Directly connected LED Matrix support.

This adds support for LEDs that are directly connected to the MCU, either in a matrix or to single pins.

common_features.mk

@@ -116,7 +116,7 @@ ifeq ($(strip $(RGBLIGHT_ENABLE)), yes)
     endif
 endif
 
-VALID_MATRIX_TYPES := yes IS31FL3731 IS31FL3733 IS31FL3737 WS2812 custom
+VALID_MATRIX_TYPES := yes IS31FL3731 IS31FL3733 IS31FL3737 WS2812 custom pins pinmatrix
 
 LED_MATRIX_ENABLE ?= no
 ifneq ($(strip $(LED_MATRIX_ENABLE)), no)
@@ -129,6 +129,20 @@ ifneq ($(strip $(LED_MATRIX_ENABLE)), no)
     endif
 endif
 
+ifeq ($(strip $(LED_MATRIX_ENABLE)), pinmatrix)
+    CIE1931_CURVE = yes
+    OPT_DEFS += -DLED_MATRIX_PINMATRIX_ENABLE
+    COMMON_VPATH += $(DRIVER_PATH)/led
+    SRC += led_matrix_pinmatrix.c
+endif
+
+ifeq ($(strip $(LED_MATRIX_ENABLE)), pins)
+    CIE1931_CURVE = yes
+    OPT_DEFS += -DLED_MATRIX_PINS_ENABLE
+    COMMON_VPATH += $(DRIVER_PATH)/led
+    SRC += led_matrix_pins.c
+endif
+
 ifeq ($(strip $(LED_MATRIX_ENABLE)), IS31FL3731)
     OPT_DEFS += -DIS31FL3731
     COMMON_VPATH += $(DRIVER_PATH)/issi
@@ -150,7 +164,7 @@ endif
 endif
 
 ifeq ($(strip $(RGB_MATRIX_ENABLE)), yes)
-	RGB_MATRIX_ENABLE = IS31FL3731
+    RGB_MATRIX_ENABLE = IS31FL3731
 endif
 
 ifeq ($(strip $(RGB_MATRIX_ENABLE)), IS31FL3731)
@@ -293,9 +307,9 @@ endif
 
 HAPTIC_ENABLE ?= no
 ifneq ($(strip $(HAPTIC_ENABLE)),no)
-	COMMON_VPATH += $(DRIVER_PATH)/haptic
-	SRC += haptic.c
-	OPT_DEFS += -DHAPTIC_ENABLE
+    COMMON_VPATH += $(DRIVER_PATH)/haptic
+    SRC += haptic.c
+    OPT_DEFS += -DHAPTIC_ENABLE
 endif
 
 ifneq ($(filter DRV2605L, $(HAPTIC_ENABLE)), )

docs/cli.md

@@ -125,14 +125,14 @@ This command examines your environment and alerts you to potential build or flas
 qmk doctor
 ```
 
-## `qmk list_keyboards`
+## `qmk list-keyboards`
 
 This command lists all the keyboards currently defined in `qmk_firmware`
 
 **Usage**:
 
 ```
-qmk list_keyboards
+qmk list-keyboards
 ```
 
 ## `qmk new-keymap`

docs/driver_installation_zadig.md

@@ -2,9 +2,9 @@
 
 QMK presents itself to the host as a regular HID keyboard device, and as such requires no special drivers. However, in order to flash your keyboard on Windows, the bootloader device that appears when you reset the board often *does*.
 
-There are two notable exceptions: the Caterina bootloader, usually seen on Pro Micros, and the Halfkay bootloader shipped with PJRC Teensys, appear as a serial port and a generic HID device respectively, and so do not require a driver.
+There are two notable exceptions: the Caterina bootloader, usually seen on Pro Micros, and the HalfKay bootloader shipped with PJRC Teensys, appear as a serial port and a generic HID device respectively, and so do not require a driver.
 
-We recommend the use of the [Zadig](https://zadig.akeo.ie/) utility. If you have set up the development environment with Msys2 or WSL, the `qmk_install.sh` script will have asked if you want it to install the drivers for you.
+We recommend the use of the [Zadig](https://zadig.akeo.ie/) utility. If you have set up the development environment with MSYS2 or WSL, the `qmk_install.sh` script will have asked if you want it to install the drivers for you.
 
 ## Installation
 
@@ -31,7 +31,7 @@ Finally, unplug and replug the keyboard to make sure the new driver has been loa
 
 ## Recovering from Installation to Wrong Device
 
-If you find that you can no longer type with the keyboard, you may have installed the driver onto the keyboard itself instead of the bootloader. You can easily confirm this in Zadig - a healthy keyboard has the `HidUsb` driver installed on all of its interfaces:
+If you find that you can no longer type with the keyboard, you may have accidentally replaced the driver for the keyboard itself instead of for the bootloader. This can happen when the keyboard is not in the bootloader mode. You can easily confirm this in Zadig - a healthy keyboard has the `HidUsb` driver installed on all of its interfaces:
 
 ![A healthy keyboard as seen by Zadig](https://i.imgur.com/Hx0E5kC.png)
 
@@ -44,3 +44,5 @@ Right-click it and hit **Uninstall device**. Make sure to tick **Delete the driv
 ![The Device Uninstall dialog, with the "delete driver" checkbox ticked](https://i.imgur.com/aEs2RuA.png)
 
 Click **Action → Scan for hardware changes**. At this point, you should be able to type again. Double check in Zadig that the keyboard device(s) are using the `HidUsb` driver. If so, you're all done, and your board should be functional again!
+
+?> A full reboot of your computer may sometimes be necessary at this point, to get Windows to pick up the new driver.

docs/feature_led_matrix.md

@@ -1,10 +1,66 @@
 # LED Matrix Lighting
 
-This feature allows you to use LED matrices driven by external drivers. It hooks into the backlight system so you can use the same keycodes as backlighting to control it.
+This feature allows you to use LED matrices driven by external drivers. It hooks into the [backlight subsystem](feature_backlight.md) so you can use the same keycodes as backlighting to control it. Many of the same configuration settings apply as well.
 
 If you want to use RGB LED's you should use the [RGB Matrix Subsystem](feature_rgb_matrix.md) instead.
 
-## Driver configuration
+LED Matrix supports LEDs that are connected directly to the MCU and LEDs connected to an external controller IC (such as the IS31FL3731 from ISSI.)
+
+## Directly Connected LEDs
+
+There are two ways that LEDs can be connected to the LED Matrix- 
+
+* Direct Pin: One pin per LED
+* Direct Pin Matrix: LED matrix with rows and columns
+
+### Direct Pin
+
+This driver uses LEDs that are connected directly to to a pin on the PCB. If you are not familiar with how to wire an LED directly to a microcontroller you can [follow this guide](https://create.arduino.cc/projecthub/rowan07/make-a-simple-led-circuit-ce8308). The process is similar for every microcontroller that QMK supports.
+
+You can configure the driver to either source or sink current, but that setting applies to all LEDs.
+
+Settings needed in `rules.mk`:
+
+| Variable | Description |
+|----------|-------------|
+| `BACKLIGHT_ENABLE = yes` | Turn on the backlight subsystem |
+| `LED_MATRIX_ENABLE = pins` | Enable the LED Matrix subsystem and configure it for directly connected LEDs |
+
+Settings needed in `config.h`:
+
+| Variable | Description | Default |
+|----------|-------------|---------|
+| `LED_MATRIX_PINS` | A list of pins with connected LEDs. | `{ }` |
+| `LED_DRIVER_LED_COUNT` | The number of LEDs connected to pins |
+
+### Direct Pin Matrix
+
+This driver supports driving an LED matrix that is connected directly to the local controller in a common-row cathode orientation. For more general information on LED matrices and how to design them there are several useful outside resources:
+
+* https://www.circuitspecialists.com/blog/build-8x8-led-matrix/
+* https://www.instructables.com/id/Make-Your-Own-LED-Matrix-/
+* https://appelsiini.net/2011/how-does-led-matrix-work/
+
+Settings needed in `rules.mk`:
+
+| Variable | Description |
+|----------|-------------|
+| `BACKLIGHT_ENABLE = yes` | Turn on the backlight subsystem |
+| `LED_MATRIX_ENABLE = pinmatrix` | Enable the LED Matrix subsystem and configure it for a matrix |
+
+Settings needed in `config.h`:
+
+| Variable | Description | Default |
+|----------|-------------|---------|
+| `LED_DRIVER_LED_COUNT` | (Required) How many LED lights are present | (none) |
+| `LED_MATRIX_COLS` | (Required) The number of columns (current sources) your matrix has | (none) |
+| `LED_MATRIX_COL_PINS` | (Required) A list of column pins, EG `{ B1, B2, B3, B4 }`| (none) |
+| `LED_MATRIX_ROWS` | (Required) The number of rows (current sinks) your matrix has | (none) |
+| `LED_MATRIX_ROW_PINS` | (Required) A list of row pins, EG `{ B5, B6, B7, B8 }` | (none) |
+
+## LED Driver ICs
+
+You can also use an LED driver chip. The IS31 series of ICs is popular and well supported in QMK.
 
 ### IS31FL3731
 

docs/hardware_avr.md

@@ -1,6 +1,6 @@
 # Keyboards with AVR Processors
 
-This page describes the support for for AVR processors in QMK. AVR processors include the atmega32u4, atmega32u2, at90usb1286, and other processors from Atmel Corporation. AVR processors are 8-bit MCU's that are designed to be easy to work with. The most common AVR processors in keyboards have on-board USB and plenty of GPIO for supporting large keyboard matrices. They are the most popular MCU for use in keyboards today.
+This page describes the support for for AVR processors in QMK. AVR processors include the atmega32u4, atmega32u2, at90usb1286, and other processors from Atmel Corporation. AVR processors are 8-bit MCUs that are designed to be easy to work with. The most common AVR processors in keyboards have on-board USB and plenty of GPIO for supporting large keyboard matrices. They are the most popular MCU for use in keyboards today.
 
 If you have not yet you should read the [Keyboard Guidelines](hardware_keyboard_guidelines.md) to get a sense of how keyboards fit into QMK.
 

docs/hardware_drivers.md

@@ -20,7 +20,7 @@ Support for SSD1306 based OLED displays. For more information see the [OLED Driv
 
 ## uGFX
 
-You can make use of uGFX within QMK to drive character and graphic LCD's, LED arrays, OLED, TFT, and other display technologies. This needs to be better documented, if you are trying to do this and reading the code doesn't help please [open an issue](https://github.com/qmk/qmk_firmware/issues/new) and we can help you through the process.
+You can make use of uGFX within QMK to drive character and graphic LCDs, LED arrays, OLED, TFT, and other display technologies. This needs to be better documented, if you are trying to do this and reading the code doesn't help please [open an issue](https://github.com/qmk/qmk_firmware/issues/new) and we can help you through the process.
 
 ## WS2812 (AVR Only)
 

docs/reference_glossary.md

@@ -1,16 +1,16 @@
 # Glossary of QMK Terms
 
 ## ARM
-A line of 32-bit MCU's produced by a number of companies, such as Atmel, Cypress, Kinetis, NXP, ST, and TI.
+A line of 32-bit MCUs produced by a number of companies, such as Atmel, Cypress, Kinetis, NXP, ST, and TI.
 
 ## AVR
-A line of 8-bit MCU's produced by [Atmel](http://www.microchip.com/). AVR was the original platform that TMK supported.
+A line of 8-bit MCUs produced by [Atmel](http://www.microchip.com/). AVR was the original platform that TMK supported.
 
 ## AZERTY
 The standard Français (French) keyboard layout. Named for the first 6 keys on the keyboard.
 
 ## Backlight
-A generic term for lighting on a keyboard. The backlight is typically, but not always, an array of LED's that shine through keycaps and/or switches.
+A generic term for lighting on a keyboard. The backlight is typically, but not always, an array of LEDs that shine through keycaps and/or switches.
 
 ## Bluetooth
 A short range peer to peer wireless protocol. Most common wireless protocol for a keyboard.
@@ -147,7 +147,7 @@ A feature that lets you assign multiple keycodes to the same key based on how ma
 A low-cost AVR development board that is commonly used for hand-wired builds. A teensy is often chosen despite costing a few dollars more due to its halfkay bootloader, which makes flashing very simple.
 
 ## Underlight
-A generic term for LEDs that light the underside of the board. These LED's typically shine away from the bottom of the PCB and towards the surface the keyboard rests on.
+A generic term for LEDs that light the underside of the board. These LEDs typically shine away from the bottom of the PCB and towards the surface the keyboard rests on.
 
 ## Unicode
 In the larger computer world Unicode is a set of encoding schemes for representing characters in any language. As it relates to QMK it means using various OS schemes to send unicode codepoints instead of scancodes.

docs/understanding_qmk.md

@@ -22,7 +22,7 @@ This section of code is called "The Main Loop" because it's responsible for loop
     keyboard_task();
 ```
 
-This is where all the keyboard specific functionality is dispatched. The source code for `keyboard_task()` can be found in [tmk_core/common/keyboard.c](https://github.com/qmk/qmk_firmware/blob/e1203a222bb12ab9733916164a000ef3ac48da93/tmk_core/common/keyboard.c#L216), and it is responsible for detecting changes in the matrix and turning status LED's on and off.
+This is where all the keyboard specific functionality is dispatched. The source code for `keyboard_task()` can be found in [tmk_core/common/keyboard.c](https://github.com/qmk/qmk_firmware/blob/e1203a222bb12ab9733916164a000ef3ac48da93/tmk_core/common/keyboard.c#L216), and it is responsible for detecting changes in the matrix and turning status LEDs on and off.
 
