket sandwich made by Fox Lab.
+
+Keyboard Maintainer: [Fox Lab](https://github.com/fox-lab), [MechMerlin](https://github.com/mechmerlin)  
+Hardware Supported: Leaf60 powered by the ATmega32U4  
+Hardware Availability: [Geekhack Group Buy](https://geekhack.org/index.php?topic=99002.0)  
+
+Make example for this keyboard (after setting up your build environment):
+
+    make foxlab/leaf60/universal:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/foxlab/leaf60/universal/rules.mk

@@ -0,0 +1,82 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   atmega32a    bootloadHID
+BOOTLOADER = atmel-dfu
+
+
+# If you don't know the bootloader type, then you can specify the
+# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
+#   Teensy halfKay      512
+#   Teensy++ halfKay    1024
+#   Atmel DFU loader    4096
+#   LUFA bootloader     4096
+#   USBaspLoader        2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = lite      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no        # Console for debug(+400)
+COMMAND_ENABLE = no        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = yes       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = yes        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
+
+LAYOUTS = 60_ansi 60_hhkb

keyboards/foxlab/leaf60/universal/universal.c

@@ -0,0 +1,61 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "universal.h"
+
+// Optional override functions below.
+// You can leave any or all of these undefined.
+// These are only required if you want to perform custom actions.
+
+void matrix_init_kb(void) {
+  // put your keyboard start-up code here
+  // runs once when the firmware starts up
+  setPinOutput(E6);
+  matrix_init_user();
+}
+
+/*
+
+void matrix_scan_kb(void) {
+  // put your looping keyboard code here
+  // runs every cycle (a lot)
+
+  matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+  // put your per-action keyboard code here
+  // runs for every action, just before processing by the firmware
+
+  return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+  // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+  led_set_user(usb_led);
+}
+
+*/
+
+
+void led_set_kb(uint8_t usb_led) {
+  if (IS_LED_ON(usb_led, USB_LED_CAPS_LOCK)) {
+    writePinLow(E6);
+  } else {
+    writePinHigh(E6);
+  }
+	led_set_user(usb_led);
+}

keyboards/foxlab/leaf60/universal/universal.h

@@ -0,0 +1,68 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+#define LAYOUT_all( \
+	K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \
+	K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113,       \
+	K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211,       K213,       \
+	K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313,       \
+	K400, K401, K402,       K404,       K406,       K408,       K410, K411, K412, K413        \
+) { \
+	{ K000,  K001,  K002,  K003,  K004,  K005,  K006,  K007,  K008,  K009,  K010,  K011,  K012,  K013,  K014 },  \
+	{ K100,  K101,  K102,  K103,  K104,  K105,  K106,  K107,  K108,  K109,  K110,  K111,  K112,  K113,  KC_NO }, \
+	{ K200,  K201,  K202,  K203,  K204,  K205,  K206,  K207,  K208,  K209,  K210,  K211,  KC_NO, K213,  KC_NO }, \
+	{ K300,  K301,  K302,  K303,  K304,  K305,  K306,  K307,  K308,  K309,  K310,  K311,  K312,  K313,  KC_NO }, \
+	{ K400,  K401,  K402,  KC_NO, K404,  KC_NO, K406,  KC_NO, K408,  KC_NO, K410,  K411,  K412,  K413,  KC_NO }  \
+}
+
+#define LAYOUT_60_ansi( \
+	K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K014, \
+	K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, \
+	K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211,       K213, \
+	K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312,             \
+	K400, K401, K402,             K406,                   K410, K411, K412, K413        \
+) { \
+	{ K000,  K001,  K002,  K003,  K004,  K005,  K006,  K007,  K008,  K009,  K010,  K011,  K012,  KC_NO, K014 },  \
+	{ K100,  K101,  K102,  K103,  K104,  K105,  K106,  K107,  K108,  K109,  K110,  K111,  K112,  K113,  KC_NO }, \
+	{ K200,  K201,  K202,  K203,  K204,  K205,  K206,  K207,  K208,  K209,  K210,  K211,  KC_NO, K213,  KC_NO }, \
+	{ K300,  KC_NO, K302,  K303,  K304,  K305,  K306,  K307,  K308,  K309,  K310,  K311,  K312,  KC_NO, KC_NO }, \
+	{ K400,  K401,  K402,  KC_NO, KC_NO, KC_NO, K406,  KC_NO, KC_NO, KC_NO, K410,  K411,  K412,  K413,  KC_NO }  \
+}
+
+#define LAYOUT_60_hhkb( \
+	K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \
+	K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113,       \
+	K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211,       K213,       \
+	K300,       K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313,       \
+	K401, K402,                         K406,                   K410, K411                    \
+) { \
+	{ K000,  K001,  K002,  K003,  K004,  K005,  K006,  K007,  K008,  K009,  K010,  K011,  K012,  K013,  K014 },  \
+	{ K100,  K101,  K102,  K103,  K104,  K105,  K106,  K107,  K108,  K109,  K110,  K111,  K112,  K113,  KC_NO }, \
+	{ K200,  K201,  K202,  K203,  K204,  K205,  K206,  K207,  K208,  K209,  K210,  K211,  KC_NO, K213,  KC_NO }, \
+	{ K300,  KC_NO, K302,  K303,  K304,  K305,  K306,  K307,  K308,  K309,  K310,  K311,  K312,  K313,  KC_NO }, \
+	{ KC_NO, K401,  K402,  KC_NO, KC_NO, KC_NO, K406,  KC_NO, KC_NO, KC_NO, K410,  K411,  KC_NO, KC_NO, KC_NO }  \
+}

keyboards/ft/mars80/config.h

@@ -0,0 +1,50 @@
+/*
+Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+#define VENDOR_ID       0x20A0
+#define PRODUCT_ID      0x422D
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    FT
+#define PRODUCT         Mars 8.0
+#define DESCRIPTION     A custom TKL Keyboard
+
+#define RGBLED_NUM 20
+
+#define MATRIX_ROWS 7
+#define MATRIX_COLS 14
+//                        0   1   2   3   4   5   6   7   8   9   A   B   C   D
+#define MATRIX_ROW_PINS { B0, B1, B2, B3, B5, B6, B7 }
+#define MATRIX_COL_PINS { A0, A1, A2, A3, A4, A5, A6, A7, C7, C6, C5, C4, C3, C2 }
+#define UNUSED_PINS     {}
+
+#define DIODE_DIRECTION COL2ROW
+#define DEBOUNCING_DELAY 5
+
+#define NO_BACKLIGHT_CLOCK
+#define BACKLIGHT_LEVELS 1
+#define RGBLIGHT_ANIMATIONS
+
+#define NO_UART 1
+
+/* key combination for magic key command */
+/* defined by default; to change, uncomment and set to the combination you want */
+// #define IS_COMMAND() (get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
+

