diff --git a/active/device_shelly/shelly.md b/active/device_shelly/shelly.md
index dc0869e..c83315e 100644
--- a/active/device_shelly/shelly.md
+++ b/active/device_shelly/shelly.md
@@ -1,5 +1,47 @@
 # Shelly Devices
 
+- [Shelly Devices](#shelly-devices)
+  - [1PM Mini Gen4](#1pm-mini-gen4)
+    - [Setup 1PM Mini Gen4](#setup-1pm-mini-gen4)
+    - [Install 1PM Mini Gen4](#install-1pm-mini-gen4)
+  - [Shelly Plug US](#shelly-plug-us)
+  - [Shelly BLU Motion](#shelly-blu-motion)
+  - [Shelly BLU Door/Window](#shelly-blu-doorwindow)
+    - [Reset](#reset)
+  - [Shelly Flood](#shelly-flood)
+
+## 1PM Mini Gen4
+
+### Setup 1PM Mini Gen4
+
+1. Cut 1 white and 3 black pieces of 14 gauge wire to 3" long.
+2. Strip 1/4" from one side of each wire.
+3. Strip 1/2" from the other side of each wire.
+4. Connect the 1/4" side to the shelly. Tighten the screws until you can't turn them.
+5. Push line and neutral into a standard outlet. The wider receptacle is neutral.
+6. Press and hold the button for 10 seconds to factory reset. Light will flash on/off every 1/4 second.
+7. Press and hold the button for 5 seconds to turn on AP mode. Light will flash on/off every 1/2 second.
+8. Connect to shelly network.
+9. Navigate to <http://192.168.33.1>.
+10. Connect to wifi. The light should turn solid.
+11. Update firmware.
+12. Set a password for AP mode.
+13. Turn off the AP.
+14. In Unifi: Name the device, give it a fixed IP, set the icon.
+15. Navigate to the Shelly website via its IP address.
+16. Set a password for http access: Settings -> Authentication.
+17. Name the device: Settings -> Device name.
+18. Set Restore last known state of output/relay: Home -> Output -> Input/Output Settings.
+19. Enable Zigbee: Zigbee -> Enable.
+20. Connect Shelly to Home Assistant via Zigbee.
+21. Change switch type: Click on switch control -> Settings -> Show as.
+
+### Install 1PM Mini Gen4
+
+1. Cut 1 3" white wire for neutral bridge.
+2. Cut 2 3" black wires for line bridge and light switch input.
+3. Prepare 4 14 gauge wire connectors.
+
 ## Shelly Plug US
 
 1. Connect to WiFi
@@ -11,8 +53,36 @@
 7. Enable Bluetooth Gateway
 8. Update Firmware
 
+## Shelly BLU Motion
+
+1. Download and install the Shelly Debug app
+2. Follow the instructions in the app to connect the device
+3. Update the firmware
+4. Enable encryption (generate a 6 digit code)
+5. "Read" from the device and copy the encryption key for home assistant
+
+## Shelly BLU Door/Window
+
+1. Download and install the Shelly Debug app
+2. Follow the instructions in the app to connect the device
+3. Update the firmware
+4. Create a new "login" in Bitwarden called "Shelly BLU DW " + name of device
+   1. Password will be the encryption key
+   2. Website should be the MAC address of the Shelly
+5. Generate a 6 digit code, send it to your phone then throw it away
+6. In the Shelly Debug app, enable encryption using the 6 digit code
+7. Copy the encryption and store in the password field
+8. Add to Home Assistant
+9. Unpair from Phone
+
 ### Reset
 
 Resetting is super finnicky. You'll need to plug it in, press and hold the power button until the
 red light flashes quickly (not slowly, that's a reboot). You'll probably have to do it multiple
-times because they seem to reboot halfway through the reset process.
\ No newline at end of file
+times because they seem to reboot halfway through the reset process.
+
+## Shelly Flood
+
+1. In the web interface, ensure "CoIoT" is enabled and pointing to `<home assistant ip>:5683`.
+   Allow 5683/udp from shelly flood to home assistant. If you don't do this Shelly Flood will
+   not report its status correctly!
\ No newline at end of file