 Within `keyboard_task()` you'll find code to handle:
 
@@ -30,7 +30,7 @@ Within `keyboard_task()` you'll find code to handle:
 * Mouse Handling
 * Serial Link(s)
 * Visualizer
-* Keyboard status LED's (Caps Lock, Num Lock, Scroll Lock)
+* Keyboard status LEDs (Caps Lock, Num Lock, Scroll Lock)
 
 #### Matrix Scanning
 
@@ -175,7 +175,7 @@ FIXME: This needs to be written
 
 FIXME: This needs to be written
 
-#### Keyboard state LED's (Caps Lock, Num Lock, Scroll Lock)
+#### Keyboard state LEDs (Caps Lock, Num Lock, Scroll Lock)
 
 FIXME: This needs to be written
 

drivers/led/led_matrix_pinmatrix.c

@@ -0,0 +1,103 @@
+/* Copyright 2017 Jason Williams
+ * Copyright 2018 Jack Humbert
+ * Copyright 2019 Clueboard
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifdef __AVR__
+#    include <avr/interrupt.h>
+#    include <avr/io.h>
+#    include <util/delay.h>
+#    define led_wait_us(us) wait_us(us)
+#else
+#    include "ch.h"
+#    include "hal.h"
+#    define led_wait_us(us) chSysPolledDelayX(US2RTC(STM32_SYSCLK, us))
+#endif
+
+#include <stdint.h>
+#include <stdbool.h>
+#include <string.h>
+#include "led_matrix_pinmatrix.h"
+#include "led_tables.h"
+#include "progmem.h"
+#include "quantum.h"
+#include "backlight.h"
+
+
+/*
+ * g_pwm_buffer is an array that represents the duty cycle (0-255) for each LED.
+ * FIXME: Map this from the wiring matrix to a physical location matrix at some point
+ */
+uint8_t g_pwm_buffer[LED_MATRIX_ROWS * LED_MATRIX_COLS];
+const pin_t led_row_pins[LED_MATRIX_ROWS] = LED_MATRIX_ROW_PINS;
+const pin_t led_col_pins[LED_MATRIX_COLS] = LED_MATRIX_COL_PINS;
+
+
+void led_matrix_pinmatrix_init_pins(void) {
+    /* Set all pins to output, we are not interested in reading any information.
+     */
+    for (uint8_t x = 0; x < LED_MATRIX_ROWS; x++) {
+        setPinOutput(led_row_pins[x]);
+        writePinLow(led_row_pins[x]);
+    }
+
+    for (uint8_t x = 0; x < LED_MATRIX_COLS; x++) {
+        setPinOutput(led_col_pins[x]);
+        writePinLow(led_col_pins[x]);
+    }
+}
+
+void led_matrix_pinmatrix_set_value(int index, uint8_t value) {
+    /* Set the brighness for a single LED.
+     */
+    if (index >= 0 && index < LED_DRIVER_LED_COUNT) {
+        g_pwm_buffer[index] = value;
+    }
+}
+
+void led_matrix_pinmatrix_set_value_all(uint8_t value) {
+    /* Set the brighness for all LEDs.
+     */
+    for (int i = 0; i < LED_DRIVER_LED_COUNT; i++) {
+        led_matrix_pinmatrix_set_value(i, value);
+    }
+}
+
+void led_matrix_pinmatrix_flush(void) {
+    /* This is a basic bit-banged pwm implementation.
+     */
+    uint8_t led_count = 0;
+    for (uint8_t row = 0; row < LED_MATRIX_ROWS; row++) {
+        writePinLow(led_row_pins[row]);
+        for (uint8_t col = 0; col < LED_MATRIX_COLS; col++) {
+            /* We spend ~128us on each LED, dividing that time between lit and unlit.
+             */
+            const uint8_t brightness = pgm_read_byte(&CIE1931_CURVE[g_pwm_buffer[led_count]]) / 2;
+            if (brightness > 0) {
+                writePinHigh(led_col_pins[col]);
+                for (int i = 0; i < 128; i++) {
+                    if (i == brightness) {
+                        writePinLow(led_col_pins[col]);
+                    }
+                    led_wait_us(1);
+                }
+            } else {
+                led_wait_us(128);
+            }
+            led_count++;
+        }
+    }
+}

drivers/led/led_matrix_pinmatrix.h

@@ -0,0 +1,30 @@
+/* Copyright 2017 Jason Williams
+ * Copyright 2018 Jack Humbert
+ * Copyright 2019 Clueboard
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef LED_MATRIX_PINMATRIX_DRIVER_H
+#define LED_MATRIX_PINMATRIX_DRIVER_H
+
+void led_matrix_pinmatrix_init_pins(void);
+void led_matrix_pinmatrix_set_value(int index, uint8_t value);
+void led_matrix_pinmatrix_set_value_all(uint8_t value);
+void led_matrix_pinmatrix_flush(void);
+void led_matrix_pinmatrix_select_row(uint8_t row);
+void led_matrix_pinmatrix_unselect_row(uint8_t row);
+void led_matrix_pinmatrix_unselect_rows(void);
+
+#endif  // LED_MATRIX_PINMATRIX_DRIVER_H

drivers/led/led_matrix_pins.c

@@ -0,0 +1,95 @@
+/* Copyright 2017 Jason Williams
+ * Copyright 2018 Jack Humbert
+ * Copyright 2019 Clueboard
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifdef __AVR__
+#    include <avr/interrupt.h>
+#    include <avr/io.h>
+#    include <util/delay.h>
+#    define led_wait_us(us) wait_us(us)
+#else
+#    include "ch.h"
+#    include "hal.h"
+#    define led_wait_us(us) chSysPolledDelayX(US2RTC(STM32_SYSCLK, us))
+#endif
+
+#include <stdint.h>
+#include <stdbool.h>
+#include <string.h>
+#include "led_matrix_pins.h"
+#include "led_tables.h"
+#include "progmem.h"
+#include "quantum.h"
+#include "backlight.h"
+
+
+/*
+ * g_pwm_buffer is an array that represents the duty cycle (0-255) for each LED.
+ */
+uint8_t g_pwm_buffer[LED_DRIVER_LED_COUNT];
+const pin_t led_pins[LED_DRIVER_LED_COUNT] = LED_MATRIX_PINS;
+
+#ifdef LED_MATRIX_PIN_SINK
+#    define led_pin_on(pin) writePinLow(pin)
+#    define led_pin_off(pin) writePinHigh(pin)
+#else
+#    define led_pin_on(pin) writePinHigh(pin)
+#    define led_pin_off(pin) writePinLow(pin)
+#endif
+
+void led_matrix_pins_init_pins(void) {
+    /* Set all pins to output, we are not interested in reading any information.
+     */
+    for (uint8_t x = 0; x < LED_DRIVER_LED_COUNT; x++) {
+        setPinOutput(led_pins[x]);
+        led_pin_off(led_pins[x]);
+    }
+}
+
+void led_matrix_pins_set_value(int index, uint8_t value) {
+    /* Set the brighness for a single LED.
+     */
+    if (index >= 0 && index < LED_DRIVER_LED_COUNT) {
+        g_pwm_buffer[index] = value;
+    }
+}
+
+void led_matrix_pins_set_value_all(uint8_t value) {
+    /* Set the brighness for all LEDs.
+     */
+    for (int i = 0; i < LED_DRIVER_LED_COUNT; i++) {
+        led_matrix_pins_set_value(i, value);
+    }
+}
+
+void led_matrix_pins_flush(void) {
+    /* This is a basic bit-banged pwm implementation.
+     */
+    for (uint8_t i = 0; i < LED_DRIVER_LED_COUNT; i++) {
+        /* We spend ~1.3ms on each LED, dividing that time between lit and unlit.
+         */
+        if (g_pwm_buffer[i] > 0) {
+            uint8_t brightness = pgm_read_byte(&CIE1931_CURVE[g_pwm_buffer[i]]) / 2;
+            led_pin_on(led_pins[i]);
+            led_wait_us(brightness);
+            led_pin_off(led_pins[i]);
+            led_wait_us(128 - brightness);
+        } else {
+            led_wait_us(128);
+        }
+    }
+}

drivers/led/led_matrix_pins.h

@@ -0,0 +1,30 @@
+/* Copyright 2017 Jason Williams
+ * Copyright 2018 Jack Humbert
+ * Copyright 2019 Clueboard
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef LED_MATRIX_PINS_DRIVER_H
+#define LED_MATRIX_PINS_DRIVER_H
+
+void led_matrix_pins_init_pins(void);
+void led_matrix_pins_set_value(int index, uint8_t value);
+void led_matrix_pins_set_value_all(uint8_t value);
+void led_matrix_pins_flush(void);
+void led_matrix_pins_select_row(uint8_t row);
+void led_matrix_pins_unselect_row(uint8_t row);
+void led_matrix_pins_unselect_rows(void);
+
+#endif  // LED_MATRIX_PINS_DRIVER_H

keyboards/1upkeyboards/1up60rgb/info.json

@@ -14,7 +14,7 @@
     },
 
     "LAYOUT_60_iso": {
-      "layout": [{"label":"\u00ac", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"\"", "x":2, "y":0}, {"label":"\u00a3", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"label":"Backspace", "x":13, "y":0, "w":2}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"{", "x":11.5, "y":1}, {"label":"}", "x":12.5, "y":1}, {"label":"Enter", "x":13.75, "y":1, "w":1.25, "h":2}, {"label":"Caps Lock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"@", "x":11.75, "y":2}, {"label":"~", "x":12.75, "y":2}, {"label":"Shift", "x":0, "y":3, "w":1.25}, {"label":"|", "x":1.25, "y":3}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":2.75}, {"label":"Ctrl", "x":0, "y":4, "w":1.25}, {"label":"Win", "x":1.25, "y":4, "w":1.25}, {"label":"Alt", "x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.25}, {"label":"AltGr", "x":10, "y":4, "w":1.25}, {"label":"Win", "x":11.25, "y":4, "w":1.25}, {"label":"Menu", "x":12.5, "y":4, "w":1.25}, {"label":"Ctrl", "x":13.75, "y":4, "w":1.25}]
+      "layout": [{"label":"\u00ac", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"\"", "x":2, "y":0}, {"label":"\u00a3", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"label":"Backspace", "x":13, "y":0, "w":2}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"{", "x":11.5, "y":1}, {"label":"}", "x":12.5, "y":1}, {"label":"Caps Lock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"@", "x":11.75, "y":2}, {"label":"~", "x":12.75, "y":2}, {"label":"Enter", "x":13.75, "y":1, "w":1.25, "h":2}, {"label":"Shift", "x":0, "y":3, "w":1.25}, {"label":"|", "x":1.25, "y":3}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":2.75}, {"label":"Ctrl", "x":0, "y":4, "w":1.25}, {"label":"Win", "x":1.25, "y":4, "w":1.25}, {"label":"Alt", "x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.25}, {"label":"AltGr", "x":10, "y":4, "w":1.25}, {"label":"Win", "x":11.25, "y":4, "w":1.25}, {"label":"Menu", "x":12.5, "y":4, "w":1.25}, {"label":"Ctrl", "x":13.75, "y":4, "w":1.25}]
     },
 
     "LAYOUT_60_ansi_split_bs_rshift": {

keyboards/1upkeyboards/sweet16/config.h

@@ -4,8 +4,6 @@
 
 /* USB Device descriptor parameter */
 #define VENDOR_ID       0xFEED
-#define PRODUCT_ID      0x2010
-#define DEVICE_VER      0x0001
 #define MANUFACTURER    1up Keyboards
 #define PRODUCT         Sweet16
 #define DESCRIPTION     4x4 grid
@@ -14,34 +12,11 @@
 #define MATRIX_ROWS 4
 #define MATRIX_COLS 4
 
-/* key matrix pins */
-#define MATRIX_ROW_PINS { F4, F5, F6, F7 }
-#define MATRIX_COL_PINS { D1, D0, D4, C6 }
-#define UNUSED_PINS
-
-/* COL2ROW or ROW2COL */
-#define DIODE_DIRECTION COL2ROW
-
 /* number of backlight levels */
-
-#ifdef BACKLIGHT_PIN
-#define BACKLIGHT_LEVELS 3
-#endif
-
-/* Set 0 if debouncing isn't needed */
-#define DEBOUNCE 5
+#define BACKLIGHT_LEVELS 10
 
 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
 #define LOCKING_SUPPORT_ENABLE
 
 /* Locking resynchronize hack */
 #define LOCKING_RESYNC_ENABLE
-
-#define RGB_DI_PIN B1
-#ifdef RGB_DI_PIN
-#define RGBLIGHT_ANIMATIONS
-#define RGBLED_NUM 1
-#define RGBLIGHT_HUE_STEP 8
-#define RGBLIGHT_SAT_STEP 8
-#define RGBLIGHT_VAL_STEP 8
-#endif

keyboards/1upkeyboards/sweet16/info.json

@@ -1,7 +1,7 @@
 {
   "keyboard_name": "Sweet 16",
   "url": "",
-  "maintainer": "qmk",
+  "maintainer": "skullydazed",
   "width": 4,
   "height": 4,
   "layouts": {

keyboards/1upkeyboards/sweet16/keymaps/default/keymap.c

@@ -25,21 +25,15 @@ bool process_record_user(uint16_t keycode, keyrecord_t *record) {
     return true;
 }
 
-void led_set_user(uint8_t usb_led) {
-
-  #ifndef CONVERT_TO_PROTON_C
-  /* Map RXLED to USB_LED_NUM_LOCK */
-	if (usb_led & (1 << USB_LED_NUM_LOCK)) {
-		DDRB |= (1 << 0); PORTB &= ~(1 << 0);
-	} else {
-		DDRB &= ~(1 << 0); PORTB &= ~(1 << 0);
-	}
-
-  /* Map TXLED to USB_LED_CAPS_LOCK */
-	if (usb_led & (1 << USB_LED_CAPS_LOCK)) {
-		DDRD |= (1 << 5); PORTD &= ~(1 << 5);
-	} else {
-		DDRD &= ~(1 << 5); PORTD &= ~(1 << 5);
-	}
-  #endif
+#ifdef ENCODER_ENABLE
+#include "encoder.h"
+void encoder_update_user(int8_t index, bool clockwise) {
+  if (index == 0) { /* First encoder */
+    if (clockwise) {
+      tap_code(KC_VOLU);
+    } else {
+      tap_code(KC_VOLD);
+    }
+  }
 }
+#endif

keyboards/1upkeyboards/sweet16/keymaps/tester/keymap.c

@@ -0,0 +1,39 @@
+#include QMK_KEYBOARD_H
+
+enum custom_keycodes {
+  UP_URL = SAFE_RANGE
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+    LAYOUT_ortho_4x4(
+        KC_0,   KC_1,   KC_2,   KC_3,
+        KC_4,   KC_5,   KC_6,   KC_7,
+        KC_8,   KC_9,   KC_A,   KC_B,
+        KC_C,   RESET,  KC_E,   BL_STEP
+    )
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+    switch (keycode) {
+        case UP_URL:
+            if (record->event.pressed) {
+                SEND_STRING("http://1upkeyboards.com");
+            }
+            return false;
+            break;
+    }
+    return true;
+}
+
+#ifdef ENCODER_ENABLE
+#include "encoder.h"
+void encoder_update_user(int8_t index, bool clockwise) {
+  if (index == 0) { /* First encoder */
+    if (clockwise) {
+      tap_code(KC_VOLU);
+    } else {
+      tap_code(KC_VOLD);
+    }
+  }
+}
+#endif

keyboards/1upkeyboards/sweet16/readme.md

@@ -1,13 +1,12 @@
 # Sweet 16 Macropad
 
-A 4x4 numpad/macro pad sold by 1up Keyboards - designed by Bishop Keyboards
+A 4x4 numpad/macro pad sold by 1up Keyboards.
 
-Keyboard Maintainer: QMK Community  
-Hardware Supported: Sweet16 Keyboard PCB  
-Hardware Availability: [1up Keyboards](https://1upkeyboards.com/)
+* Keyboard Maintainer: skullydazed
+* Hardware Supported: Sweet16 Keyboard PCB
+* Hardware Availability: [1up Keyboards](https://1upkeyboards.com/)
 
-Make example for this keyboard (after setting up your build environment):
-
-    make 1upkeyboards/sweet16:default
-
-See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
+Revisions:
+* [v1](./v1/)- The original macropad, designed by Bishop Keyboards
+* [v2/promicro](./v2/promicro)- The second macropad built with a Pro Micro, designed by Clueboard
+* [v2/proton_c](./v2/proton_c)- The second macropad built with a Proton C, designed by Clueboard

keyboards/1upkeyboards/sweet16/rules.mk

@@ -1,27 +1,12 @@
-# MCU name
-MCU = atmega32u4
-
-# Bootloader selection
-#   Teensy       halfkay
-#   Pro Micro    caterina
-#   Atmel DFU    atmel-dfu
-#   LUFA DFU     lufa-dfu
-#   QMK DFU      qmk-dfu
-#   ATmega32A    bootloadHID
-#   ATmega328P   USBasp
-BOOTLOADER = caterina
-
 # Build Options
-#   comment out to disable the options.
 #
-BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes  # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes  # Audio control and System control(+450)
-CONSOLE_ENABLE = no    # Console for debug(+400)
+DEFAULT_FOLDER = 1upkeyboards/sweet16/v1
+#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration
+MOUSEKEY_ENABLE = yes  # Mouse keys
+EXTRAKEY_ENABLE = yes  # Audio control and System control
+CONSOLE_ENABLE = no    # Console for debug
 COMMAND_ENABLE = no    # Commands for debug and configuration
 SLEEP_LED_ENABLE = no  # Breathing sleep LED during USB suspend
 NKRO_ENABLE = yes      # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE = no  # Enable keyboard backlight functionality
 AUDIO_ENABLE = no
-RGBLIGHT_ENABLE = yes
-EXTRAFLAGS += -flto
+RGBLIGHT_ENABLE = no

keyboards/1upkeyboards/sweet16/sweet16.c

@@ -1 +0,0 @@
-#include "sweet16.h"

keyboards/1upkeyboards/sweet16/v1/config.h

@@ -0,0 +1,28 @@
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define PRODUCT_ID      0x2010
+#define DEVICE_VER      0x0001
+
+/* key matrix pins */
+#define MATRIX_ROW_PINS { F4, F5, F6, F7 }
+#define MATRIX_COL_PINS { D1, D0, D4, C6 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+/* Set 0 if debouncing isn't needed */
+#define DEBOUNCE 5
+
+/* Underglow options */
+#define RGB_DI_PIN B1
+#ifdef RGB_DI_PIN
+#define RGBLIGHT_ANIMATIONS
+#define RGBLED_NUM 1
+#define RGBLIGHT_HUE_STEP 8
+#define RGBLIGHT_SAT_STEP 8
+#define RGBLIGHT_VAL_STEP 8
+#endif

keyboards/1upkeyboards/sweet16/v1/readme.md

@@ -0,0 +1,13 @@
+# Sweet16 V1
+
+A 4x4 numpad/macro pad sold by 1up Keyboards - designed by Bishop Keyboards
+
+* Keyboard Maintainer: QMK Community
+* Hardware Supported: Sweet16 V1 PCB
+* Hardware Availability: [1up Keyboards](https://1upkeyboards.com/)
+
+Make example for this keyboard (after setting up your build environment):
+
+    make 1upkeyboards/sweet16/v1:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/1upkeyboards/sweet16/v1/rules.mk