keyboards/ft/mars80/info.json

@@ -0,0 +1,16 @@
+{
+    "keyboard_name": "Mars 8.0", 
+    "url": "", 
+    "maintainer": "qmk", 
+    "width": 18.25, 
+    "height": 6.5, 
+    "layouts": {
+        "LAYOUT_tkl_ansi": {
+            "layout": [{"x":0, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6.5, "y":0}, {"x":7.5, "y":0}, {"x":8.5, "y":0}, {"x":9.5, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":15.25, "y":0}, {"x":16.25, "y":0}, {"x":17.25, "y":0}, {"x":0, "y":1.5}, {"x":1, "y":1.5}, {"x":2, "y":1.5}, {"x":3, "y":1.5}, {"x":4, "y":1.5}, {"x":5, "y":1.5}, {"x":6, "y":1.5}, {"x":7, "y":1.5}, {"x":8, "y":1.5}, {"x":9, "y":1.5}, {"x":10, "y":1.5}, {"x":11, "y":1.5}, {"x":12, "y":1.5}, {"x":13, "y":1.5, "w":2}, {"x":15.25, "y":1.5}, {"x":16.25, "y":1.5}, {"x":17.25, "y":1.5}, {"x":0, "y":2.5, "w":1.5}, {"x":1.5, "y":2.5}, {"x":2.5, "y":2.5}, {"x":3.5, "y":2.5}, {"x":4.5, "y":2.5}, {"x":5.5, "y":2.5}, {"x":6.5, "y":2.5}, {"x":7.5, "y":2.5}, {"x":8.5, "y":2.5}, {"x":9.5, "y":2.5}, {"x":10.5, "y":2.5}, {"x":11.5, "y":2.5}, {"x":12.5, "y":2.5}, {"x":13.5, "y":2.5, "w":1.5}, {"x":15.25, "y":2.5}, {"x":16.25, "y":2.5}, {"x":17.25, "y":2.5}, {"x":0, "y":3.5, "w":1.75}, {"x":1.75, "y":3.5}, {"x":2.75, "y":3.5}, {"x":3.75, "y":3.5}, {"x":4.75, "y":3.5}, {"x":5.75, "y":3.5}, {"x":6.75, "y":3.5}, {"x":7.75, "y":3.5}, {"x":8.75, "y":3.5}, {"x":9.75, "y":3.5}, {"x":10.75, "y":3.5}, {"x":11.75, "y":3.5}, {"x":12.75, "y":3.5, "w":2.25}, {"x":0, "y":4.5, "w":2.25}, {"x":2.25, "y":4.5}, {"x":3.25, "y":4.5}, {"x":4.25, "y":4.5}, {"x":5.25, "y":4.5}, {"x":6.25, "y":4.5}, {"x":7.25, "y":4.5}, {"x":8.25, "y":4.5}, {"x":9.25, "y":4.5}, {"x":10.25, "y":4.5}, {"x":11.25, "y":4.5}, {"x":12.25, "y":4.5, "w":2.75}, {"x":16.25, "y":4.5}, {"x":0, "y":5.5, "w":1.25}, {"x":1.25, "y":5.5, "w":1.25}, {"x":2.5, "y":5.5, "w":1.25}, {"x":3.75, "y":5.5, "w":6.25}, {"x":10, "y":5.5, "w":1.25}, {"x":11.25, "y":5.5, "w":1.25}, {"x":12.5, "y":5.5, "w":1.25}, {"x":13.75, "y":5.5, "w":1.25}, {"x":15.25, "y":5.5}, {"x":16.25, "y":5.5}, {"x":17.25, "y":5.5}]
+        },
+
+        "LAYOUT_tkl_iso": {
+            "layout": [{"x":0, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6.5, "y":0}, {"x":7.5, "y":0}, {"x":8.5, "y":0}, {"x":9.5, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":15.25, "y":0}, {"x":16.25, "y":0}, {"x":17.25, "y":0}, {"x":0, "y":1.5}, {"x":1, "y":1.5}, {"x":2, "y":1.5}, {"x":3, "y":1.5}, {"x":4, "y":1.5}, {"x":5, "y":1.5}, {"x":6, "y":1.5}, {"x":7, "y":1.5}, {"x":8, "y":1.5}, {"x":9, "y":1.5}, {"x":10, "y":1.5}, {"x":11, "y":1.5}, {"x":12, "y":1.5}, {"x":13, "y":1.5, "w":2}, {"x":15.25, "y":1.5}, {"x":16.25, "y":1.5}, {"x":17.25, "y":1.5}, {"x":0, "y":2.5, "w":1.5}, {"x":1.5, "y":2.5}, {"x":2.5, "y":2.5}, {"x":3.5, "y":2.5}, {"x":4.5, "y":2.5}, {"x":5.5, "y":2.5}, {"x":6.5, "y":2.5}, {"x":7.5, "y":2.5}, {"x":8.5, "y":2.5}, {"x":9.5, "y":2.5}, {"x":10.5, "y":2.5}, {"x":11.5, "y":2.5}, {"x":12.5, "y":2.5}, {"x":13.75, "y":2.5, "w":1.25, "h":2}, {"x":15.25, "y":2.5}, {"x":16.25, "y":2.5}, {"x":17.25, "y":2.5}, {"x":0, "y":3.5, "w":1.75}, {"x":1.75, "y":3.5}, {"x":2.75, "y":3.5}, {"x":3.75, "y":3.5}, {"x":4.75, "y":3.5}, {"x":5.75, "y":3.5}, {"x":6.75, "y":3.5}, {"x":7.75, "y":3.5}, {"x":8.75, "y":3.5}, {"x":9.75, "y":3.5}, {"x":10.75, "y":3.5}, {"x":11.75, "y":3.5}, {"x":12.75, "y":3.5}, {"x":0, "y":4.5, "w":1.25}, {"x":1.25, "y":4.5}, {"x":2.25, "y":4.5}, {"x":3.25, "y":4.5}, {"x":4.25, "y":4.5}, {"x":5.25, "y":4.5}, {"x":6.25, "y":4.5}, {"x":7.25, "y":4.5}, {"x":8.25, "y":4.5}, {"x":9.25, "y":4.5}, {"x":10.25, "y":4.5}, {"x":11.25, "y":4.5}, {"x":12.25, "y":4.5, "w":2.75}, {"x":16.25, "y":4.5}, {"x":0, "y":5.5, "w":1.25}, {"x":1.25, "y":5.5, "w":1.25}, {"x":2.5, "y":5.5, "w":1.25}, {"x":3.75, "y":5.5, "w":6.25}, {"x":10, "y":5.5, "w":1.25}, {"x":11.25, "y":5.5, "w":1.25}, {"x":12.5, "y":5.5, "w":1.25}, {"x":13.75, "y":5.5, "w":1.25}, {"x":15.25, "y":5.5}, {"x":16.25, "y":5.5}, {"x":17.25, "y":5.5}]
+        }
+    }
+}

keyboards/ft/mars80/keymaps/default/config.h

@@ -0,0 +1,19 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here

keyboards/ft/mars80/keymaps/default/keymap.c

@@ -0,0 +1,75 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+// Defines the keycodes used by our macros in process_record_user
+enum custom_keycodes {
+  QMKBEST = SAFE_RANGE,
+  QMKURL
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+    [0] = LAYOUT_tkl_ansi(
+        KC_ESC,           KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,       KC_PSCR, KC_SLCK, KC_BRK,  \
+        KC_GRV,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC,      KC_INS,  KC_HOME, KC_PGUP, \
+        KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS,      KC_DEL,  KC_END,  KC_PGDN, \
+        KC_CAPS, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT,          KC_ENT,                                  \
+        KC_LSFT,          KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH,          KC_RSFT,               KC_UP,            \
+        KC_LCTL, KC_LGUI, KC_LALT,                            KC_SPC,                             KC_RALT, KC_RGUI, MO(1), KC_RCTL,      KC_LEFT, KC_DOWN, KC_RGHT  \
+    ),
+    [1] = LAYOUT_tkl_ansi(
+        _______,          _______, _______, _______, _______, _______, _______, _______, _______, KC_MSTP, KC_MPLY, KC_MPRV, KC_MNXT,      KC_MUTE, KC_VOLD, KC_VOLU, \
+        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,      _______, _______, _______, \
+        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,      _______, _______, _______, \
+        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,          KC_MSEL,                                 \
+        _______,          _______, _______, KC_CALC, _______, _______, _______, _______, _______, _______, _______,          _______,               _______,          \
+        _______, _______, _______,                            _______,                            _______, _______, _______, _______,      _______, _______, _______  \
+    ),
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  switch (keycode) {
+    case QMKBEST:
+      if (record->event.pressed) {
+        // when keycode QMKBEST is pressed
+        SEND_STRING("QMK is the best thing ever!");
+      } else {
+        // when keycode QMKBEST is released
+      }
+      break;
+    case QMKURL:
+      if (record->event.pressed) {
+        // when keycode QMKURL is pressed
+        SEND_STRING("https://qmk.fm/" SS_TAP(X_ENTER));
+      } else {
+        // when keycode QMKURL is released
+      }
+      break;
+  }
+  return true;
+}
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/ft/mars80/keymaps/default/readme.md