@@ -0,0 +1,5 @@
+MCU = atmega32u4
+BOOTLOADER = caterina
+LINK_TIME_OPTIMIZATION_ENABLE=yes
+RGBLIGHT_ENABLE = yes
+BACKLIGHT_ENABLE = no  # Enable keyboard backlight functionality

keyboards/1upkeyboards/sweet16/v1/v1.c

@@ -0,0 +1,21 @@
+#include "v1.h"
+
+void led_set_kb(uint8_t usb_led) {
+#ifndef CONVERT_TO_PROTON_C
+    /* Map RXLED to USB_LED_NUM_LOCK */
+    if (IS_LED_ON(usb_led, USB_LED_NUM_LOCK)) {
+        setPinOutput(B0);
+        writePinLow(B0);
+    } else {
+        setPinInput(B0);
+    }
+
+    /* Map TXLED to USB_LED_CAPS_LOCK */
+    if (IS_LED_ON(usb_led, USB_LED_CAPS_LOCK)) {
+        setPinOutput(D5);
+        writePinLow(D5);
+    } else {
+        setPinInput(D5);
+    }
+#endif
+}

keyboards/1upkeyboards/sweet16/v2/promicro/config.h

@@ -0,0 +1,39 @@
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define PRODUCT_ID      0x2011
+#define DEVICE_VER      0x0001
+
+/* key matrix pins */
+#define MATRIX_ROW_PINS { D4, D1, E6, B5 }
+#define MATRIX_COL_PINS { F7, F6, D2, D3 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION ROW2COL
+
+/* Set 0 if debouncing isn't needed */
+#define DEBOUNCE 5
+
+/* Backlight configuration
+ */
+#define LED_MATRIX_ROWS 4
+#define LED_MATRIX_ROW_PINS { B1, B3, B2, B4 }
+#define LED_MATRIX_COLS 4
+#define LED_MATRIX_COL_PINS { B6, D0, C6, D7 }
+#define LED_DRIVER_LED_COUNT 16
+
+/* Encoder pins */
+#define ENCODERS_PAD_A { F4 }
+#define ENCODERS_PAD_B { F5 }
+#define ENCODER_RESOLUTION 4
+
+/* Underglow options */
+#define RGB_DI_PIN F4
+#define RGBLIGHT_ANIMATIONS
+#define RGBLED_NUM 1
+#define RGBLIGHT_HUE_STEP 8
+#define RGBLIGHT_SAT_STEP 8
+#define RGBLIGHT_VAL_STEP 8

keyboards/1upkeyboards/sweet16/v2/promicro/promicro.c

@@ -0,0 +1,8 @@
+#include "promicro.h"
+#include "encoder.h"
+
+#ifdef ENCODER_ENABLED
+void encoder_update_kb(int8_t index, bool clockwise) {
+    encoder_update_user(index, clockwise);
+}
+#endif

keyboards/1upkeyboards/sweet16/v2/promicro/promicro.h

@@ -0,0 +1,30 @@
+#pragma once
+
+#include "quantum.h"
+
+// Any changes to the layout names and/or definitions must also be made to info.json
+
+#define LAYOUT_ortho_4x4( \
+    K00, K01, K02, K03, \
+    K10, K11, K12, K13, \
+    K20, K21, K22, K23, \
+    K30, K31, K32, K33  \
+) { \
+    { K00,   K01,   K02,   K03 }, \
+    { K10,   K11,   K12,   K13 }, \
+    { K20,   K21,   K22,   K23 }, \
+    { K30,   K31,   K32,   K33 }  \
+}
+
+#define LAYOUT_numpad_4x4( \
+    K00, K01, K02, K03, \
+    K10, K11, K12,      \
+    K20, K21, K22, K23, \
+       K31,   K32      \
+) { \
+    { K00,   K01,   K02,   K03 }, \
+    { K10,   K11,   K12,   KC_NO }, \
+    { K20,   K21,   K22,   K23 }, \
+    { KC_NO, K31,   K32,   KC_NO }  \
+}
+

keyboards/1upkeyboards/sweet16/v2/promicro/readme.md

@@ -0,0 +1,13 @@
+# Sweet16 V2 (Pro Micro)
+
+A 4x4 numpad/macro pad sold by 1up Keyboards - designed by Clueboard
+
+* Keyboard Maintainer: skullydazed
+* Hardware Supported: Sweet16 V2 PCB, Pro Micro
+* Hardware Availability: [1up Keyboards](https://1upkeyboards.com/)
+
+Make example for this keyboard (after setting up your build environment):
+
+    make 1upkeyboards/sweet16/v2/promicro:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/1upkeyboards/sweet16/v2/promicro/rules.mk

@@ -0,0 +1,12 @@
+MCU = atmega32u4
+BOOTLOADER = caterina
+LINK_TIME_OPTIMIZATION_ENABLE=yes
+
+## Features
+BACKLIGHT_ENABLE = yes
+LED_MATRIX_ENABLE = pinmatrix
+CONSOLE_ENABLE = yes
+
+## On a Pro Micro you have to choose between underglow and the rotary encoder.
+RGBLIGHT_ENABLE = no
+ENCODER_ENABLE = yes

keyboards/1upkeyboards/sweet16/v2/proton_c/config.h

@@ -0,0 +1,28 @@
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define PRODUCT_ID      0x2011
+#define DEVICE_VER      0x0001
+
+/* key matrix pins */
+#define MATRIX_ROW_PINS { B5, B7, B2, B0 }
+#define MATRIX_COL_PINS { B8, A0, A10, A9 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION ROW2COL
+
+/* Backlight configuration
+ */
+#define LED_MATRIX_ROWS 4
+#define LED_MATRIX_ROW_PINS { B13, B14, B15, B1 }
+#define LED_MATRIX_COLS 4
+#define LED_MATRIX_COL_PINS { B9, B6, B4, B3 }
+#define LED_DRIVER_LED_COUNT 16
+
+/* Encoder pins */
+#define ENCODERS_PAD_A { A2 }
+#define ENCODERS_PAD_B { A1 }
+#define ENCODER_RESOLUTION 4

keyboards/1upkeyboards/sweet16/v2/proton_c/proton_c.c

@@ -0,0 +1 @@
+#include "proton_c.h"

keyboards/1upkeyboards/sweet16/v2/proton_c/proton_c.h

@@ -0,0 +1,30 @@
+#pragma once
+
+#include "quantum.h"
+
+// Any changes to the layout names and/or definitions must also be made to info.json
+
+#define LAYOUT_ortho_4x4( \
+    K00, K01, K02, K03, \
+    K10, K11, K12, K13, \
+    K20, K21, K22, K23, \
+    K30, K31, K32, K33  \
+) { \
+    { K00,   K01,   K02,   K03 }, \
+    { K10,   K11,   K12,   K13 }, \
+    { K20,   K21,   K22,   K23 }, \
+    { K30,   K31,   K32,   K33 }  \
+}
+
+#define LAYOUT_numpad_4x4( \
+    K00, K01, K02, K03, \
+    K10, K11, K12,      \
+    K20, K21, K22, K23, \
+       K31,   K32      \
+) { \
+    { K00,   K01,   K02,   K03 }, \
+    { K10,   K11,   K12,   KC_NO }, \
+    { K20,   K21,   K22,   K23 }, \
+    { KC_NO, K31,   K32,   KC_NO }  \
+}
+

keyboards/1upkeyboards/sweet16/v2/proton_c/readme.md

@@ -0,0 +1,13 @@
+# Sweet16 V2 (Proton C)
+
+A 4x4 numpad/macro pad sold by 1up Keyboards - designed by Clueboard
+
+* Keyboard Maintainer: skullydazed
+* Hardware Supported: Sweet16 V2 PCB, Proton C
+* Hardware Availability: [1up Keyboards](https://1upkeyboards.com/)
+
+Make example for this keyboard (after setting up your build environment):
+
+    make 1upkeyboards/sweet16/v2/proton_c:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/1upkeyboards/sweet16/v2/proton_c/rules.mk

@@ -0,0 +1,8 @@
+MCU = STM32F303
+
+## Features
+CONSOLE_ENABLE = yes
+BACKLIGHT_ENABLE = yes
+LED_MATRIX_ENABLE = pinmatrix
+ENCODER_ENABLE = yes
+AUDIO_ENABLE = yes

keyboards/40percentclub/4pack/4pack.c

@@ -0,0 +1,54 @@
+/* Copyright 2019 Arda Kilicdagi
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "4pack.h"
+
+// Optional override functions below.
+// You can leave any or all of these undefined.
+// These are only required if you want to perform custom actions.
+
+void matrix_init_kb(void) {
+  // put your keyboard start-up code here
+  // runs once when the firmware starts up
+
+  setPinOutput(F4); // cathodes
+  setPinOutput(F5); // cathodes
+
+  // Do the rest
+  matrix_init_user();
+}
+
+/*
+void matrix_scan_kb(void) {
+  // put your looping keyboard code here
+  // runs every cycle (a lot)
+
+  matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+  // put your per-action keyboard code here
+  // runs for every action, just before processing by the firmware
+
+  return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+  // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+  led_set_user(usb_led);
+}
+
+*/

keyboards/40percentclub/4pack/4pack.h

@@ -0,0 +1,33 @@
+/* Copyright 2019 Arda Kilicdagi
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+#define LAYOUT( \
+    k00, k01, k02, k03 \
+) \
+{ \
+    { k00, k01, k02, k03 }, \
+}

keyboards/40percentclub/4pack/config.h

@@ -0,0 +1,257 @@
+/*
+Copyright 2019 Arda Kilicdagi
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID 0xFEED
+#define PRODUCT_ID 0x0000
+#define DEVICE_VER 0x0001
+#define MANUFACTURER 40percentclub
+#define PRODUCT 4pack
+#define DESCRIPTION A 1x4 custom macropad
+
+/* key matrix size */
+#define MATRIX_ROWS 1
+#define MATRIX_COLS 4
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+ */
+// #define MATRIX_ROW_PINS { B0 } // B0 equivalents the ground pin
+// #define MATRIX_COL_PINS { E6, D7, C6, D4 }
+#define DIRECT_PINS { \
+    { E6, D7, C6, D4 } \
+}
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL*/
+#define DIODE_DIRECTION COL2ROW
+
+
+/*
+ * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.
+ */
+// #define SOFT_SERIAL_PIN D0  // or D1, D2, D3, E6
+
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+#define BACKLIGHT_LED_COUNT 2
+#undef BACKLIGHT_PIN
+#define BACKLIGHT_PINS { F6, F7 }
+
+
+// #define RGB_DI_PIN E2
+// #ifdef RGB_DI_PIN
+//   #define RGBLED_NUM 16
+//   #define RGBLIGHT_HUE_STEP 8
+//   #define RGBLIGHT_SAT_STEP 8
+//   #define RGBLIGHT_VAL_STEP 8
+//   #define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */
+//   #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
+// /*== all animations enable ==*/
+//   #define RGBLIGHT_ANIMATIONS
+// /*== or choose animations ==*/
+//   #define RGBLIGHT_EFFECT_BREATHING
+//   #define RGBLIGHT_EFFECT_RAINBOW_MOOD
+//   #define RGBLIGHT_EFFECT_RAINBOW_SWIRL
+//   #define RGBLIGHT_EFFECT_SNAKE
+//   #define RGBLIGHT_EFFECT_KNIGHT
+//   #define RGBLIGHT_EFFECT_CHRISTMAS
+//   #define RGBLIGHT_EFFECT_STATIC_GRADIENT
+//   #define RGBLIGHT_EFFECT_RGB_TEST
+//   #define RGBLIGHT_EFFECT_ALTERNATING
+// /*== customize breathing effect ==*/
+//   /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/
+//   #define RGBLIGHT_BREATHE_TABLE_SIZE 256      // 256(default) or 128 or 64
+//   /*==== use exp() and sin() ====*/
+//   #define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85  // 1 to 2.7
+//   #define RGBLIGHT_EFFECT_BREATHE_MAX    255   // 0 to 255
+// #endif
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCE 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+/* defined by default; to change, uncomment and set to the combination you want */
+// #define IS_COMMAND() (get_mods() == MOD_MASK_SHIFT)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP           H
+//#define MAGIC_KEY_HELP_ALT       SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER0_ALT     GRAVE
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     B
+//#define MAGIC_KEY_BOOTLOADER_ALT ESC
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_EEPROM_CLEAR   BSPACE
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
+#endif
+*/
+
+/* Bootmagic Lite key configuration */
+// #define BOOTMAGIC_LITE_ROW 0
+// #define BOOTMAGIC_LITE_COLUMN 0

keyboards/40percentclub/4pack/info.json

@@ -0,0 +1,12 @@
+{
+    "keyboard_name": "4pack", 
+    "url": "", 
+    "maintainer": "qmk", 
+    "width": 4, 
+    "height": 1, 
+    "layouts": {
+        "LAYOUT": {
+            "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}]
+        }
+    }
+}

keyboards/40percentclub/4pack/keymaps/default/config.h

@@ -0,0 +1,19 @@
+/* Copyright 2019 Arda Kilicdagi
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here

keyboards/40percentclub/4pack/keymaps/default/keymap.c

@@ -0,0 +1,26 @@
+/* Copyright 2019 Arda Kilicdagi
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+    [0] = LAYOUT( /* Base */
+        KC_A, KC_S, KC_D, KC_F
+    ),
+};
+
+
+void matrix_init_user(void) { }

keyboards/40percentclub/4pack/keymaps/default/readme.md

@@ -0,0 +1 @@
+# The default keymap for 4pack

keyboards/40percentclub/4pack/readme.md

@@ -0,0 +1,17 @@
+# 4 Pack
+
+![4pack](https://i.imgur.com/rioXXq5l.jpg)
+
+A 4-key macropad PCB with its switch and LED pins wired directly to microcontroller IO pins.
+
+You can find the main blog post about this macropad [here](http://www.40percent.club/2017/07/4-pack.html), also the Gerber files and other documentation is located [here](https://git.40percent.club/di0ib/Misc/src/branch/master/4pack).
+
+Keyboard Maintainer: [Arda Kilicdagi](http://github.com/ardakilic), [The QMK Community](https://github.com/qmk)  
+Hardware Supported: 4 Pack PCB, Pro Micro  
+Hardware Availability: [40percent.club](https://git.40percent.club/di0ib/Misc/src/branch/master/4pack)
+
+Make example for this macropad (after setting up your build environment):
+
+    make 40percentclub/4pack:default:flash
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/40percentclub/4pack/rules.mk