@@ -0,0 +1 @@
+# The default keymap for Mars 8.0

keyboards/ft/mars80/mars80.c

@@ -0,0 +1,91 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include "mars80.h"
+
+#include "rgblight.h"
+#include "i2c_master.h"
+#include "quantum.h"
+
+#ifdef RGBLIGHT_ENABLE
+extern rgblight_config_t rgblight_config;
+
+void rgblight_set(void) {
+    if (!rgblight_config.enable) {
+        for (uint8_t i = 0; i < RGBLED_NUM; i++) {
+            led[i].r = 0;
+            led[i].g = 0;
+            led[i].b = 0;
+        }
+    }
+
+    i2c_init();
+    i2c_transmit(0xb0, (uint8_t*)led, 3 * RGBLED_NUM, 100);
+}
+#endif
+
+void matrix_init_kb(void) {
+#ifdef RGBLIGHT_ENABLE
+    if (rgblight_config.enable) {
+        i2c_init();
+        i2c_transmit(0xb0, (uint8_t*)led, 3 * RGBLED_NUM, 100);
+    }
+#endif
+    // call user level keymaps, if any
+    matrix_init_user();
+}
+
+void matrix_scan_kb(void) {
+#ifdef RGBLIGHT_ENABLE
+    rgblight_task();
+#endif
+    matrix_scan_user();
+    /* Nothing else for now. */
+}
+
+__attribute__ ((weak))
+void matrix_scan_user(void) {
+}
+
+void backlight_init_ports(void) {
+    // initialize pins D0, D1, D4 and D6 as output
+    setPinOutput(D0);
+    setPinOutput(D1);
+    setPinOutput(D4);
+    setPinOutput(D6);
+
+    // turn backlight LEDs on
+    writePinHigh(D0);
+    writePinHigh(D1);
+    writePinHigh(D4);
+    writePinHigh(D6);
+}
+
+void backlight_set(uint8_t level) {
+	if (level == 0) {
+        // turn backlight LEDs off
+        writePinLow(D0);
+        writePinLow(D1);
+        writePinLow(D4);
+        writePinLow(D6);
+	} else {
+        // turn backlight LEDs on
+        writePinHigh(D0);
+        writePinHigh(D1);
+        writePinHigh(D4);
+        writePinHigh(D6);
+	}
+}

keyboards/ft/mars80/mars80.h

@@ -0,0 +1,63 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+
+#define LAYOUT_tkl_iso( \
+    k11, k13, k14, k15, k16, k18, k19, k1A, k1B, k1C, k10, k1D, k12, k02, k03, k00,      \
+    k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k2B, k2C, k20, k2D, k07, k06, k05, \
+    k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k3B, k3C, k30, k0D, k09, k08,      \
+    k41, k42, k43, k44, k45, k46, k47, k48, k49, k4A, k4B, k4C, k3D, k40,                \
+    k51, k4D, k52, k53, k54, k55, k56, k57, k58, k59, k5A, k5B, k5C, k5D,                \
+    k61, k62, k63, k65, k69, k6A, k6B, k6C, k60, k6D, k68                                \
+) \
+{ \
+   { k00,   KC_NO, k02, k03, KC_NO, k05, k06,   k07,   k08, k09, KC_NO, KC_NO, KC_NO, k0D   }, \
+   { k10,   k11,   k12, k13, k14,   k15, k16,   KC_NO, k18, k19, k1A,   k1B,   k1C,   k1D   }, \
+   { k20,   k21,   k22, k23, k24,   k25, k26,   k27,   k28, k29, k2A,   k2B,   KC_NO, k2D   }, \
+   { k30,   k31,   k32, k33, k34,   k35, k36,   k37,   k38, k39, k3A,   k3B,   k3C,   k3D   }, \
+   { k40,   k41,   k42, k43, k44,   k45, k46,   k47,   k48, k49, k4A,   k4B,   k4C,   k4D   }, \
+   { KC_NO, k51,   k52, k53, k54,   k55, k56,   k57,   k58, k59, k5A,   k5B,   k5C,   k5D   }, \
+   { k60,   k61,   k62, k63, KC_NO, k65, KC_NO, KC_NO, k68, k69, k6A,   k6B,   k6C,   k6D   }, \
+}
+
+#define LAYOUT_tkl_ansi( \
+    k11, k13, k14, k15, k16, k18, k19, k1A, k1B, k1C, k10, k1D, k12, k02, k03, k00,      \
+    k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k2B, k2C, k20, k2D, k07, k06, k05, \
+    k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k3B, k3C, k30, k3D, k0D, k09, k08, \
+    k41, k42, k43, k44, k45, k46, k47, k48, k49, k4A, k4B, k4C, k40,                     \
+    k51, k52, k53, k54, k55, k56, k57, k58, k59, k5A, k5B, k5C, k5D,                     \
+    k61, k62, k63, k65, k69, k6A, k6B, k6C, k60, k6D, k68                                \
+) \
+{ \
+   { k00,   KC_NO, k02, k03, KC_NO, k05, k06,   k07,   k08, k09, KC_NO, KC_NO, KC_NO, k0D   }, \
+   { k10,   k11,   k12, k13, k14,   k15, k16,   KC_NO, k18, k19, k1A,   k1B,   k1C,   k1D   }, \
+   { k20,   k21,   k22, k23, k24,   k25, k26,   k27,   k28, k29, k2A,   k2B,   KC_NO, k2D   }, \
+   { k30,   k31,   k32, k33, k34,   k35, k36,   k37,   k38, k39, k3A,   k3B,   k3C,   k3D   }, \
+   { k40,   k41,   k42, k43, k44,   k45, k46,   k47,   k48, k49, k4A,   k4B,   k4C,   KC_NO }, \
+   { KC_NO, k51,   k52, k53, k54,   k55, k56,   k57,   k58, k59, k5A,   k5B,   k5C,   k5D   }, \
+   { k60,   k61,   k62, k63, KC_NO, k65, KC_NO, KC_NO, k68, k69, k6A,   k6B,   k6C,   k6D   }, \
+}

keyboards/ft/mars80/readme.md

@@ -0,0 +1,44 @@
+# Mars 8.0
+
+TKL Keyboard with in switch backlight and RGB Underglow. 
+
+Keyboard Maintainer: [MechMerlin](https://github.com/mechmerlin)  
+Hardware Supported: Mars 8.0 PCB  
+Hardware Availability: [Geekhack Group Buy](https://geekhack.org/index.php?topic=93723.0)  
+
+Make example for this keyboard (after setting up your build environment):
+
+    make ft/mars80:default
+
+Flashing
+
+ps2avr(GB) boards use an atmega32a microcontroller and a different bootloader. It is not flashable using the regular QMK methods. 
+
+**Reset Key:** Hold down the key located at `K00`, commonly programmed as `Pause/Break` while plugging in the keyboard.
+
+Windows: 
+1. Download [HIDBootFlash](http://vusb.wikidot.com/project:hidbootflash).
+2. Place your keyboard into reset. 
+3. Press the `Find Device` button and ensure that your keyboard is found.
+4. Press the `Open .hex File` button and locate the `.hex` file you created.
+5. Press the `Flash Device` button and wait for the process to complete. 
+
+macOS:
+1. Install homebrew by typing the following:   
+    ```
+    /usr/bin/ruby -e "$(curl -fsSL https://raw.githubusercontent.com/Homebrew/install/master/install)"
+    ```
+2. Install `crosspack-avr`.  
+    ```
+    brew cask install crosspack-avr
+    ```
+3. Install the following packages:
+    ```
+    brew install python3
+    pip3 install pyusb
+    brew install --HEAD https://raw.githubusercontent.com/robertgzr/homebrew-tap/master/bootloadhid.rb
+    ```
+4. Place your keyboard into reset. 
+5. Flash the board by typing `bootloadHID -r` followed by the path to your `.hex` file. 
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/ft/mars80/rules.mk

@@ -0,0 +1,50 @@
+# Copyright 2019 Luiz Ribeiro <luizribeiro@gmail.com>
+#
+# This program is free software: you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation, either version 2 of the License, or
+# (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+# MCU name
+MCU = atmega32a
+PROTOCOL = VUSB
+
+# unsupported features for now
+NO_UART = yes
+NO_SUSPEND_POWER_DOWN = yes
+
+# processor frequency
+F_CPU = 12000000
+
+# Bootloader
+#     This definition is optional, and if your keyboard supports multiple bootloaders of
+#     different sizes, comment this out, and the correct address will be loaded
+#     automatically (+60). See bootloader.mk for all options.
+BOOTLOADER = bootloadHID
+
+# build options
+BOOTMAGIC_ENABLE = no
+MOUSEKEY_ENABLE = no
+EXTRAKEY_ENABLE = yes
+CONSOLE_ENABLE = yes
+COMMAND_ENABLE = yes
+BACKLIGHT_ENABLE = yes
+RGBLIGHT_ENABLE = yes
+RGBLIGHT_CUSTOM_DRIVER = yes
+
+OPT_DEFS = -DDEBUG_LEVEL=0
+
+SRC += i2c_master.c
+
+# programming options
+PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex
+
+LAYOUTS = tkl_ansi tkl_iso