@@ -0,0 +1,33 @@
+# MCU name
+MCU = atmega32u4
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = caterina
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration
+MOUSEKEY_ENABLE = no        # Mouse keys
+EXTRAKEY_ENABLE = yes       # Audio control and System control
+CONSOLE_ENABLE = no         # Console for debug
+COMMAND_ENABLE = no         # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = yes      # Enable keyboard backlight functionality
+RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no         # Enable support for HD44780 based LCDs

keyboards/blackplum/blackplum.c

@@ -0,0 +1 @@
+#include "blackplum.h"

keyboards/blackplum/blackplum.h

@@ -0,0 +1,22 @@
+#pragma once
+
+#include "quantum.h"
+
+#define LAYOUT_68_ansi( \
+	K00, K10, K01, K11, K02, K12, K03, K13, K04, K14, K05, K15, K06, K16, K07, K17, \
+    K20, K30, K21, K31, K22, K32, K23, K33, K24, K34, K25, K35, K26, K36, K27, K37, \
+    K40, K50, K41, K51, K42, K52, K43, K53, K44, K54, K45, K55, K46, \
+    K60, K70, K61, K71, K62, K72, K63, K73, K64, K74, K65, K75, K66,  \
+    K80,      K81,      K82,      K83,      K84,      K85,      K86,	 K76, K67, K77\
+) { \
+	{ K00,   K01,   K02,   K03,   K04,   K05,   K06,   K07 }, \
+	{ K10,   K11,   K12,   K13,   K14,   K15,   K16,   K17 }, \
+	{ K20,   K21,   K22,   K23,   K24,   K25,   K26,   K27 }, \
+	{ K30,   K31,   K32,   K33,   K34,   K35,   K36,   K37 }, \
+	{ K40,   K41,   K42,   K43,   K44,   K45,   K46 }, \
+	{ K50,   K51,   K52,   K53,   K54,   K55 }, \
+	{ K60,   K61,   K62,   K63,   K64,   K65,   K66,   K67 }, \
+	{ K70,   K71,   K72,   K73,   K74,	 K75,	K76,   K77 }, \
+	{ K80,   K81,   K82,   K83,   K84,	 K85,	K86 } \
+}
+

keyboards/blackplum/config.h

@@ -0,0 +1,39 @@
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0xFADE
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Pixlup
+#define PRODUCT         Blackplum Keeb
+#define DESCRIPTION     Blackplum 68 Percent Mechanical Keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 9
+#define MATRIX_COLS 8
+
+/* key matrix pins */
+#define MATRIX_ROW_PINS { C6, B6, B4, B5, D6, D7, D5, D3, D4 }
+#define MATRIX_COL_PINS { D0, D1, D2, F7, F6, F5, F4, F1 }
+#define UNUSED_PINS
+
+/* Set 0 if debouncing isn't needed */
+#define DEBOUNCE 5
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+
+/* ws2812 RGB LED */
+#define RGB_DI_PIN C7
+#define RGBLIGHT_ANIMATIONS
+#define RGBLED_NUM 16    // Number of LEDs
+#define RGBLIGHT_HUE_STEP 10
+#define RGBLIGHT_SAT_STEP 10
+#define RGBLIGHT_VAL_STEP 10
+#define RGBLIGHT_SLEEP

keyboards/blackplum/info.json

@@ -0,0 +1,12 @@
+{
+    "keyboard_name": "blackplum",
+    "url": "www.tokopedia.com/pixlup",
+    "maintainer": "eriqadams",
+    "width": 17.25,
+    "height": 5.25,
+     "layouts": {
+        "LAYOUT_68_ansi": {
+            "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"label":"Backspace", "x":13, "y":0, "w":2}, {"label":"Insert", "x":15.25, "y":0}, {"label":"PgUp", "x":16.25, "y":0}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"{", "x":11.5, "y":1}, {"label":"}", "x":12.5, "y":1}, {"label":"|", "x":13.5, "y":1, "w":1.5}, {"label":"Delete", "x":15.25, "y":1}, {"label":"PgDn", "x":16.25, "y":1}, {"label":"Caps Lock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"label":"Enter", "x":12.75, "y":2, "w":2.25}, {"label":"Shift", "x":0, "y":3, "w":2.25}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":2.75}, {"label":"\u2191", "x":15.25, "y":3.25}, {"label":"Ctrl", "x":0, "y":4, "w":1.25}, {"label":"OS", "x":1.25, "y":4, "w":1.25}, {"label":"Alt", "x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.25}, {"label":"Alt", "x":10, "y":4, "w":1.25}, {"label":"Fn", "x":11.25, "y":4, "w":1.25}, {"label":"Ctrl", "x":12.5, "y":4, "w":1.25}, {"label":"\u2190", "x":14.25, "y":4.25}, {"label":"\u2193", "x":15.25, "y":4.25}, {"label":"\u2192", "x":16.25, "y":4.25}]
+        }
+    }
+}

keyboards/blackplum/keymaps/default/keymap.c

@@ -0,0 +1,43 @@
+#include QMK_KEYBOARD_H
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+#define _BASE 0
+#define _FN 1
+
+
+
+enum custom_keycodes {
+  TG_GUI = SAFE_RANGE
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  [_BASE] = LAYOUT_68_ansi(
+    KC_GESC, 	KC_1,    	KC_2,    	KC_3,    KC_4,    	KC_5,    KC_6,    KC_7,    	KC_8,    	KC_9,    	KC_0,    	KC_MINS, 	KC_EQL,  	KC_BSPC, 	KC_INS,		KC_PGUP,\
+    KC_TAB,  	KC_Q,    	KC_W,    	KC_E,    KC_R,    	KC_T,    KC_Y,    KC_U,    	KC_I,    	KC_O,    	KC_P,    	KC_LBRC, 	KC_RBRC, 	KC_BSLS, 	KC_DEL,		KC_PGDOWN,\
+    KC_CAPS, 	KC_A,    	KC_S,    	KC_D,    KC_F,    	KC_G,    KC_H,    KC_J,    	KC_K,    	KC_L,    	KC_SCLN, 	KC_QUOT, 				KC_ENT,\
+    KC_LSFT, 	KC_Z,    	KC_X,    	KC_C,    KC_V,    	KC_B,    KC_N,    KC_M,    	KC_COMM, 				KC_DOT,  	KC_SLSH, 				KC_RSFT,	KC_UP,\
+    KC_LCTL , 	KC_LGUI , 	KC_LALT ,                      	KC_SPC ,											KC_RALT , 	MO(_FN) ,	KC_RCTL, 	KC_LEFT,	KC_DOWN,	KC_RIGHT
+  ),
+
+  [_FN] = LAYOUT_68_ansi(
+    KC_GRV, 	KC_F1,   	KC_F2,   	KC_F3,   KC_F4,   	KC_F5,   KC_F6,   KC_F7,   	KC_F8,   	KC_F9,   	KC_F10,  	KC_F11,  	KC_F12,  	_______,	KC_MPLY,	KC_HOME,\
+    _______, 	RGB_MOD, 	RGB_HUI,   	RGB_SAI, RGB_VAI, 	_______, _______, _______, 	_______, 	_______, 	KC_PSCR, 	KC_SLCK, 	KC_PAUSE,  	_______,	KC_MUTE,	KC_END,\
+    _______,	RGB_TOG, 	RGB_HUD, 	RGB_SAD, RGB_VAD, 	_______, _______, _______, 	_______, 	_______, 	_______, 	_______, 				_______,\
+    _______,	_______, 	_______, 	_______, _______, 	_______, _______, _______,	_______, 				_______, 	_______, 				_______,	KC_VOLU,\
+    _______, 	TG_GUI,_______, 						RESET, 												_______,	_______,	_______,	KC_MPRV,    KC_VOLD, 	KC_MNXT
+  )
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+    if(record->event.pressed) {
+        switch(keycode) {
+            case TG_GUI:
+                keymap_config.no_gui ^= 1;
+                return false;
+        }
+    }
+    return true;
+}

keyboards/blackplum/readme.md

@@ -0,0 +1,14 @@
+# Blackplum
+![Blackplum](https://i.imgur.com/EOUQk4J.png)
+
+Blackplum a.k.a IMKG68 (which IMKG stands for Indonesian Mechanical Keyboard Group) is an 68% mechanical keyboard with RGB Underglow come with new layout you have never seen before. Recently the pcb and kits only available for purchase in Indonesia.
+
+Keyboard Maintainer: [eriqadams](https://github.com/eriqadams)  
+Hardware Supported: Blackplum PCB, ATMEGA32u4-au MCU  
+Hardware Availability: [If you're in Indonesia you can purchase here](https://tokopedia.com/pixlup) 
+
+Make example for this keyboard (after setting up your build environment):
+
+    make blackplum:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/blackplum/rules.mk

@@ -0,0 +1,27 @@
+# MCU name
+MCU = atmega32u4
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+BOOTLOADER = qmk-dfu
+
+# Build Options
+#   comment out to disable the options.
+#
+BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration
+MOUSEKEY_ENABLE = yes	  # Mouse keys
+EXTRAKEY_ENABLE = yes	  # Audio control and System control
+CONSOLE_ENABLE = no			# Console for debug
+COMMAND_ENABLE = no     # Commands for debug and configuration
+SLEEP_LED_ENABLE = no   # Breathing sleep LED during USB suspend
+NKRO_ENABLE = yes				# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no  # Enable keyboard backlight functionality
+AUDIO_ENABLE = no
+RGBLIGHT_ENABLE = yes
+
+LAYOUTS = 68_ansi

keyboards/clueboard/california/california.c

@@ -0,0 +1 @@
+#include "california.h"

keyboards/clueboard/california/california.h

@@ -0,0 +1,21 @@
+#pragma once
+
+#include "quantum.h"
+
+// Any changes to the layout names and/or definitions must also be made to info.json
+
+#define LAYOUT( \
+    K00, K01, \
+    K10, K11, \
+         K21, \
+    K30, K31, \
+    K40, K41, \
+         K51 \
+) { \
+    { K00, K01 }, \
+    { K10, K11 }, \
+    { KC_NO, K21 }, \
+    { K30, K31 }, \
+    { K40, K41 }, \
+    { KC_NO, K51 }  \
+}

keyboards/clueboard/california/config.h

@@ -0,0 +1,30 @@
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xC1ED
+#define PRODUCT_ID      0x23B0
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Clueboard
+#define PRODUCT         California Macropad
+#define DESCRIPTION     A 10-key macropad shaped like California
+
+/* key matrix pins */
+#define MATRIX_ROWS 6
+#define MATRIX_COLS 2
+#define DIRECT_PINS { \
+    { A10, A9 }, \
+    { A0, B8 }, \
+    { NO_PIN, B11 }, \
+    { B9, A8 }, \
+    { A7, B1 }, \
+    { NO_PIN, B2 } \
+}
+#define UNUSED_PINS
+
+/* Backlight configuration
+ */
+#define BACKLIGHT_LEVELS 10
+#define LED_MATRIX_PINS { A2, B5, A1, B4, B12, B10, A15, A6, B0, B3 }
+#define LED_DRIVER_LED_COUNT 10

keyboards/clueboard/california/info.json

@@ -0,0 +1,10 @@
+{
+    "keyboard_name": "Clueboard California",
+    "url": "",
+    "maintainer": "skullydazed",
+    "layouts": {
+        "LAYOUT": {
+            "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":0, "y":1}, {"x":1, "y":1}, {"x":1, "y":2}, {"x":1.25, "y":3}, {"x":2.25, "y":3}, {"x":2, "y":4}, {"x":3, "y":4}, {"x":3.75, "y":5}]
+        }
+    }
+}

keyboards/clueboard/california/keymaps/default/keymap.json

@@ -0,0 +1,7 @@
+{
+    "keyboard":"clueboard/california",
+    "layout":"LAYOUT",
+    "layers":[
+        ["KC_1","KC_2","KC_3","KC_4","KC_5","KC_6","KC_7","KC_8","KC_9","BL_STEP"]
+    ]
+}

keyboards/clueboard/california/readme.md

@@ -0,0 +1,13 @@
+# Clueboard California
+
+A macropad shaped like California
+
+* Keyboard Maintainer: [Zach White](https://github.com/skullydazed)
+* Hardware Supported: Clueboard California PCB
+* Hardware Availability: 2019 Northern California Meetup
+
+Make example for this keyboard (after setting up your build environment):
+
+    make clueboard/california:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/clueboard/california/rules.mk

@@ -0,0 +1,12 @@
+MCU = STM32F303
+
+## Features
+MOUSEKEY_ENABLE = yes  # Mouse keys
+EXTRAKEY_ENABLE = yes  # Audio control and System control
+CONSOLE_ENABLE = yes   # Console for debug
+COMMAND_ENABLE = no    # Commands for debug and configuration
+NKRO_ENABLE = yes      # USB Nkey Rollover
+BACKLIGHT_ENABLE = yes
+LED_MATRIX_ENABLE = pins
+RGBLIGHT_ENABLE = no
+AUDIO_ENABLE = yes

keyboards/crkbd/keymaps/tominabox1/keymap.c

@@ -0,0 +1,46 @@
+#include QMK_KEYBOARD_H
+#include "tominabox1.h"
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  [_BASE] = LAYOUT_wrapper(
+    ___________________CRKBD1__________________,
+    ___________________CRKBD2__________________,
+    ___________________CRKBD3__________________,
+    ___________________CRKBD4__________________
+  ),
+
+  [_RAISE] = LAYOUT_wrapper(
+    ___________________RAISE1__________________,
+    ___________________RAISE2__________________,
+    ___________________CRKBD_RAISE3____________,
+    ___________________CRKBD_RAISE4____________
+  ),
+
+  [_LOWER] = LAYOUT_wrapper(
+    _________________LOWER_1___________________,
+    _________________LOWER_2___________________,
+    ___________________CRKBD_LOW3______________,
+    ___________________CRKBD_LOW4______________
+  ),
+
+  [_ADJUST] = LAYOUT_wrapper(
+    ___________________ADJST1__________________,
+    ___________________CRKBD_ADJST2____________,
+    ___________________CRKBD_ADJST3____________,
+    ___________________CRKBD_ADJST4____________
+  ),
+
+  [_ARROW] = LAYOUT_wrapper(
+    ___________________ARROW1__________________,
+    ___________________ARROW2__________________,
+    ___________________ARROW3__________________,
+    ___________________ARROW4__________________
+   ),
+   [_FKEY] = LAYOUT_wrapper(
+    ___________________FKEY1___________________,
+    ___________________FKEY2___________________,
+    ___________________CRKBD_FKEY3_____________,
+    ___________________CRKBD_FKEY4_____________
+  )
+
+};

keyboards/dz60/keymaps/pok3r/keymap.c

@@ -0,0 +1,25 @@
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+	LAYOUT(
+		KC_GESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_NO, KC_BSPC,
+		KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS,
+		MO(1), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT,
+		KC_LSFT, KC_NO, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_NO,
+		KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_SPC, KC_SPC, KC_RALT, MO(1), KC_NO, MO(2), KC_RCTL),
+
+	LAYOUT(
+		KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, _______, KC_DEL,
+		_______, KC_MPRV, KC_MPLY, KC_MNXT, RESET, _______, KC_CALC, KC_PGUP, KC_UP, KC_PGDN, KC_PSCR, KC_SLCK, KC_PAUS, _______,
+		KC_CAPS, _______, KC_VOLD, KC_VOLU, KC_MUTE, _______, KC_HOME, KC_LEFT, KC_DOWN, KC_RGHT, KC_INS, KC_DEL, _______,
+		_______, KC_APP, _______, _______, _______, _______, KC_END, _______, _______, _______, _______, _______, _______, _______,
+		_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______),
+
+	LAYOUT(
+		RGB_TOG, RGB_M_P, RGB_M_B, RGB_M_R, RGB_M_SW, RGB_M_SN, RGB_M_K, RGB_M_X, RGB_M_G, RGB_M_T, _______, RGB_RMOD, RGB_MOD, _______, _______,
+		_______, RGB_HUI, RGB_SAI, RGB_VAI, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+		_______, RGB_HUD, RGB_SAD, RGB_VAD, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+		_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+		_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______),
+};

keyboards/dztech/dz65rgb/keymaps/catrielmuller/config.h

@@ -0,0 +1,3 @@
+#define LEADER_TIMEOUT 300
+#define FORCE_NKRO
+#define UNICODE_SELECTED_MODES UC_LNX, UC_OSX, UC_WIN, UC_WINC

keyboards/dztech/dz65rgb/keymaps/catrielmuller/keymap.c

@@ -0,0 +1,242 @@
+#include QMK_KEYBOARD_H
+
+// Config
+const uint8_t MAIN_COLOR[3] = {0xFF, 0x00, 0x00};
+
+// layers, ordering is important!
+enum layers {
+    _MAIN,
+    _INDEX,
+    _FN,
+    _MULTIMEDIA,
+    _EMOJI,
+    _EXT1,
+    _EXT2,
+    _EXT3,
+    _EXT4,
+    _EXT5,
+    _EXT6,
+    _RGB,
+    _CONFIG,
+}
+
+const layers_leds_map[] = {
+    [_MAIN] = 17,
+    [_INDEX] = 16,
+    [_FN] = 15,
+    [_MULTIMEDIA] = 14,
+    [_EMOJI] = 13,
+    [_EXT1] = 12,
+    [_EXT2] = 11,
+    [_EXT3] = 10,
+    [_EXT4] = 9,
+    [_EXT5] = 18,
+    [_EXT6] = 19,
+    [_RGB] = 20,
+    [_CONFIG] = 21,
+};
+
+enum unicode_names {
+    UC_GRINNING_FACE, // 😃
+    UC_BEAMING_FACE, // 😁
+    UC_GRINNING_FACE_WITH_SWEAT, // 😅
+    UC_ROLLING_LAUGHING, // 🤣
+    UC_FACE_TEARS_JOY, // 😂
+    UC_WINKING_FACE, // 😉
+    UC_SMILING_FACE_HALO, // 😇
+    UC_SMILING_FACE_HEARTS, // 🥰
+    UC_SMILING_FACE_HEART_EYES, // 😍
+    UC_FACE_BLOWING_KISS, // 😘
+    UC_FACE_SAVORING_FOOD, // 😋
+    UC_ZANY_FACE, // 🤪
+    UC_HUGGING_FACE, // 🤗
+    UC_SHUSHING_FACE, // 🤫
+    UC_THINKING_FACE, // 🤔
+    UC_FACE_RAISED_EYEBROW, // 🤨
+    UC_NEUTRAL_FACE, // 😐
+    UC_SMIRKING_FACE, // 😏
+    UC_FACE_ROLLING_EYES, // 🙄
+    UC_PENSIVE_FACE, // 😔
+    UC_FACE_VOMITING, // 🤮
+    UC_WOOZY_FACE, // 🥴
+    UC_PLEADING_FACE, // 🥺
+    UC_LOUDLY_CRYING_FACE, // 😭
+    UC_DISAPPOINTED_FACE, // 😞
+    UC_FACE_SYMBOLS_MOUTH, // 🤬
+    UC_SMILING_FACE_HORNS, // 😈
+    UC_SKULL, // 💀
+    UC_PILE_POO, // 💩
+    UC_GHOST, // 👻
+    UC_ALIEN_MONSTER, // 👾
+    UC_RED_HEART, // ❤
+    UC_BOMB, // 💣
+    UC_WAVING_HAND, // 👋
+    UC_OK_HAND, // 👌
+    UC_CLAPPING_HANDS, // 👏
+    UC_EYES, // 👀
+    UC_MAN_FACEPALMING, // 🤦
+    UC_TURTLE, // 🐢
+    UC_SNAKE, // 🐍
+    UC_SPOUTING_WHALE, // 🐳
+    UC_DRAGON, // 🐉
+    UC_TREX, // 🦖
+    UC_ARGENTINA_A, // 🇦
+    UC_ARGENTINA_R, // 🇷
+    UC_THUMBSDOWN, // 👍
+    UC_THUMBSUP, // 👎
+};
+
+const uint32_t PROGMEM unicode_map[] = {
+    [UC_GRINNING_FACE] = 0x1F603,
+    [UC_BEAMING_FACE] = 0x1F601,
+    [UC_GRINNING_FACE_WITH_SWEAT] = 0x1F605,
+    [UC_ROLLING_LAUGHING] = 0x1F923,
+    [UC_FACE_TEARS_JOY] = 0x1F602,
+    [UC_WINKING_FACE] = 0x1F609,
+    [UC_SMILING_FACE_HALO] = 0x1F607,
+    [UC_SMILING_FACE_HEARTS] = 0x1F970,
+    [UC_SMILING_FACE_HEART_EYES] = 0x1F60D,
+    [UC_FACE_BLOWING_KISS] = 0x1F618,
+    [UC_FACE_SAVORING_FOOD] = 0x1F60B,
+    [UC_ZANY_FACE] = 0x1F92A,
+    [UC_HUGGING_FACE] = 0x1F917,
+    [UC_SHUSHING_FACE] = 0x1F92B,
+    [UC_THINKING_FACE] = 0x1F914,
+    [UC_FACE_RAISED_EYEBROW] = 0x1F928,
+    [UC_NEUTRAL_FACE] = 0x1F610,
+    [UC_SMIRKING_FACE] = 0x1F60F,
+    [UC_FACE_ROLLING_EYES] = 0x1F644,
+    [UC_PENSIVE_FACE] = 0x1F614,
+    [UC_FACE_VOMITING] = 0x1F92E,
+    [UC_WOOZY_FACE] = 0x1F974,
+    [UC_PLEADING_FACE] = 0x1F97A,
+    [UC_LOUDLY_CRYING_FACE] = 0x1F62D,
+    [UC_DISAPPOINTED_FACE] = 0x1F61E,
+    [UC_FACE_SYMBOLS_MOUTH] = 0x1F92C,
+    [UC_SMILING_FACE_HORNS] = 0x1F608,
+    [UC_SKULL] = 0x1F480,
+    [UC_PILE_POO] = 0x1F4A9,
+    [UC_GHOST] = 0x1F47B,
+    [UC_ALIEN_MONSTER] = 0x1F47E,
+    [UC_RED_HEART] = 0x2764,
+    [UC_BOMB] = 0x1F4A3,
+    [UC_WAVING_HAND] = 0x1F44B,
+    [UC_OK_HAND] = 0x1F44C,
+    [UC_CLAPPING_HANDS] = 0x1F44F,
+    [UC_EYES] = 0x1F440,
+    [UC_MAN_FACEPALMING] = 0x1F926,
+    [UC_TURTLE] = 0x1F422,
+    [UC_SNAKE] = 0x1F40D,
+    [UC_SPOUTING_WHALE] = 0x1F433,
+    [UC_DRAGON] = 0x1F409,
+    [UC_TREX] = 0x1F996,
+    [UC_ARGENTINA_A] = 0x1F1E6,
+    [UC_ARGENTINA_R] = 0x1F1F7,
+    [UC_THUMBSDOWN] = 0x1F44E,
+    [UC_THUMBSUP] = 0x1F44D,
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+    [_MAIN] = LAYOUT_65_ansi(
+        KC_GESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, KC_HOME,
+        KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, KC_END,
+        KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, KC_PGUP,
+        KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, RSFT_T(KC_APP), KC_UP, KC_PGDN,
+        KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_LEAD, TO(_INDEX), MO(_FN), KC_LEFT, KC_DOWN, KC_RGHT
+    ),
+    [_INDEX] = LAYOUT_65_ansi(
+        TO(_MAIN), TO(_INDEX), TO(_FN), TO(_MULTIMEDIA), TO(_EMOJI), TO(_EXT1), TO(_EXT2), TO(_EXT3), TO(_EXT4), TO(_EXT5), TO(_EXT6), TO(_RGB), TO(_CONFIG), TO(_MAIN), KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, TO(_INDEX), TO(_FN), KC_NO, KC_NO, KC_NO
+    ),
+    [_FN] = LAYOUT_65_ansi(
+        KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_DEL, KC_PSCR,
+        KC_TAB, KC_F13, KC_F14, KC_F15, KC_F16, KC_F17, KC_F18, KC_F19, KC_F20, KC_F21, KC_F22, KC_F23, KC_F24, KC_INS, KC_SLCK,
+        KC_APP, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_PAUS,
+        KC_LSFT, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_BTN1, KC_MS_U, KC_BTN2,
+        KC_LCTL, KC_LGUI, KC_LALT, KC_NO, KC_NO, TO(_INDEX), KC_TRNS, KC_MS_L, KC_MS_D, KC_MS_R
+    ),
+    [_MULTIMEDIA] = LAYOUT_65_ansi(
+        TO(_MAIN), KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_MPLY, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_MSTP, KC_VOLU, KC_MUTE,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, TO(_INDEX), KC_NO, KC_MPRV, KC_VOLD, KC_MNXT
+    ),
+    [_EMOJI] = LAYOUT_65_ansi(
+        TO(_MAIN), X(UC_GRINNING_FACE), X(UC_BEAMING_FACE), X(UC_GRINNING_FACE_WITH_SWEAT), X(UC_ROLLING_LAUGHING), X(UC_FACE_TEARS_JOY), X(UC_WINKING_FACE), X(UC_SMILING_FACE_HALO), X(UC_SMILING_FACE_HEARTS), X(UC_SMILING_FACE_HEART_EYES), X(UC_FACE_BLOWING_KISS), X(UC_FACE_SAVORING_FOOD), X(UC_ZANY_FACE), KC_BSPC, KC_HOME,
+        KC_TAB, X(UC_HUGGING_FACE), X(UC_SHUSHING_FACE), X(UC_THINKING_FACE), X(UC_FACE_RAISED_EYEBROW), X(UC_NEUTRAL_FACE), X(UC_SMIRKING_FACE), X(UC_FACE_ROLLING_EYES), X(UC_PENSIVE_FACE), X(UC_FACE_VOMITING), X(UC_WOOZY_FACE), X(UC_PLEADING_FACE), X(UC_LOUDLY_CRYING_FACE), X(UC_THUMBSUP), KC_END,
+        KC_APP, X(UC_DISAPPOINTED_FACE), X(UC_FACE_SYMBOLS_MOUTH), X(UC_SMILING_FACE_HORNS), X(UC_SKULL), X(UC_PILE_POO), X(UC_GHOST), X(UC_ALIEN_MONSTER), X(UC_RED_HEART), X(UC_BOMB), X(UC_WAVING_HAND), X(UC_OK_HAND), KC_ENT, KC_PGUP,
+        KC_LSFT, X(UC_CLAPPING_HANDS), X(UC_EYES), X(UC_MAN_FACEPALMING), X(UC_TURTLE), X(UC_SNAKE), X(UC_SPOUTING_WHALE), X(UC_DRAGON), X(UC_TREX), X(UC_ARGENTINA_A), X(UC_ARGENTINA_R), X(UC_THUMBSDOWN), KC_UP, KC_PGDN,
+        KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_LEAD, TO(_INDEX), TO(_MAIN), KC_LEFT, KC_DOWN, KC_RGHT
+    ),
+    [_EXT1] = LAYOUT_65_ansi(
+        TO(_MAIN), KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, TO(_INDEX), KC_NO, KC_NO, KC_NO, KC_NO
+    ),
+    [_EXT2] = LAYOUT_65_ansi(
+        TO(_MAIN), KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, TO(_INDEX), KC_NO, KC_NO, KC_NO, KC_NO
+    ),
+    [_EXT3] = LAYOUT_65_ansi(
+        TO(_MAIN), KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, TO(_INDEX), KC_NO, KC_NO, KC_NO, KC_NO
+    ),
+    [_EXT4] = LAYOUT_65_ansi(
+        TO(_MAIN), KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, TO(_INDEX), KC_NO, KC_NO, KC_NO, KC_NO
+    ),
+    [_EXT5] = LAYOUT_65_ansi(
+        TO(_MAIN), KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, TO(_INDEX), KC_NO, KC_NO, KC_NO, KC_NO
+    ),
+    [_EXT6] = LAYOUT_65_ansi(
+        TO(_MAIN), KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, TO(_INDEX), KC_NO, KC_NO, KC_NO, KC_NO
+    ),
+    [_RGB] = LAYOUT_65_ansi(
+        TO(_MAIN), KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, RGB_TOG, RGB_RMOD, RGB_MOD, RGB_HUD, RGB_HUI, RGB_SAD, RGB_SAI, RGB_VAD, RGB_VAI, RGB_SPD, RGB_SPI, KC_NO, KC_NO, KC_NO,
+        KC_NO, RGB_M_P, RGB_M_B, RGB_M_R, RGB_M_SW, RGB_M_SN, RGB_M_K, RGB_M_X, RGB_M_G, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, TO(_INDEX), KC_NO, KC_NO, KC_NO, KC_NO
+    ),
+    [_CONFIG] = LAYOUT_65_ansi(
+        TO(_MAIN), KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_ACL2,
+        KC_NO, KC_PWR, KC_SLEP, KC_WAKE, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, RESET, DEBUG, EEP_RST, KC_NO, KC_ACL1,
+        KC_NO, UC_RMOD, UC_MOD, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_ACL0,
+        KC_NO, MAGIC_TOGGLE_NKRO, MAGIC_UNHOST_NKRO, MAGIC_HOST_NKRO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,
+        KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, TO(_INDEX), KC_NO, KC_NO, KC_NO, KC_NO
+    ),
+};
+
+void rgb_matrix_indicators_user(void) {
+
+    // CapsLock Light
+    if (IS_HOST_LED_ON(USB_LED_CAPS_LOCK)) {
+        rgb_matrix_set_color(8, MAIN_COLOR[0], MAIN_COLOR[1], MAIN_COLOR[2]);
+    }
+
+    // Show Selected Layer
+    rgb_matrix_set_color(layers_leds_map[biton32(layer_state)], MAIN_COLOR[0], MAIN_COLOR[1], MAIN_COLOR[2]);
+}

keyboards/dztech/dz65rgb/keymaps/catrielmuller/rules.mk

@@ -0,0 +1,2 @@
+LEADER_ENABLE = yes
+UNICODEMAP_ENABLE = yes

keyboards/ergodash/rev1/keymaps/yet-another-developer/config.h

@@ -0,0 +1,67 @@
+/*
+This is the c configuration file for the keymap
+
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+Copyright 2015 Jack Humbert
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+
+/* Use I2C or Serial, not both */
+#define USE_SERIAL
+// #define USE_I2C
+
+/* Select hand configuration */
+
+//#define MASTER_LEFT
+#define MASTER_RIGHT /* Cable connected to the right split keyboard */
+// #define EE_HANDS
+
+#define AUTO_SHIFT_TIMEOUT 210
+
+#define TAPPING_TERM_PER_KEY
+
+// https://beta.docs.qmk.fm/features/feature_leader_key
+//#define LEADER_PER_KEY_TIMING
+//#define LEADER_TIMEOUT 280
+
+// https://docs.qmk.fm/#/feature_mouse_keys
+#define MK_3_SPEED // Constant Speed Mode
+
+#define MOUSEKEY_DELAY 300
+#define MOUSEKEY_INTERVAL 16
+#define MOUSEKEY_MAX_SPEED 3
+#define MOUSEKEY_TIME_TO_MAX 60
+#define MK_C_OFFSET_0    4
+#define MK_C_INTERVAL_0  28
+#define MK_C_OFFSET_1    8
+#define MK_C_INTERVAL_1  16
+#define MK_C_OFFSET_2    20
+#define MK_C_INTERVAL_2  16
+
+#define MOUSEKEY_WHEEL_MAX_SPEED 4
+#define MOUSEKEY_WHEEL_TIME_TO_MAX 40
+
+#define MK_W_OFFSET_0       1
+#define MK_W_INTERVAL_0     120
+#define MK_W_OFFSET_1       1
+#define MK_W_INTERVAL_1     100
+#define MK_W_OFFSET_2       1
+#define MK_W_INTERVAL_2     60
+
+//#define STARTUP_RESET_EEPROM // EMERGENCY
+