keyboards/ft/mars80/usbconfig.h

@@ -0,0 +1,393 @@
+/* Name: usbconfig.h
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
+ * Author: Christian Starkjohann
+ * Creation Date: 2005-04-01
+ * Tabsize: 4
+ * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
+ * This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
+ */
+
+#pragma once
+
+#include "config.h"
+
+/*
+General Description:
+This file is an example configuration (with inline documentation) for the USB
+driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
+also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
+wire the lines to any other port, as long as D+ is also wired to INT0 (or any
+other hardware interrupt, as long as it is the highest level interrupt, see
+section at the end of this file).
+*/
+
+/* ---------------------------- Hardware Config ---------------------------- */
+
+#define USB_CFG_IOPORTNAME      D
+/* This is the port where the USB bus is connected. When you configure it to
+ * "B", the registers PORTB, PINB and DDRB will be used.
+ */
+#define USB_CFG_DMINUS_BIT      3
+/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
+ * This may be any bit in the port.
+ */
+#define USB_CFG_DPLUS_BIT       2
+/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
+ * This may be any bit in the port. Please note that D+ must also be connected
+ * to interrupt pin INT0! [You can also use other interrupts, see section
+ * "Optional MCU Description" below, or you can connect D- to the interrupt, as
+ * it is required if you use the USB_COUNT_SOF feature. If you use D- for the
+ * interrupt, the USB interrupt will also be triggered at Start-Of-Frame
+ * markers every millisecond.]
+ */
+#define USB_CFG_CLOCK_KHZ       (F_CPU/1000)
+/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
+ * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
+ * require no crystal, they tolerate +/- 1% deviation from the nominal
+ * frequency. All other rates require a precision of 2000 ppm and thus a
+ * crystal!
+ * Since F_CPU should be defined to your actual clock rate anyway, you should
+ * not need to modify this setting.
+ */
+#define USB_CFG_CHECK_CRC       0
+/* Define this to 1 if you want that the driver checks integrity of incoming
+ * data packets (CRC checks). CRC checks cost quite a bit of code size and are
+ * currently only available for 18 MHz crystal clock. You must choose
+ * USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
+ */
+
+/* ----------------------- Optional Hardware Config ------------------------ */
+
+/* #define USB_CFG_PULLUP_IOPORTNAME   D */
+/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
+ * V+, you can connect and disconnect the device from firmware by calling
+ * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
+ * This constant defines the port on which the pullup resistor is connected.
+ */
+/* #define USB_CFG_PULLUP_BIT          4 */
+/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
+ * above) where the 1.5k pullup resistor is connected. See description
+ * above for details.
+ */
+
+/* --------------------------- Functional Range ---------------------------- */
+
+#define USB_CFG_HAVE_INTRIN_ENDPOINT    1
+/* Define this to 1 if you want to compile a version with two endpoints: The
+ * default control endpoint 0 and an interrupt-in endpoint (any other endpoint
+ * number).
+ */
+#define USB_CFG_HAVE_INTRIN_ENDPOINT3   1
+/* Define this to 1 if you want to compile a version with three endpoints: The
+ * default control endpoint 0, an interrupt-in endpoint 3 (or the number
+ * configured below) and a catch-all default interrupt-in endpoint as above.
+ * You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
+ */
+#define USB_CFG_EP3_NUMBER              3
+/* If the so-called endpoint 3 is used, it can now be configured to any other
+ * endpoint number (except 0) with this macro. Default if undefined is 3.
+ */
+/* #define USB_INITIAL_DATATOKEN           USBPID_DATA1 */
+/* The above macro defines the startup condition for data toggling on the
+ * interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
+ * Since the token is toggled BEFORE sending any data, the first packet is
+ * sent with the oposite value of this configuration!
+ */
+#define USB_CFG_IMPLEMENT_HALT          0
+/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
+ * for endpoint 1 (interrupt endpoint). Although you may not need this feature,
+ * it is required by the standard. We have made it a config option because it
+ * bloats the code considerably.
+ */
+#define USB_CFG_SUPPRESS_INTR_CODE      0
+/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
+ * want to send any data over them. If this macro is defined to 1, functions
+ * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
+ * you need the interrupt-in endpoints in order to comply to an interface
+ * (e.g. HID), but never want to send any data. This option saves a couple
+ * of bytes in flash memory and the transmit buffers in RAM.
+ */
+#define USB_CFG_INTR_POLL_INTERVAL      1
+/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
+ * interval. The value is in milliseconds and must not be less than 10 ms for
+ * low speed devices.
+ */
+#define USB_CFG_IS_SELF_POWERED         0
+/* Define this to 1 if the device has its own power supply. Set it to 0 if the
+ * device is powered from the USB bus.
+ */
+#define USB_CFG_MAX_BUS_POWER           500
+/* Set this variable to the maximum USB bus power consumption of your device.
+ * The value is in milliamperes. [It will be divided by two since USB
+ * communicates power requirements in units of 2 mA.]
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITE      1
+/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
+ * transfers. Set it to 0 if you don't need it and want to save a couple of
+ * bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_READ       0
+/* Set this to 1 if you need to send control replies which are generated
+ * "on the fly" when usbFunctionRead() is called. If you only want to send
+ * data from a static buffer, set it to 0 and return the data from
+ * usbFunctionSetup(). This saves a couple of bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITEOUT   0
+/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
+ * You must implement the function usbFunctionWriteOut() which receives all
+ * interrupt/bulk data sent to any endpoint other than 0. The endpoint number
+ * can be found in 'usbRxToken'.
+ */
+#define USB_CFG_HAVE_FLOWCONTROL        0
+/* Define this to 1 if you want flowcontrol over USB data. See the definition
+ * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
+ * usbdrv.h.
+ */
+#define USB_CFG_DRIVER_FLASH_PAGE       0
+/* If the device has more than 64 kBytes of flash, define this to the 64 k page
+ * where the driver's constants (descriptors) are located. Or in other words:
+ * Define this to 1 for boot loaders on the ATMega128.
+ */
+#define USB_CFG_LONG_TRANSFERS          0
+/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
+ * in a single control-in or control-out transfer. Note that the capability
+ * for long transfers increases the driver size.
+ */
+/* #define USB_RX_USER_HOOK(data, len)     if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
+/* This macro is a hook if you want to do unconventional things. If it is
+ * defined, it's inserted at the beginning of received message processing.
+ * If you eat the received message and don't want default processing to
+ * proceed, do a return after doing your things. One possible application
+ * (besides debugging) is to flash a status LED on each packet.
+ */
+/* #define USB_RESET_HOOK(resetStarts)     if(!resetStarts){hadUsbReset();} */
+/* This macro is a hook if you need to know when an USB RESET occurs. It has
+ * one parameter which distinguishes between the start of RESET state and its
+ * end.
+ */
+/* #define USB_SET_ADDRESS_HOOK()              hadAddressAssigned(); */
+/* This macro (if defined) is executed when a USB SET_ADDRESS request was
+ * received.
+ */
+#define USB_COUNT_SOF                   1
+/* define this macro to 1 if you need the global variable "usbSofCount" which
+ * counts SOF packets. This feature requires that the hardware interrupt is
+ * connected to D- instead of D+.
+ */
+/* #ifdef __ASSEMBLER__
+ * macro myAssemblerMacro
+ *     in      YL, TCNT0
+ *     sts     timer0Snapshot, YL
+ *     endm
+ * #endif
+ * #define USB_SOF_HOOK                    myAssemblerMacro
+ * This macro (if defined) is executed in the assembler module when a
+ * Start Of Frame condition is detected. It is recommended to define it to
+ * the name of an assembler macro which is defined here as well so that more
+ * than one assembler instruction can be used. The macro may use the register
+ * YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
+ * immediately after an SOF pulse may be lost and must be retried by the host.
+ * What can you do with this hook? Since the SOF signal occurs exactly every
+ * 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
+ * designs running on the internal RC oscillator.
+ * Please note that Start Of Frame detection works only if D- is wired to the
+ * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
+ */
+#define USB_CFG_CHECK_DATA_TOGGLING     0
+/* define this macro to 1 if you want to filter out duplicate data packets
+ * sent by the host. Duplicates occur only as a consequence of communication
+ * errors, when the host does not receive an ACK. Please note that you need to
+ * implement the filtering yourself in usbFunctionWriteOut() and
+ * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
+ * for each control- and out-endpoint to check for duplicate packets.
+ */
+#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH   0
+/* define this macro to 1 if you want the function usbMeasureFrameLength()
+ * compiled in. This function can be used to calibrate the AVR's RC oscillator.
+ */
+#define USB_USE_FAST_CRC                0
+/* The assembler module has two implementations for the CRC algorithm. One is
+ * faster, the other is smaller. This CRC routine is only used for transmitted
+ * messages where timing is not critical. The faster routine needs 31 cycles
+ * per byte while the smaller one needs 61 to 69 cycles. The faster routine
+ * may be worth the 32 bytes bigger code size if you transmit lots of data and
+ * run the AVR close to its limit.
+ */
+
+/* -------------------------- Device Description --------------------------- */
+
+#define USB_CFG_VENDOR_ID       (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF)
+/* USB vendor ID for the device, low byte first. If you have registered your
+ * own Vendor ID, define it here. Otherwise you may use one of obdev's free
+ * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
+ * the implications!
+ */
+#define USB_CFG_DEVICE_ID       (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF)
+/* This is the ID of the product, low byte first. It is interpreted in the
+ * scope of the vendor ID. If you have registered your own VID with usb.org
+ * or if you have licensed a PID from somebody else, define it here. Otherwise
+ * you may use one of obdev's free shared VID/PID pairs. See the file
+ * USB-IDs-for-free.txt for details!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
+ * the implications!
+ */
+#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+/* Version number of the device: Minor number first, then major number.
+ */
+#define USB_CFG_VENDOR_NAME     'f', 't'
+#define USB_CFG_VENDOR_NAME_LEN 2
+/* These two values define the vendor name returned by the USB device. The name
+ * must be given as a list of characters under single quotes. The characters
+ * are interpreted as Unicode (UTF-16) entities.
+ * If you don't want a vendor name string, undefine these macros.
+ * ALWAYS define a vendor name containing your Internet domain name if you use
+ * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
+ * details.
+ */
+#define USB_CFG_DEVICE_NAME     'm', 'a', 'r', 's', '8', '0'
+#define USB_CFG_DEVICE_NAME_LEN 6
+/* Same as above for the device name. If you don't want a device name, undefine
+ * the macros. See the file USB-IDs-for-free.txt before you assign a name if
+ * you use a shared VID/PID.
+ */
+/*#define USB_CFG_SERIAL_NUMBER   'N', 'o', 'n', 'e' */
+/*#define USB_CFG_SERIAL_NUMBER_LEN   0 */
+/* Same as above for the serial number. If you don't want a serial number,
+ * undefine the macros.
+ * It may be useful to provide the serial number through other means than at
+ * compile time. See the section about descriptor properties below for how
+ * to fine tune control over USB descriptors such as the string descriptor
+ * for the serial number.
+ */
+#define USB_CFG_DEVICE_CLASS        0
+#define USB_CFG_DEVICE_SUBCLASS     0
+/* See USB specification if you want to conform to an existing device class.
+ * Class 0xff is "vendor specific".
+ */
+#define USB_CFG_INTERFACE_CLASS     3   /* HID */
+#define USB_CFG_INTERFACE_SUBCLASS  1   /* Boot */
+#define USB_CFG_INTERFACE_PROTOCOL  1   /* Keyboard */
+/* See USB specification if you want to conform to an existing device class or
+ * protocol. The following classes must be set at interface level:
+ * HID class is 3, no subclass and protocol required (but may be useful!)
+ * CDC class is 2, use subclass 2 and protocol 1 for ACM
+ */
+#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH    0
+/* Define this to the length of the HID report descriptor, if you implement
+ * an HID device. Otherwise don't define it or define it to 0.
+ * If you use this define, you must add a PROGMEM character array named
+ * "usbHidReportDescriptor" to your code which contains the report descriptor.
+ * Don't forget to keep the array and this define in sync!
+ */
+
+/* #define USB_PUBLIC static */
+/* Use the define above if you #include usbdrv.c instead of linking against it.
+ * This technique saves a couple of bytes in flash memory.
+ */
+
+/* ------------------- Fine Control over USB Descriptors ------------------- */
+/* If you don't want to use the driver's default USB descriptors, you can
+ * provide our own. These can be provided as (1) fixed length static data in
+ * flash memory, (2) fixed length static data in RAM or (3) dynamically at
+ * runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
+ * information about this function.
+ * Descriptor handling is configured through the descriptor's properties. If
+ * no properties are defined or if they are 0, the default descriptor is used.
+ * Possible properties are:
+ *   + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
+ *     at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
+ *     used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
+ *     you want RAM pointers.
+ *   + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
+ *     in static memory is in RAM, not in flash memory.
+ *   + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
+ *     the driver must know the descriptor's length. The descriptor itself is
+ *     found at the address of a well known identifier (see below).
+ * List of static descriptor names (must be declared PROGMEM if in flash):
+ *   char usbDescriptorDevice[];
+ *   char usbDescriptorConfiguration[];
+ *   char usbDescriptorHidReport[];
+ *   char usbDescriptorString0[];
+ *   int usbDescriptorStringVendor[];
+ *   int usbDescriptorStringDevice[];
+ *   int usbDescriptorStringSerialNumber[];
+ * Other descriptors can't be provided statically, they must be provided
+ * dynamically at runtime.
+ *
+ * Descriptor properties are or-ed or added together, e.g.:
+ * #define USB_CFG_DESCR_PROPS_DEVICE   (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
+ *
+ * The following descriptors are defined:
+ *   USB_CFG_DESCR_PROPS_DEVICE
+ *   USB_CFG_DESCR_PROPS_CONFIGURATION
+ *   USB_CFG_DESCR_PROPS_STRINGS
+ *   USB_CFG_DESCR_PROPS_STRING_0
+ *   USB_CFG_DESCR_PROPS_STRING_VENDOR
+ *   USB_CFG_DESCR_PROPS_STRING_PRODUCT
+ *   USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
+ *   USB_CFG_DESCR_PROPS_HID
+ *   USB_CFG_DESCR_PROPS_HID_REPORT
+ *   USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
+ *
+ * Note about string descriptors: String descriptors are not just strings, they
+ * are Unicode strings prefixed with a 2 byte header. Example:
+ * int  serialNumberDescriptor[] = {
+ *     USB_STRING_DESCRIPTOR_HEADER(6),
+ *     'S', 'e', 'r', 'i', 'a', 'l'
+ * };
+ */
+
+#define USB_CFG_DESCR_PROPS_DEVICE                  0
+#define USB_CFG_DESCR_PROPS_CONFIGURATION           USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_CONFIGURATION           0
+#define USB_CFG_DESCR_PROPS_STRINGS                 0
+#define USB_CFG_DESCR_PROPS_STRING_0                0
+#define USB_CFG_DESCR_PROPS_STRING_VENDOR           0
+#define USB_CFG_DESCR_PROPS_STRING_PRODUCT          0
+#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER    0
+#define USB_CFG_DESCR_PROPS_HID                     USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_HID                     0
+#define USB_CFG_DESCR_PROPS_HID_REPORT              USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_HID_REPORT              0
+#define USB_CFG_DESCR_PROPS_UNKNOWN                 0
+
+#define usbMsgPtr_t unsigned short
+/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
+ * a scalar type here because gcc generates slightly shorter code for scalar
+ * arithmetics than for pointer arithmetics. Remove this define for backward
+ * type compatibility or define it to an 8 bit type if you use data in RAM only
+ * and all RAM is below 256 bytes (tiny memory model in IAR CC).
+ */
+
+/* ----------------------- Optional MCU Description ------------------------ */
+
+/* The following configurations have working defaults in usbdrv.h. You
+ * usually don't need to set them explicitly. Only if you want to run
+ * the driver on a device which is not yet supported or with a compiler
+ * which is not fully supported (such as IAR C) or if you use a differnt
+ * interrupt than INT0, you may have to define some of these.
+ */
+/* #define USB_INTR_CFG            MCUCR */
+/* #define USB_INTR_CFG_SET        ((1 << ISC00) | (1 << ISC01)) */
+/* #define USB_INTR_CFG_CLR        0 */
+/* #define USB_INTR_ENABLE         GIMSK */
+/* #define USB_INTR_ENABLE_BIT     INT0 */
+/* #define USB_INTR_PENDING        GIFR */
+/* #define USB_INTR_PENDING_BIT    INTF0 */
+/* #define USB_INTR_VECTOR         INT0_vect */
+
+/* Set INT1 for D- falling edge to count SOF */
+/* #define USB_INTR_CFG            EICRA */
+#define USB_INTR_CFG_SET        ((1 << ISC11) | (0 << ISC10))
+/* #define USB_INTR_CFG_CLR        0 */
+/* #define USB_INTR_ENABLE         EIMSK */
+#define USB_INTR_ENABLE_BIT     INT1
+/* #define USB_INTR_PENDING        EIFR */
+#define USB_INTR_PENDING_BIT    INTF1
+#define USB_INTR_VECTOR         INT1_vect