keyboards/ergodash/rev1/keymaps/yet-another-developer/keymap.c

@@ -0,0 +1,157 @@
+#include QMK_KEYBOARD_H
+#include "yet-another-developer.h"
+
+#ifndef UNICODE_ENABLE
+#    define UC(x) KC_NO
+#endif
+
+extern keymap_config_t keymap_config;
+
+#define EISU LALT(KC_GRV)
+
+#define LAYOUT_ergodash_pretty_wrapper(...)   LAYOUT_ergodash_pretty(__VA_ARGS__)
+
+    /* Keymap: BASE layer
+     *
+     * ,----------------------------------------------------.           ,----------------------------------------------------.
+     * | ESC    |   1    |   2  |   3  |   4  |   5  |   [  |           |  ]   |   6  |   7  |   8  |   9  |   0    | Pscree |
+     * |--------+--------+------+------+------+-------------|           |------+------+------+------+------+--------+--------|
+     * | `      |   K01  |  K02 |  K03 |  K04 |  K05 |   -  |           |  =   |  K06 |  K07 |  K08 |  K09 |  K0A   |   \    |
+     * |--------+--------+------+------+------+------|------|           |------|------+------+------+------+--------+--------|
+     * | Tab    |   K11  |  K12 |  K13 |  K14 |  K15 |   {  |           |  }   |  K16 |  K17 |  K18 |  K19 |  K1A   |   "    |
+     * |--------+--------+------+------+------+------|------'           `------|------+------+------+------+--------+--------|
+     * | LShift |   K21  |  K22 |  K23 |  K24 |  K25 |                         |  K26 |  K27 |  K28 |  K29 |  K2A   | RShift |
+     * |--------+--------+------+------+------+------'                         `------+------+------+------+--------+--------|
+     * | LCtrl  |   GUI  |  Alt |  Alt |                                                     | LEFT | DOWN |   UP   | RIGHT  |
+     * `-------------------------------'                                                     `-------------------------------'
+     *                                       ,--------------.           ,--------------.
+     *                                       | Lower|       |           |      | Raise |
+     *                               ,-------|   /  |  Del  |           | Bksp +   /   +-------.
+     *                               |CMD/Spc| Space|       |           |      | Enter |CMD/Spc|
+     *                               `----------------------'           `----------------------'
+     */
+#define LAYOUT_ergodash_pretty_base( \
+    K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, \
+    K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, \
+    K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A  \
+  ) \
+  LAYOUT_ergodash_pretty_wrapper( \
+      KC_ESC,  ________________NUMBER_LEFT________________, KC_LBRC,                  KC_RBRC, ________________NUMBER_RIGHT_______________, KC_PSCR, \
+      KC_GRV,  K01,     K02,     K03,     K04,     K05,     KC_MINS,                  KC_EQL,  K06,    K07,    K08,    K09,    K0A,         KC_BSLS, \
+      KC_TAB,  K11,     K12,     K13,     K14,     K15,     KC_LCBR,                  KC_RCBR, K16,    K17,    K18,    K19,    K1A,         KC_QUOT, \
+      OS_LSFT, K21,     K22,     K23,     K24,     K25,                                        K26,    K27,    K28,    K29,    K2A,         OS_RSFT, \
+      KC_LCTL, KC_LGUI, KC_LALT, KC_LALT,                                                                    KC_LEFT, KC_DOWN, KC_UP,       KC_RIGHT, \
+                                              LT(_LOWER, KC_SPC),                         LT(_RAISE, KC_ENT),                                        \
+                                      OS_LGUI,LT(_LOWER, KC_SPC),KC_DEL,         KC_BSPC, LT(_RAISE, KC_ENT),  OS_RGUI                               \
+    )
+
+#define LAYOUT_ergodash_pretty_base_wrapper(...)       LAYOUT_ergodash_pretty_base(__VA_ARGS__)
+
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+  [_QWERTY] = LAYOUT_ergodash_pretty_base_wrapper(
+    _________________QWERTY_L1_________________, _________________QWERTY_R1_________________,
+    _________________QWERTY_L2_________________, _________________QWERTY_R2_________________,
+    _________________QWERTY_L3_________________, _________________QWERTY_R3_________________
+  ),
+
+/* Keymap: COLEMAK layer
+ *
+ * ,----------------------------------------------------.           ,----------------------------------------------------.
+ * | ESC    |   1    |   2  |   3  |   4  |   5  |   [  |           |  ]   |   6  |   7  |   8  |   9  |   0    |   -    |
+ * |--------+--------+------+------+------+-------------|           |------+------+------+------+------+--------+--------|
+ * | `      |    Q   |   W  |   F  |   P  |   G  |   -  |           |  =   |   J  |   L  |   U  |   Y  |   ;    |   \    |
+ * |--------+--------+------+------+------+------|------|           |------|------+------+------+------+--------+--------|
+ * | Tab    |    A   |   R  |   S  |   T  |   D  |  Del |           | Bksp |   H  |   N  |   E  |   I  |   O    |   '    |
+ * |--------+--------+------+------+------+------|------'           `------|------+------+------+------+--------+--------|
+ * | LShift |    Z   |   X  |   C  |   V  |   B  |                         |   K  |   M  |  , < |  . > |   /    | RShift |
+ * |--------+--------+------+------+------+------'                         `------+------+------+------+--------+--------|
+ * | Ctrl   |   GUI  |  Alt | EISU |                                                     | LEFT | DOWN |   UP   | RIGHT  |
+ * `-------------------------------'                                                     `-------------------------------'
+ *                                       ,--------------.           ,--------------.
+ *                                       | Lower|       |           |      | Raise |
+ *                               ,-------|   /  |  Del  |           | Bksp +   /   +-------.
+ *                               |CMD/Spc| Space|       |           |      | Enter |CMD/Spc|
+ *                               `----------------------'           `----------------------'
+ */
+
+
+// If it accepts an argument (i.e, is a function), it doesn't need KC_.
+// Otherwise, it needs KC_*
+  [_COLEMAK] = LAYOUT_ergodash_pretty_base_wrapper(
+    _________________COLEMAK_L1________________, _________________COLEMAK_R1________________,
+    _________________COLEMAK_L2________________, _________________COLEMAK_R2________________,
+    _________________COLEMAK_L3________________, _________________COLEMAK_R3________________
+  ),
+
+  [_DVORAK] = LAYOUT_ergodash_pretty_base_wrapper(
+    _________________DVORAK_L1_________________, _________________DVORAK_R1_________________,
+    _________________DVORAK_L2_________________, _________________DVORAK_R2_________________,
+    _________________DVORAK_L3_________________, _________________DVORAK_R3_________________
+  ),
+
+  [_WORKMAN] = LAYOUT_ergodash_pretty_base_wrapper(
+    _________________WORKMAN_L1________________, _________________WORKMAN_R1________________,
+    _________________WORKMAN_L2________________, _________________WORKMAN_R2________________,
+    _________________WORKMAN_L3________________, _________________WORKMAN_R3________________
+  ),
+
+#ifdef UNICODEMAP_ENABLE
+  [_UNICODE] = LAYOUT_ergodash_pretty_base_wrapper(
+    _______________UNICODE_L1__________________, _______________UNICODE_R1__________________,
+    _______________UNICODE_L2__________________, _______________UNICODE_R2__________________,
+    _______________UNICODE_L3__________________, _______________UNICODE_R3__________________
+  ),
+#endif
+
+  [_LOWER] = LAYOUT_ergodash_pretty_wrapper(
+    KC_F11,  _________________FUNC_LEFT_________________, KC_RST ,         KC_RST , _________________FUNC_RIGHT________________, KC_F12,
+    KC_TILD, _________________LOWER_L1__________________, _______,         _______, _________________LOWER_R1__________________, KC_PIPE,
+    _______, _________________LOWER_L2__________________, _______,         _______, _________________LOWER_R2__________________, KC_DQUO,
+    _______, _________________LOWER_L3__________________,                           _________________LOWER_R3__________________, KC_PSCR,
+    _______, _______, _______, _______,                                                               _______, _______, _______, KC_PAUS,
+                                                _______,                            _______,
+                                        _______, _______, _______,         _______, _______, _______
+    ),
+
+  [_RAISE] = LAYOUT_ergodash_pretty_wrapper(
+    KC_F12,  _________________FUNC_LEFT_________________, KC_RST,          KC_RST , _________________FUNC_RIGHT________________, KC_F11,
+    KC_GRV,  _________________RAISE_L1__________________, _______,         _______, _________________RAISE_R1__________________, KC_BSLS,
+    _______, _________________RAISE_L2__________________, _______,         _______, _________________RAISE_R2__________________, KC_QUOT,
+    _______, _________________RAISE_L3__________________,                           _________________RAISE_R3__________________, KC_PSCR,
+    _______, _______, _______, _______,                                                               KC_HOME, KC_PGDN, KC_PGUP, KC_END,
+                                                 _______,                           _______,
+                                        _______, _______, _______,         _______, _______, _______
+    ),
+
+  [_ADJUST] = LAYOUT_ergodash_pretty_wrapper(
+    KC_MAKE, _______, _______, _______, _______, _______, _______,         KC_NUKE, _______, _______, _______, _______, _______, KC_RST,
+    VRSN,    _________________ADJUST_L1_________________, _______,         _______, _________________ADJUST_R1_________________, EEP_RST,
+    _______, _________________ADJUST_L2_________________, _______,         _______, _________________ADJUST_R2_________________, _______,
+    _______, _________________ADJUST_L3_________________,                           _________________ADJUST_R3_________________, _______,
+    _______, _______, _______, _______,                                                               _______, _______, _______, _______,
+                                                 _______,                           _______,
+                                        _______, _______, _______,         _______, _______, _______
+    ),
+};
+
+#ifdef AUDIO_ENABLE
+float tone_qwerty[][2]     = SONG(QWERTY_SOUND);
+#endif
+
+void persistent_default_layer_set(uint16_t default_layer) {
+  eeconfig_update_default_layer(default_layer);
+  default_layer_set(default_layer);
+}
+
+bool process_record_keymap(uint16_t keycode, keyrecord_t *record) {
+    return true;
+}
+void matrix_init_keymap(void) {
+#ifdef STARTUP_RESET_EEPROM
+    eeconfig_init();
+#endif
+}
+
+//

keyboards/ergodash/rev1/keymaps/yet-another-developer/rules.mk

@@ -0,0 +1,23 @@
+BOOTMAGIC_ENABLE  = no       # Virtual DIP switch configuration(+1000)
+
+# Device
+AUDIO_ENABLE 	  = no
+
+RGBLIGHT_ENABLE   = no
+BACKLIGHT_ENABLE  = no
+INDICATOR_LIGHTS  = no
+
+# QMK Features
+AUTO_SHIFT_ENABLE = no
+MOUSEKEY_ENABLE   = no
+CONSOLE_ENABLE    = no       # Console for debug(+400)
+COMMAND_ENABLE    = no       # Commands for debug and configuration
+LEADER_ENABLE     = yes      # default is yes
+TAP_DANCE_ENABLE  = no       #(+1254)
+UNICODE_ENABLE    = no       #(+1134)
+UNICODEMAP_ENABLE = no
+NKRO_ENABLE       = no
+MACROS_ENABLED    = no
+
+# User Defined Features
+NO_SECRETS        = no

keyboards/ergodox_ez/keymaps/rishka/config.h

@@ -0,0 +1,17 @@
+#pragma once
+
+#define PERMISSIVE_HOLD
+
+#undef MOUSEKEY_TIME_TO_MAX
+#define MOUSEKEY_TIME_TO_MAX    0
+
+#undef MOUSEKEY_WHEEL_MAX_SPEED
+#undef MOUSEKEY_WHEEL_TIME_TO_MAX
+
+#define MOUSEKEY_WHEEL_MAX_SPEED    1
+#define MOUSEKEY_WHEEL_TIME_TO_MAX  0
+
+#define MK_C_OFFSET_1 20
+#define MK_C_OFFSET_2 30
+
+#undef MK_MOMENTARY_ACCEL