keyboards/georgi/config.h

@@ -23,7 +23,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 /* Defaults */
 
-#define VERSION "v1.0: Stenoknight"
+#define VERSION "v1.1: ClayM"
 #define VERBOSE
 
 #define FORCE_NKRO

keyboards/georgi/keymaps/colemak-dh/keymap.c

@@ -0,0 +1,306 @@
+/*
+ * Good on you for modifying your layout, this is the most nonQMK layout you will come across
+ * There are three modes, Steno (the default), QWERTY (Toggleable) and a Momentary symbol layer
+ *
+ * Don't modify the steno layer directly, instead add chords using the keycodes and macros
+ * from sten.h to the layout you want to modify.
+ *
+ * Observe the comment above processQWERTY!
+ *
+ * http://docs.gboards.ca
+ */
+
+#include QMK_KEYBOARD_H
+#include "sten.h"
+#include "keymap_steno.h"
+#define IGNORE_MOD_TAP_INTERRUPT
+
+// Steno Layers
+#define FUNCT	( LSD | LK | LP | LH )
+#define MEDIA	( LSD | LK | LW | LR )
+#define MOVE	( LSD | LK )
+#define NUM		( PWR )
+#define SYM		( RZ )
+
+// Keys and chords that, once they appear, are added to every subsequent partial chord
+// until the whole thing is sent.
+uint32_t stenoLayers[] = {NUM, SYM, MOVE, MEDIA, FUNCT};
+
+// QMK Layers
+#define STENO_LAYER   0
+#define GAMING		  1
+#define GAMING_2	  2
+
+/* Keyboard Layout
+ * ,---------------------------------.	  ,------------------------------.
+ * | FN  | LSU | LFT | LP | LH | ST1 |	  | ST3 | RF | RP | RL | RT | RD |
+ * |-----+-----+-----+----+----|-----|	  |-----|----+----+----+----+----|
+ * | PWR | LSD | LK  | LW | LR | ST2 |	  | ST4 | RR | RB | RG | RS | RZ |
+ * `---------------------------------'	  `------------------------------'
+ *					 ,---------------,	  .---------------.
+ *					 | LNO | LA | LO |	  | RE | RU | RNO |
+ *					 `---------------'	  `---------------'
+ */
+
+// Note: You can only use basic keycodes here!
+//
+// P() is just a wrapper to make your life easier.
+// PC() applies the mapping to all of the StenoLayers. For overloading, define these last.
+//
+// FN is unavailable. That is reserved for system use.
+// Chords containing PWR are always available, even in steno mode.
+//
+// http://docs.gboards.ca
+uint32_t processQwerty(bool lookup) {
+	// Special keys
+	P( RT  | RS  | RD  | RZ | LNO,		SEND_STRING(VERSION); SEND_STRING(__DATE__));
+	P( LFT | LK  | LP  | LW,			REPEAT());
+
+	// Mouse Keys
+	/* P( LO  | LSD | LK,	CLICK_MOUSE(KC_MS_BTN2)); */
+	/* P( LO  | LR  | LW,	CLICK_MOUSE(KC_MS_BTN1)); */
+
+
+/* Function layer
+ * ,-----------------------------------,    ,-----------------------------------,
+ * |     |     |     | NCTFUNCTF |     |    |     | F1  | F2  | F3  | F4  |     |
+ * |     +     +     +     +     +     |    |     + F5  + F6  + F7  + F8  +     |
+ * |     | FUNCTFUNC |     |     |     |    |     | F9  | F10 | F11 | F12 |     |
+ * `-----+-----+-----+-----+-----+-----'    `-----+-----+-----+-----+-----+-----'
+*/
+	P( FUNCT | RF,			SEND(KC_F1));
+	P( FUNCT | RP,			SEND(KC_F2));
+	P( FUNCT | RL,			SEND(KC_F3));
+	P( FUNCT | RT,			SEND(KC_F4));
+
+	P( FUNCT | RF | RR,		SEND(KC_F5));
+	P( FUNCT | RP | RB,		SEND(KC_F6));
+	P( FUNCT | RL | RG,		SEND(KC_F7));
+	P( FUNCT | RT | RS,		SEND(KC_F8));
+
+	P( FUNCT | RR,			SEND(KC_F9));
+	P( FUNCT | RG,			SEND(KC_F10));
+	P( FUNCT | RB,			SEND(KC_F11));
+	P( FUNCT | RS,			SEND(KC_F12));
+
+
+/* Movement layer
+ * ,-----------------------------------,    ,-----------------------------------,
+ * |     |     |     |     |     |     |    |     | <-  |  ↓  |  ↑  | ->  |     |
+ * |     +     +     +     +     +     |    |     +     +     +     +     +     |
+ * |     | MOVEMOVEM |     |     |     |    |     | Hm  | PgD | PgU | End |     |
+ * `-----+-----+-----+-----+-----+-----'    `-----+-----+-----+-----+-----+-----'
+*/
+	P( MOVE | RF,			SEND(KC_LEFT));
+	P( MOVE | RP,			SEND(KC_DOWN));
+	P( MOVE | RL,			SEND(KC_UP));
+	P( MOVE | RT,			SEND(KC_RIGHT));
+
+	P( MOVE | RR,			SEND(KC_HOME));
+	P( MOVE | RB,			SEND(KC_PGDN));
+	P( MOVE | RG,			SEND(KC_PGUP));
+	P( MOVE | RS,			SEND(KC_END));
+
+
+/* Media Layer
+ * ,-----------------------------------,    ,-----------------------------------,
+ * |     |     |     |     |     |     |    |     |Prev |Play | PLY |Next | VolU|
+ * |     +     +     +     +     +     |    |     +     +     +     +     +     |
+ * |     | MEDIAMEDIAMEDIAMEDIAM |     |    |     |     |     |     |Mute | VolD|
+ * `-----+-----+-----+-----+-----+-----'    `-----+-----+-----+-----+-----+-----'
+*/
+	P( MEDIA | RF,			SEND(KC_MPRV));
+	P( MEDIA | RP,			SEND(KC_MPLY));
+	P( MEDIA | RL,			SEND(KC_MPLY));
+	P( MEDIA | RT,			SEND(KC_MNXT));
+	P( MEDIA | RD,			SEND(KC_VOLU));
+
+	P( MEDIA | RS,			SEND(KC_MUTE));
+	P( MEDIA | RZ,			SEND(KC_VOLD));
+
+
+/* Numbers
+ * ,-----------------------------------,    ,-----------------------------------,
+ * |     |     |  a  |  b  |  c  |     |    |  :  |  1  |  2  |  3  |  .  |     |
+ * |     +     +  d  +  e  +  f  +     |    |  0  +  4  +  5  +  6  +  -  +     |
+ * | NUM |     |     |     |     |     |    |     |  7  |  8  |  9  |  0  |     |
+ * `-----+-----+-----+-----+-----+-----'    `-----+-----+-----+-----+-----+-----'
+*/
+	P( NUM | LFT,			SEND(KC_A));
+	P( NUM | LP,			SEND(KC_B));
+	P( NUM | LH,			SEND(KC_C));
+	P( NUM | LK,			SEND(KC_D));
+	P( NUM | LW,			SEND(KC_E));
+	P( NUM | LR,			SEND(KC_F));
+
+	// Right hand
+	P( NUM | ST3,			SEND_STRING(":"));
+	P( NUM | RF,			SEND(KC_1));
+	P( NUM | RP,			SEND(KC_2));
+	P( NUM | RL,			SEND(KC_3));
+	P( NUM | RT,			SEND(KC_DOT));
+
+	P( NUM | ST3 | ST4,		SEND(KC_0));
+	P( NUM | RF  | RR,		SEND(KC_4));
+	P( NUM | RP  | RB,		SEND(KC_5));
+	P( NUM | RG  | RL,		SEND(KC_6));
+	P( NUM | RT  | RS,		SEND(KC_MINUS));
+
+	P( NUM | RR,			SEND(KC_7));
+	P( NUM | RB,			SEND(KC_8));
+	P( NUM | RG,			SEND(KC_9));
+	P( NUM | RS,			SEND(KC_0));
+
+
+/* Symbols
+ * ,-----------------------------------,    ,-----------------------------------,
+ * |     |  `  |  [  |  {  |  (  |  <  |    |  >  |  )  |  }  |  ]  |  ?  |     |
+ * |     +  ~  +  -  +  '  +  :  +  _  |    |  \  +  =  +  "  +  +  +  ?  +     |
+ * |     |  !  |  @  |  #  |  $  |  %  |    |  |  |  ^  |  &  |  *  |  ?  | SYM |
+ * `-----+-----+-----+-----+-----+-----'    `-----+-----+-----+-----+-----+-----'
+*/
+	// Left hand
+	P( SYM | LSU,			SEND(KC_GRV));
+	P( SYM | LFT,			SEND(KC_LBRC));
+	P( SYM | LP,			SEND_STRING("{"));
+	P( SYM | LH,			SEND_STRING("("));
+	P( SYM | ST1,			SEND_STRING("<"));
+
+	P( SYM | LSU | LSD,		SEND_STRING("~"));
+	P( SYM | LFT | LK,		SEND(KC_MINS));
+	P( SYM | LP  | LW,		SEND(KC_QUOTE));
+	P( SYM | LH  | LR,		SEND_STRING(":"));
+	P( SYM | ST1 | ST2,		SEND_STRING("_"));
+
+	P( SYM | LSD,			SEND_STRING("!"));
+	P( SYM | LK,			SEND_STRING("@"));
+	P( SYM | LW,			SEND_STRING("#"));
+	P( SYM | LR,			SEND_STRING("$"));
+	P( SYM | ST2,			SEND_STRING("%"));
+
+	// Right hand
+	P( SYM | ST3,			SEND_STRING(">"));
+	P( SYM | RF,			SEND_STRING(")"));
+	P( SYM | RP,			SEND_STRING("}"));
+	P( SYM | RL,			SEND_STRING("]"));
+	P( SYM | RT,			SEND_STRING("?"));
+
+	P( SYM | ST3 | ST4,		SEND(KC_BSLASH));
+	P( SYM | RF  | RR,		SEND(KC_EQUAL));
+	P( SYM | RP  | RB,		SEND_STRING("\""));
+	P( SYM | RG  | RL,		SEND_STRING("+"));
+	P( SYM | RT  | RS,		SEND_STRING("?"));
+
+	P( SYM | ST4,			SEND_STRING("|"));
+	P( SYM | RR,			SEND_STRING("^"));
+	P( SYM | RB,			SEND_STRING("&"));
+	P( SYM | RG,			SEND_STRING("*"));
+	P( SYM | RS,			SEND_STRING("?"));
+
+
+/* Letters
+ * ,-----------------------------------,    ,-----------------------------------,
+ * |     |  Q  |  W  |  F  |  P  |  B  |    |  J  |  L  |  U  |  Y  |  ;  | ctl |
+ * +-----+- A -+- R -+- S -+- T -+- G -|    |- M -+- N -+- E -+- I -+- O -+-----|
+ * | bsp |  Z  |  X  |  C  |  D  |  V  |    |  K  |  H  |  ,  |  .  |  /  | del |
+ * `-----+-----+-----+-----+-----+-----'    `-----+-----+-----+-----+-----+-----'
+ *					   ,---------------,    .---------------.
+ *					   | alt | ent|shfr|    | spc| gui| alt |
+ *					   `---------------'    `---------------'
+*/
+	// Left hand
+	P( LSU,					SEND(KC_Q));
+	P( LFT,					SEND(KC_W));
+	P( LP,					SEND(KC_F));
+	P( LH,					SEND(KC_P));
+	P( ST1,					SEND(KC_B));
+
+	P( LSU | LSD,			SEND(KC_A));
+	P( LFT | LK,			SEND(KC_R));
+	P( LP  | LW,			SEND(KC_S));
+	P( LH  | LR,			SEND(KC_T));
+	P( ST1 | ST2,			SEND(KC_G));
+
+	P( LSD,					SEND(KC_Z));
+	P( LK,					SEND(KC_X));
+	P( LW,					SEND(KC_C));
+	P( LR,					SEND(KC_D));
+	P( ST2,					SEND(KC_V));
+
+	// Right hand
+	P( ST3,					SEND(KC_J));
+	P( RF,					SEND(KC_L));
+	P( RP,					SEND(KC_U));
+	P( RL,					SEND(KC_Y));
+	P( RT,					SEND(KC_SCLN));
+
+	P( ST3 | ST4,			SEND(KC_M));
+	P( RF  | RR,			SEND(KC_N));
+	P( RP  | RB,			SEND(KC_E));
+	P( RG  | RL,			SEND(KC_I));
+	P( RT  | RS,			SEND(KC_O));
+
+	P( ST4,					SEND(KC_K));
+	P( RR,					SEND(KC_H));
+	P( RB,					SEND(KC_COMM));
+	P( RG,					SEND(KC_DOT));
+	P( RS,					SEND(KC_SLSH));
+
+	// Thumb Chords and modifiers
+	//
+	PC( LNO | RNO | LA | RU,		SEND(KC_LCTL); SEND(KC_LSFT));
+	PC( LNO | LA  | RE,				SEND(KC_LCTL); SEND(KC_LSFT); SEND(KC_LALT));
+
+	// overrides
+	P( PWR | LO,			SEND(KC_LSFT); SEND(KC_BSPC));
+	P( PWR | RD,			SEND(KC_LCTL); SEND(KC_BSPC));
+	P( RZ | RD,				SEND(KC_LCTL); SEND(KC_DEL));
+
+	PC( LNO | LA | LO,		SEND(KC_LSFT); SEND(KC_ESC));
+	PC( LA | LO,			SEND(KC_ESC));
+	PC( LNO,				SEND(KC_LALT));
+	PC( LA,					SEND(KC_ENT));
+	PC( LO,					SEND(KC_LSFT));
+
+	PC( RNO,				SEND(KC_RALT));
+	PC( RE | RU,			SEND(KC_TAB));
+	PC( RE,					SEND(KC_SPC));
+	PC( RU,					SEND(KC_LGUI));
+   
+	PC( PWR,				SEND(KC_BSPC));
+	PC( RD,					SEND(KC_LCTL));
+	P( RZ,					SEND(KC_DEL));
+
+	return 0;
+}
+
+// "Layers"
+// Steno layer should be first in your map.
+// When PWR | FN | ST3 | ST4 is pressed, the layer is increased to the next map. You must return to STENO_LAYER at the end.
+// If you need more space for chords, remove the two gaming layers.
+// Note: If using NO_ACTION_TAPPING, LT will not work!
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+	// Main layer, everything goes through here
+	[STENO_LAYER] = LAYOUT_georgi(
+			STN_FN,  STN_S1,  STN_TL,  STN_PL,	STN_HL,  STN_ST1,		STN_ST3, STN_FR,  STN_PR,  STN_LR,	STN_TR,  STN_DR,
+			STN_PWR, STN_S2,  STN_KL,  STN_WL,	STN_RL,  STN_ST2,		STN_ST4, STN_RR,  STN_BR,  STN_GR,	STN_SR,  STN_ZR,
+								   STN_N1,		STN_A,	 STN_O,			STN_E,	 STN_U,   STN_N7
+	),
+	// Gaming layer with Numpad, Very limited
+	[GAMING] = LAYOUT_georgi(
+		KC_LSFT, KC_Q,	  KC_W,    KC_E,	KC_R,	 KC_T,						 KC_Y,	  KC_U,    KC_I,	KC_O,	 KC_P,	  KC_ENT,
+		KC_LCTL, KC_A,	  KC_S,    KC_D,	KC_F,	 KC_G,						 KC_H,	  KC_J,    KC_K,	KC_L,	 KC_SCLN, KC_DQUO,
+								   KC_LALT, KC_SPC,  LT(GAMING_2, KC_ENT),		 KC_DEL,  KC_ASTR, TO(STENO_LAYER)
+	),
+
+	[GAMING_2] = LAYOUT_georgi(
+		KC_LSFT, KC_1,	  KC_2,    KC_3,	KC_4,	 KC_5,			KC_6,	 KC_7,	  KC_8,    KC_9,	KC_0,	 KC_MINS,
+		KC_LCTL, KC_Z,	  KC_X,    KC_C,	KC_V,	 KC_B,			KC_N,	 KC_M,	  KC_LT,   KC_GT,	KC_QUES, KC_RSFT,
+								   KC_LALT, KC_SPC,  KC_ENT,		KC_DEL,  KC_ASTR, TO(STENO_LAYER)
+	)
+};
+
+// Don't fuck with this, thanks.
+size_t keymapsCount  = sizeof(keymaps)/sizeof(keymaps[0]);
+size_t stenoLayerCount = sizeof(stenoLayers)/sizeof(stenoLayers[0]);

keyboards/georgi/keymaps/colemak-dh/readme.md

@@ -0,0 +1,11 @@
+# Georgi QWERTY/Steno firmware
+
+This is the default keymap for Georgi, it's based heavily off of the naps62 ErgoDox and the Gergo layout. 
+It is both a ergonomic and programmer friendly keymap.
+
+Ideally you should copy this directory and make your changes there. If you come up with a good layout submit a PR!
+
+## Space issues
+If you find yourself running out of space for dictionary entries, disabling mousekeys in rules.mk will save
+you about 4k for entries!
+Get a free 1k by deleting the Gaming layers from the keymap!