keyboards/ergodox_ez/keymaps/rishka/keymap.c

@@ -0,0 +1,210 @@
+
+#include QMK_KEYBOARD_H
+#include "version.h"
+#include "rishka.h"
+enum layers {
+  BASE, // default layer
+  WIN, // Switch keys that are needed in windows
+  SYMB, // symbols
+  MDIA, // media keys
+  GAME, // Gamepad setup
+  FIRMWARE // Layer to trigger reset/refresh
+};
+enum custom_keycodes {
+  VRSN = SAFE_RANGE,
+  RGB_SLD
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+[BASE] = LAYOUT_ergodox_pretty_wrapper(
+  KC_EQL,  ________________NUMBERS_L__________________, TG(WIN),       OSX_LOCK, ________________NUMBERS_R__________________, KC_MINS,
+  KC_DELT, _________________QWERTY_L1_________________, TG(SYMB),      TG(SYMB), _________________QWERTY_R1_________________, KC_BSLS,
+  KC_BSPC, _____________MOD_QWERTY_L2_________________,                          _____________MOD_QWERTY_R2_________________, LT(MDIA, KC_QUOT),
+  OS_LSFT, _________________QWERTY_L3_________________, ALL_T(KC_NO),  TG(MDIA), _________________QWERTY_R3_________________, OS_RSFT,
+  LT(SYMB,KC_GRV), KC_QUOT, LALT(KC_LSFT), KC_LEFT, KC_RGHT,                        KC_UP,   KC_DOWN, KC_LBRC,  KC_RBRC,        OSL(SYMB),
+                                           ALT_T(KC_APP), TG(GAME),       KC_LALT,         CTL_T(KC_ESC),
+                                            LT(FIRMWARE, KC_HOME),        KC_PGUP,
+                            KC_SPC, GUI_T(KC_BSPC), ALT_T(KC_END),        GUI_T(KC_PGDN),  CTL_T(KC_TAB), ALT_T(KC_ENT)
+),
+
+[WIN] = LAYOUT_ergodox_pretty_wrapper(
+  _______, _______, _______, _______, _______, _______, _______,     _______, _______, _______, _______, _______, _______, _______,
+  KC_F1,   _______, _______, _______, _______, _______, _______,     _______, _______, _______, _______, _______, _______, _______,
+  KC_TAB,  _________________QWERTY_L2_________________,                       _______, _______, _______, _______, _______, _______,
+  _______, _______,    _______, _______, _______, _______, KC_LGUI,  _______, _______, _______, _______, _______, _______, _______,
+  KC_LCTL, _______, KC_LALT, _______, _______,                                         _______, _______, _______, _______, _______,
+                                               _______, KC_ESC,      _______, _______,
+                                                        _______,     _______,
+                                      _______, KC_BSPC, KC_LALT,     KC_PGDN, CTL_T(KC_TAB), _______
+),
+
+[SYMB] = LAYOUT_ergodox_pretty_wrapper(
+VRSN,    ______________________F_L__________________, KC_F11,       KC_F12 , ______________________F_R__________________, KC_NLCK,
+_______, _________________SYMBOL_L1_________________, _______,      _______, _________________SYMBOL_R1_________________, _______,
+_______, _________________SYMBOL_L2_________________,                        _________________SYMBOL_R2_________________, _______,
+_______, _________________SYMBOL_L3_________________, _______,      _______, _________________SYMBOL_R3_________________, _______,
+_______, _______, _______, _______, _______,                                          _______, KC_P0, KC_PDOT, KC_PSLS, _______,
+                                               RGB_MOD, RGB_VAI,   RGB_HUI, RGB_SLD,
+                                                        RGB_VAD,   RGB_HUD,
+                                      _______, _______, _______,   RGB_TOG, _______, _______
+),
+
+[MDIA] = LAYOUT_ergodox(
+  // left hand
+  _______, _______, _______, _______, _______, _______, _______,
+  _______, _______, _______, KC_MS_U, _______, KC_WH_U, _______,
+  _______, _______, KC_MS_L, KC_MS_D, KC_MS_R, KC_WH_D,
+  _______, _______, _______, _______, _______, _______, _______,
+  _______, _______, _______, KC_BTN1, KC_BTN2,
+                                               _______, KC_BTN5,
+                                                        KC_BTN4,
+                                      KC_BTN1, KC_BTN2, KC_BTN3,
+  // right hand
+  _______, _______, _______, _______, _______, _______, _______,
+  _______, _______, _______, KC_WH_U, _______, _______, _______,
+           _______, KC_WH_L, KC_WH_D, KC_WH_R, _______, KC_MPLY,
+  _______, _______, _______, KC_MPRV, KC_MNXT, _______, _______,
+                    KC_VOLU, KC_VOLD, KC_MUTE, _______, _______,
+  _______, _______,
+  _______,
+  KC_ACL2, KC_ACL1, KC_ACL0
+),
+
+[GAME] = LAYOUT_ergodox(
+  // left hand
+  KC_ESCAPE, KC_GRAVE, KC_1, KC_2, KC_3, KC_4, KC_5,
+  KC_F1, KC_Y, KC_Q, KC_W, KC_E, KC_R, KC_T,
+  KC_TAB, KC_LSHIFT, KC_A, KC_S, KC_D, KC_F,
+  KC_LCTRL, KC_B, KC_Z, KC_X, KC_C, KC_V, KC_G,
+  LT(BASE, KC_L), KC_J, KC_I, KC_O, KC_M,
+                                               KC_ESCAPE, _______,
+                                                        KC_ENTER,
+                                      KC_SPACE, KC_LCTRL, KC_LALT,
+ // right hand
+  KC_RGHT,      KC_6,    KC_7,    KC_8,    KC_9,              KC_0,           KC_MINS,
+  TG(SYMB),     KC_Y,    KC_U,    KC_I,    KC_O,              KC_P,           KC_BSLS,
+  KC_H,         KC_J,    KC_K,    KC_L,    LT(MDIA, KC_SCLN), GUI_T(KC_QUOT),
+  MEH_T(KC_NO), KC_N,    KC_M,    KC_COMM, KC_DOT,            CTL_T(KC_SLSH), KC_RSFT,
+  KC_UP,        KC_DOWN, KC_LBRC, KC_RBRC, TT(SYMB),
+  KC_LALT, CTL_T(KC_ESC),
+  KC_PGUP,
+  KC_PGDN, KC_TAB, KC_ENT
+),
+
+[FIRMWARE] = LAYOUT_ergodox(
+  // left hand
+  _______, _______, _______, _______, _______, _______, _______,
+  _______, _______, _______, _______, _______, _______, _______,
+  _______, _______, _______, _______, _______, _______,
+  _______, _______, _______, _______, _______, _______, _______,
+  _______, _______, _______, _______, _______,
+                                               _______, _______,
+                                                        _______,
+                                      RESET, _______, _______,
+  // right hand
+  _______, _______, _______, _______, _______, _______, _______,
+  _______, _______, _______, _______, _______, _______, _______,
+           _______, _______, _______, _______, _______, _______,
+  _______, _______, _______, _______, _______, _______, _______,
+                    _______, _______, _______, _______, _______,
+  _______, _______,
+  _______,
+  _______, _______, EEP_RST
+),
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  if (record->event.pressed) {
+    switch (keycode) {
+      case VRSN:
+        SEND_STRING (QMK_KEYBOARD "/" QMK_KEYMAP " @ " QMK_VERSION);
+        return false;
+      #ifdef RGBLIGHT_ENABLE
+      case RGB_SLD:
+        rgblight_mode(1);
+        return false;
+      #endif
+    }
+  }
+  return true;
+}
+
+// Runs just one time when the keyboard initializes.
+void keyboard_post_init_user(void) {
+#ifdef RGBLIGHT_COLOR_LAYER_0
+  rgblight_setrgb(RGBLIGHT_COLOR_LAYER_0);
+#endif
+};
+
+// Runs whenever there is a layer state change.
+uint32_t layer_state_set_user(layer_state_t state) {
+  ergodox_board_led_off();
+  ergodox_right_led_1_off();
+  ergodox_right_led_2_off();
+  ergodox_right_led_3_off();
+
+  uint8_t layer = get_highest_layer(state);
+  switch (layer) {
+      case 0:
+        #ifdef RGBLIGHT_COLOR_LAYER_0
+          rgblight_setrgb(RGBLIGHT_COLOR_LAYER_0);
+        #else
+        #ifdef RGBLIGHT_ENABLE
+          rgblight_init();
+        #endif
+        #endif
+        break;
+      case 1:
+        ergodox_right_led_1_on();
+        #ifdef RGBLIGHT_COLOR_LAYER_1
+          rgblight_setrgb(RGBLIGHT_COLOR_LAYER_1);
+        #endif
+        break;
+      case 2:
+        ergodox_right_led_2_on();
+        #ifdef RGBLIGHT_COLOR_LAYER_2
+          rgblight_setrgb(RGBLIGHT_COLOR_LAYER_2);
+        #endif
+        break;
+      case 3:
+        ergodox_right_led_3_on();
+        #ifdef RGBLIGHT_COLOR_LAYER_3
+          rgblight_setrgb(RGBLIGHT_COLOR_LAYER_3);
+        #endif
+        break;
+      case 4:
+        ergodox_right_led_1_on();
+        ergodox_right_led_2_on();
+        #ifdef RGBLIGHT_COLOR_LAYER_4
+          rgblight_setrgb(RGBLIGHT_COLOR_LAYER_4);
+        #endif
+        break;
+      case 5:
+        ergodox_right_led_1_on();
+        ergodox_right_led_3_on();
+        #ifdef RGBLIGHT_COLOR_LAYER_5
+          rgblight_setrgb(RGBLIGHT_COLOR_LAYER_5);
+        #endif
+        break;
+      case 6:
+        ergodox_right_led_2_on();
+        ergodox_right_led_3_on();
+        #ifdef RGBLIGHT_COLOR_LAYER_6
+          rgblight_setrgb(RGBLIGHT_COLOR_LAYER_6);
+        #endif
+        break;
+      case 7:
+        ergodox_right_led_1_on();
+        ergodox_right_led_2_on();
+        ergodox_right_led_3_on();
+        #ifdef RGBLIGHT_COLOR_LAYER_7
+          rgblight_setrgb(RGBLIGHT_COLOR_LAYER_7);
+        #endif
+        break;
+      default:
+        break;
+    }
+
+  return state;
+};

keyboards/ergodox_ez/keymaps/rishka/rules.mk

@@ -0,0 +1,2 @@
+# TAP_DANCE_ENABLE = yes
+MOUSEKEY_ENABLE = yes

keyboards/ergodox_infinity/keymaps/nordic_ergo/keymap.c

@@ -1,22 +1,18 @@
 // Nordic layout for Ergodox infinity
-
 #include QMK_KEYBOARD_H
-#include "debug.h"
-#include "action_layer.h"
 #include "version.h"
 #include "keymap_nordic.h"
 #include "keymap_german.h"
 
-// Layer names
-#define BASE 0 // default layer
-#define FUNCL 1 // function layer
-#define SYMB 2 // symbol layer
-#define MDIA 3 // media keys
+enum layer_names {
+    BASE,
+    FUNCL,
+    SYMB,
+    MDIA
+};
 
 enum custom_keycodes {
-    PLACEHOLDER = SAFE_RANGE, // can always be here
-    EPRM,
-    VRSN,
+    VRSN = SAFE_RANGE,
     RGB_SLD
 };
 
@@ -34,7 +30,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
  * |--------+------+------+------+------+------|  L2  |           |  L2  |------+------+------+------+------+--------|
  * | LShift |   Z  |   X  |   C  |   V  |   B  |      |           |      |   N  |   M  |   ,  |   .  |  -   | RShift |
  * `--------+------+------+------+------+-------------'           `-------------+------+------+------+------+--------'
- *   | Ctrl |  ¨^  |  <|>  | Alt | LGui|                                       | Ctrl |  Alt  |  ´`  |   +  | RGui |
+ *   | Ctrl |  ¨^  |  <|>  | LGui | Alt  |                                       | Ctrl |  Alt  |  ´`  |   +  | RGui |
  *   `----------------------------------'                                       `----------------------------------'
  *                                        ,-------------.       ,-------------.
  *                                        | LEFT |RIGHT |       | DOWN | UP   |
@@ -46,69 +42,69 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
  */
 
 [BASE] = LAYOUT_ergodox(  // layer 0 : default
-        // left hand
-        KC_ESC,    KC_1,  KC_2,  KC_3,  KC_4,  KC_5,   KC_GRV,
-        KC_TAB,    KC_Q,  KC_W,  KC_E,  KC_R,  KC_T,   TG(1),
-        KC_CAPS,   KC_A,  KC_S,  KC_D,  KC_F,  KC_G,
-        KC_LSFT,   KC_Z,  KC_X,  KC_C,  KC_V,  KC_B,   MO(2),
-        KC_LCTRL,  KC_RBRC, KC_NONUS_BSLASH,  KC_LALT,  KC_LGUI,
-                                               KC_LEFT, KC_RIGHT,
-                                                              KC_HOME,
-                                               KC_SPC,KC_DEL, KC_END,
-        // right hand
-        KC_PSCREEN,  KC_6,   KC_7,    KC_8,    KC_9,   KC_0,        KC_MINS,
-        TG(1),   KC_Y,   KC_U,    KC_I,    KC_O,   KC_P,        KC_LBRC,
-                     KC_H,   KC_J,    KC_K,    KC_L,   KC_SCLN,     KC_QUOT,
-        MO(2),    KC_N,   KC_M,    KC_COMM, KC_DOT, KC_SLSH,     KC_RSFT,
-                             KC_RCTRL, KC_RALT,   KC_BSLS,  KC_EQL, KC_RGUI,
-        KC_DOWN, KC_UP,
-        KC_PGUP,
-        KC_PGDN, KC_ENT, KC_BSPC
-    ),
+    // left hand
+    KC_ESC,   KC_1,   KC_2,   KC_3,   KC_4,  KC_5,   KC_GRV,
+    KC_TAB,   KC_Q,   KC_W,   KC_E,   KC_R,  KC_T,   TG(1),
+    KC_CAPS,  KC_A,   KC_S,   KC_D,   KC_F,  KC_G,
+    KC_LSFT,  KC_Z,   KC_X,   KC_C,   KC_V,  KC_B,   MO(2),
+    KC_LCTRL, MO(3),  KC_EQL, KC_LGUI, KC_LALT,
+                                            KC_NLCK,  KC_SLCK,
+                                            KC_HOME,
+                                            KC_SPC,   KC_DEL, KC_END,
 
+    // right hand
+    KC_BSLS,  KC_6,   KC_7,   KC_8,   KC_9,   KC_0,   KC_MINS,
+    TG(1),    KC_Y,   KC_U,   KC_I,   KC_O,   KC_P,   KC_LBRC,
+              KC_H,   KC_J,   KC_K,   KC_L,   KC_SCLN,KC_QUOT,
+    MO(2),    KC_N,   KC_M,   KC_COMM,KC_DOT, KC_SLSH,KC_NONUS_BSLASH,
+    KC_LEFT,  KC_DOWN, KC_UP, KC_RIGHT, KC_RBRC,
+    KC_RGUI,  KC_RALT,
+    KC_PGUP,
+    KC_PGDN,  KC_ENT, KC_BSPC
+),
 /* Keymap 1: Basic layer with functions
  *
  *
  *
  * ,--------------------------------------------------.           ,--------------------------------------------------.
- * |  Esc   |  F1  |  F2  |  F3  |  F4  |  F5  |  F11 |           | F12 |  F6  |  F7  |  F8  |  F9  |   0  |   -    |
+ * |        |  F1  |  F2  |  F3  |  F4  |  F5  |  F11 |           | F12  |  F6  |  F7  |  F8  |  F9  |   0  |        |
  * |--------+------+------+------+------+-------------|           |------+------+------+------+------+------+--------|
- * |  Tab   |   Q  |   W  |   E  |   R  |   T  |  L1  |           |  L1  |   Y  |   U  |   I  |   O  |   P  |   Å    |
+ * |        |      |      |      |      |      |      |           |      |      |      |      |      |      |        |
  * |--------+------+------+------+------+------|      |           |      |------+------+------+------+------+--------|
- * |  Caps  |   A  |   S  |   D  |   F  |   G  |------|           |------|   H  |   J  |   K  |   L  |   Ö  |   Ä    |
- * |--------+------+------+------+------+------|  L2  |           |  L2  |------+------+------+------+------+--------|
- * | LShift |   Z  |   X  |   C  |   V  |   B  |      |           |      |   N  |   M  |   ,  |   .  |  -   | RShift |
+ * |        |      |      |      |      |      |------|           |------|      |      |      |      |      |        |
+ * |--------+------+------+------+------+------|      |           |      |------+------+------+------+------+--------|
+ * |        |      |      |      |      |      |      |           |      |      |      |      |      |      |        |
  * `--------+------+------+------+------+-------------'           `-------------+------+------+------+------+--------'
- *   | Ctrl |  ¨^  |  <|>  | Alt | LGui|                                       | Ctrl |  Alt  |  ´`  |   +  | RGui |
+ *   |      |  ¨   |       |     |       |                                       |      |       |      |      |      |
  *   `----------------------------------'                                       `----------------------------------'
  *                                        ,-------------.       ,-------------.
- *                                        | LEFT |RIGHT |       | DOWN | UP   |
+ *                                        |      |      |       |      |      |
  *                                 ,------+------+------|       |------+--------+------.
- *                                 |      |      | Home |       | PgUp |        |      |
- *                                 | Space|Del   |------|       |------|  Enter | Bkspc|
- *                                 |      |      | End  |       | PgDn |        |      |
+ *                                 |      |      |      |       |      |        |      |
+ *                                 |      |      |------|       |------|        |      |
+ *                                 |      |      |      |       |      |        |      |
  *                                 `--------------------'       `----------------------'
  */
 
 [FUNCL] = LAYOUT_ergodox(  // layer 1 : functions
-  // left hand
-  _______,  KC_F1,     KC_F2,     KC_F3,     KC_F4,     KC_F5,     KC_F11,
-  _______,  _______,  _______,  _______,  _______,  _______,  _______,
-  _______,  _______,  _______,  _______,  _______,  _______,
-  _______,  _______,  _______,  _______,  _______,  _______,  _______,
-  _______,  _______,  _______,  _______,  _______,
-                                         _______, _______,
-                                                        _______,
-                                         _______,_______,_______,
-  // right hand
-  KC_F12,  KC_F6,   KC_F7,    KC_F8,    KC_F9,   KC_F10,     _______,
-  _______,    _______,  _______,  _______,  _______,  _______,  _______,
-  _______,  _______,  _______,  _______,  _______,  _______,
-  _______,    _______,  _______,  _______,  _______,  _______,  _______,
-                      _______,  _______,  _______,  _______,  _______,
-  _______, _______,
-  _______,
-  _______, _______, _______
+    // left hand
+    _______,  KC_F1,    KC_F2,    KC_F3,    KC_F4,    KC_F5,    KC_F11,
+    _______,  _______,  _______,  _______,  _______,  _______,  _______,
+    _______,  _______,  _______,  _______,  _______,  _______,
+    _______,  _______,  _______,  _______,  _______,  _______,  _______,
+    _______,  _______,  _______,  _______,  _______,
+                                            _______,  _______,
+                                            _______,
+                                            _______,  _______,  _______,
+    // right hand
+    KC_F12,   KC_F6,    KC_F7,    KC_F8,    KC_F9,    KC_F10,   _______,
+    _______,  _______,  _______,  _______,  _______,  _______,  _______,
+    _______,  _______,  _______,  _______,  _______,  _______,
+    _______,  _______,  _______,  _______,  _______,  _______,  _______,
+    _______,  _______,  _______,  _______,  _______,
+    _______,  _______,
+    _______,
+    _______,  _______,  _______
 ),
 
 /* Keymap 2: Symbol Layer
@@ -134,24 +130,24 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
  */
 // SYMBOLS
 [SYMB] = LAYOUT_ergodox(
-       // left hand
-       KC_TRNS,KC_F1,  KC_F2,  KC_F3,  KC_F4,  KC_F5,  KC_TRNS,
-       KC_TRNS,DE_EXLM,DE_AT,  DE_LCBR,DE_RCBR,DE_PIPE,KC_TRNS,
-       KC_TRNS,DE_HASH,DE_DLR, DE_LPRN,DE_RPRN,DE_GRV,
-       KC_TRNS,DE_PERC,DE_CIRC,DE_LBRC,DE_RBRC,DE_TILD,KC_TRNS,
-       KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,
-                                       RGB_MOD,BL_TOGG,
-                                               BL_INC,
-                               RGB_VAD,RGB_VAI,BL_DEC,
-       // right hand
-       KC_TRNS, KC_F6,   KC_F7,  KC_F8,   KC_F9,   KC_F10,  KC_F11,
-       KC_TRNS, KC_UP,   KC_7,   KC_8,    KC_9,    DE_ASTR, KC_F12,
-                KC_DOWN, KC_4,   KC_5,    KC_6,    DE_PLUS, KC_TRNS,
-       KC_TRNS, DE_AMPR, KC_1,   KC_2,    KC_3,    DE_BSLS, KC_TRNS,
-                         KC_TRNS,KC_DOT,  KC_0,    DE_EQL,  KC_TRNS,
-       RGB_TOG, RGB_SLD,
-       KC_TRNS,
-       KC_TRNS, RGB_HUD, RGB_HUI
+   // left hand
+   _______,  KC_F1,    KC_F2,    KC_F3,    KC_F4,    KC_F5,    KC_F11,
+   _______,  DE_EXLM,  DE_AT,    DE_LCBR,  DE_RCBR,  DE_PIPE,  _______,
+   _______,  DE_HASH,  DE_DLR,   DE_LPRN,  DE_RPRN,  DE_GRV,
+   _______,  DE_PERC,  DE_CIRC,  DE_LBRC,  DE_RBRC,  DE_TILD,  _______,
+   _______,  _______,  _______,  _______,  _______,
+                                           RGB_MOD,  BL_TOGG,
+                                           BL_INC,
+                                           RGB_VAD,  RGB_VAI,  BL_DEC,
+   // right hand
+   KC_F12,   KC_F6,    KC_F7,    KC_F8,    KC_F9,    KC_F10,   KC_F11,
+   _______,  KC_UP,    KC_7,     KC_8,     KC_9,     DE_ASTR,  _______,
+             KC_DOWN,  KC_4,     KC_5,     KC_6,     DE_PLUS,  _______,
+   _______,  DE_AMPR,  KC_1,     KC_2,     KC_3,     DE_BSLS,  _______,
+   _______,  KC_DOT,   KC_0,     DE_EQL,   _______,
+   RGB_TOG,  RGB_SLD,
+   _______,
+   _______,  RGB_HUD,  RGB_HUI
 ),
 
 /* Keymap 3: Media and mouse keys
@@ -175,82 +171,75 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
  *                                 |      |      |      |       |      |      |      |
  *                                 `--------------------'       `--------------------'
  */
+
 // MEDIA AND MOUSE
 [MDIA] = LAYOUT_ergodox(
-       RESET, KC_F1  , KC_F2  , KC_F3  , KC_F4  , KC_F5  , KC_TRNS,
-       KC_TRNS, KC_TRNS, KC_BTN1, KC_MS_U, KC_BTN2, KC_TRNS, KC_TRNS,
-       KC_TRNS, KC_BTN4, KC_MS_L, KC_MS_D, KC_MS_R, KC_BTN5,
-       KC_TRNS, KC_WH_L, KC_WH_D, KC_WH_U, KC_WH_R, KC_BTN3, KC_TRNS,
-       KC_TRNS, KC_TRNS, KC_ACL0, KC_ACL1, KC_ACL2,
-                                           KC_TRNS, KC_TRNS,
-                                                    KC_TRNS,
-                                  KC_BTN1, KC_BTN2, KC_TRNS,
-    // right hand
-       KC_TRNS, KC_F6  , KC_F7  , KC_F8  , KC_F9  , KC_F10 , KC_F11,
-       KC_TRNS, KC_TRNS, KC_VOLD, KC_MUTE, KC_VOLU, KC_TRNS, KC_F12,
-                KC_TRNS, KC_MPRV, KC_MSTP, KC_MPLY, KC_MNXT, KC_TRNS,
-       KC_TRNS, KC_WSCH, KC_WBAK, KC_WHOM, KC_WREF, KC_WFWD, KC_TRNS,
-                         KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
-       KC_TRNS, KC_TRNS,
-       KC_TRNS,
-       KC_TRNS, KC_WBAK, KC_WFWD
+   RESET,    KC_F1,    KC_F2,    KC_F3,    KC_F4,    KC_F5,    KC_F11,
+   _______,  _______,  KC_BTN1,  KC_MS_U,  KC_BTN2,  _______,  _______,
+   _______,  KC_BTN4,  KC_MS_L,  KC_MS_D,  KC_MS_R,  KC_BTN5,
+   _______,  KC_WH_L,  KC_WH_D,  KC_WH_U,  KC_WH_R,  KC_BTN3,  _______,
+   _______,  _______,  KC_ACL0,  KC_ACL1,  KC_ACL2,
+                                           _______,  _______,
+                                           _______,
+                                           KC_BTN1,  KC_BTN2,  _______,
+   // right hand
+   KC_F12,   KC_F6,    KC_F7,    KC_F8,    KC_F9,    KC_F10,   _______,
+   _______, _______,   KC_VOLD,  KC_MUTE,  KC_VOLU,  _______,  _______,
+            _______,   KC_MPRV,  KC_MSTP,  KC_MPLY,  KC_MNXT,  _______,
+   _______, KC_WSCH,   KC_WBAK,  KC_WHOM,  KC_WREF,  KC_WFWD,  _______,
+   _______, _______,   _______,  _______,  _______,
+   _______, _______,
+   _______,
+   _______, KC_WBAK, KC_WFWD
 ),
 };
 
-const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
-{
-  // MACRODOWN only works in this function
-      switch(id) {
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) {
+    // MACRODOWN only works in this function
+    switch (id) {
         case 0:
-        if (record->event.pressed) {
-          SEND_STRING (QMK_KEYBOARD "/" QMK_KEYMAP " @ " QMK_VERSION);
-        }
-        break;
+            if (record->event.pressed) {
+                SEND_STRING(QMK_KEYBOARD "/" QMK_KEYMAP " @ " QMK_VERSION);
+            }
+            break;
         case 1:
-        if (record->event.pressed) { // For resetting EEPROM
-          eeconfig_init();
-        }
-        break;
-      }
+            if (record->event.pressed) {  // For resetting EEPROM
+                eeconfig_init();
+            }
+            break;
+    }
     return MACRO_NONE;
 };
 
 bool process_record_user(uint16_t keycode, keyrecord_t *record) {
-  switch (keycode) {
-    // dynamically generate these.
-    case EPRM:
-      if (record->event.pressed) {
-        eeconfig_init();
-      }
-      return false;
-      break;
-    case VRSN:
-      if (record->event.pressed) {
-        SEND_STRING (QMK_KEYBOARD "/" QMK_KEYMAP " @ " QMK_VERSION);
-      }
-      return false;
-      break;
-    case RGB_SLD:
-      if (record->event.pressed) {
-        #ifdef RGBLIGHT_ENABLE
-          rgblight_mode(1);
-        #endif
-      }
-      return false;
-      break;
-  }
-  return true;
+    switch (keycode) {
+        case VRSN:
+            if (record->event.pressed) {
+                SEND_STRING(QMK_KEYBOARD "/" QMK_KEYMAP " @ " QMK_VERSION);
+            }
+            return false;
+            break;
+        case RGB_SLD:
+            if (record->event.pressed) {
+#ifdef RGBLIGHT_ENABLE
+                rgblight_mode(1);
+#endif
+            }
+            return false;
+            break;
+    }
+    return true;
 }
 
 // Runs just one time when the keyboard initializes.
-void matrix_init_user(void) {
+void matrix_init_user(void){
 
 };
 
 // Runs constantly in the background, in a loop.
 void matrix_scan_user(void) {
-
     uint8_t layer = biton32(layer_state);
+
     ergodox_board_led_off();
     ergodox_right_led_1_off();
     ergodox_right_led_2_off();
@@ -262,8 +251,10 @@ void matrix_scan_user(void) {
         case 2:
             ergodox_right_led_2_on();
             break;
+        case 3:
+            ergodox_right_led_3_on();
+            break;
         default:
-            // none
             break;
     }
 };

keyboards/foxlab/leaf60/universal/keymaps/mguterl/config.h

@@ -0,0 +1,19 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here

keyboards/foxlab/leaf60/universal/keymaps/mguterl/keymap.c

@@ -0,0 +1,43 @@
+/* Copyright 2019 Fox Lab
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+#include "mguterl.h"
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+	[_QWERTY] = LAYOUT_all(
+		KC_GESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSLS, KC_GRV,
+		HPR_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSPC,
+		ESC_CTL, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT,
+		KC_LSFT, KC_NO, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, MO(UTIL),
+		KC_LALT, KC_LALT, KC_LGUI, SPC_UTL, SPC_UTL, SPC_UTL, KC_RALT, MO(1), KC_RGUI, KC_RCTL),
+
+	[_GAMING] = LAYOUT_all(
+		KC_ESC,  _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+		KC_TAB,  _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+		_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+		_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+		_______, _______, _______, _______, KC_SPC,  _______, _______, _______, _______, _______),
+
+	[_UTIL] = LAYOUT_all(
+		RESET,   KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, _______, _______,
+		TG_GAME, KC_MPLY, KC_MPRV, KC_MNXT, _______, _______, KC_HOME, KC_PGDN, KC_PGUP, KC_END, _______, _______, _______, _______,
+		_______, KC_VOLD, KC_VOLU, KC_MUTE, _______, _______, KC_LEFT, KC_DOWN, KC_UP,   KC_RGHT, _______, _______, _______,
+		_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+		_______, _______, _______, _______, _______, _______, _______, _______, _______, _______)
+
+
+};

keyboards/foxlab/leaf60/universal/keymaps/mguterl/readme.md

@@ -0,0 +1,11 @@
+# Michael Guterl's Leaf60 WKL Layout
+
+Check out my [userspace](/users/mguterl) for the custom keycodes that are used
+in keymap.c.
+
+This is a pretty standard 60% WKL layout. I add a couple of layers to add
+some conveniences and add vimkeys for navigation.
+
+```sh
+make foxlab/leaf60/universal:mguterl:flash
+```

keyboards/hadron/ver2/rules.mk

@@ -1,48 +1,14 @@
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = halfkay
 
 # Build Options

keyboards/halberd/rules.mk

@@ -1,63 +1,16 @@
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
 # Build Options
 #   change yes to no to disable
 #

keyboards/handwired/2x5keypad/rules.mk

@@ -1,4 +1,14 @@
+# MCU name
 MCU = atmega32u4
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = caterina
 
 BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration

keyboards/handwired/412_64/rules.mk

@@ -1,53 +1,14 @@
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-# Bootloader
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded 
-#     automatically (+60). See bootloader.mk for all options.
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 # Build Options

keyboards/handwired/arrow_pad/rules.mk

@@ -1,51 +1,15 @@
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=512
-
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = halfkay
 
 # Build Options
 #   change yes to no to disable

keyboards/handwired/atreus50/rules.mk

@@ -1,49 +1,15 @@
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = caterina
 
 # Build Options
 #   change to "no" to disable the options, or define them in the Makefile in 

keyboards/handwired/cmd60/rules.mk

@@ -1,52 +1,15 @@
-
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=512
-
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = halfkay
 
 # Build Options
 #   change yes to no to disable
@@ -65,5 +28,3 @@ MIDI_ENABLE = no            # MIDI controls
 UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
-
-

keyboards/handwired/co60/rev1/rules.mk

@@ -1,49 +1,14 @@
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 # Build Options

keyboards/handwired/dactyl/rules.mk

@@ -1,71 +1,15 @@
-#----------------------------------------------------------------------------
-# On command line:
-#
-# make = Make software.
-#
-# make clean = Clean out built project files.
-#
-# That's pretty much all you need. To compile, always go make clean,
-# followed by make.
-#
-# For advanced users only:
-# make teensy = Download the hex file to the device, using teensy_loader_cli.
-#               (must have teensy_loader_cli installed).
-#
-#----------------------------------------------------------------------------
-
-# # project specific files
-SRC = twimaster.c \
-	  matrix.c
-
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=512
-
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = halfkay
 
 # Build Options
 #   comment out to disable the options.
@@ -84,3 +28,7 @@ SWAP_HANDS_ENABLE       = yes # Allow swapping hands of keyboard
 SLEEP_LED_ENABLE        = no
 API_SYSEX_ENABLE        = no
 RGBLIGHT_ENABLE         = no
+
+# project specific files
+SRC = twimaster.c \
+	  matrix.c

keyboards/handwired/dactyl_manuform/5x6/keymaps/rishka/config.h

@@ -0,0 +1,41 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+
+#pragma once
+
+
+// #define USE_SERIAL
+#define USE_I2C
+// #define MASTER_LEFT
+// #define MASTER_RIGHT
+#define EE_HANDS
+// Rows are doubled-up
+// #define DEBOUNCE 5
+#define TAPPING_TOGGLE 3
+#define ONESHOT_TAP_TOGGLE 3
+#define PERMISSIVE_HOLD
+#define IGNORE_MOD_TAP_INTERRUPT
+#define TAPPING_TERM 300
+#ifdef RGBLED_NUM
+#  undef RGBLED_NUM
+#endif
+#define RGBLED_NUM 54
+#define RGBLIGHT_LIMIT_VAL 200
+#define RGBLIGHT_ANIMATIONS
+// #define RGBLIGHT_LED_MAP { 11,10,9,8,7,6,5,4,3,2,1,0,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26 }
+#define RGBLIGHT_SPLIT 27

keyboards/handwired/dactyl_manuform/5x6/keymaps/rishka/keymap.c

@@ -0,0 +1,61 @@
+/* A standard layout for the Dactyl Manuform 5x6 Keyboard */
+
+#include QMK_KEYBOARD_H
+#include "rishka.h"
+
+enum layers {
+  BASE, // default layer
+  WIN, // Switch keys that are needed in windows
+  SYMB, // symbols
+  MDIA // media keys
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+  [BASE] = LAYOUT_5x6_wrapper(
+     KC_EQL , ________________NUMBERS_L__________________,                         ________________NUMBERS_R__________________, KC_MINS,
+     KC_ESC , _________________QWERTY_L1_________________,                         _________________QWERTY_R1_________________, KC_BSLS,
+     KC_F1  , _____________MOD_QWERTY_L2_________________,                         _____________MOD_QWERTY_R2_________________, KC_QUOT,
+     OS_LSFT, _________________QWERTY_L3_________________,                         _________________QWERTY_R3_________________, OS_RSFT,
+                      KC_LEFT,KC_RGHT,                                                       KC_UP, KC_DOWN,
+                                     KC_BSPC, KC_SPC,                         KC_TAB, KC_ENT,
+                                     KC_LGUI, MO(SYMB),                       MO(SYMB), TT(MDIA),
+                                     KC_DEL, KC_GRV,                          TT(WIN), KC_LALT
+  ),
+  [WIN] = LAYOUT_5x6_wrapper(
+
+     _______, _______, _______, _______, _______, _______,                        _______, _______, _______, _______, _______, _______,
+     _______, _______, _______, _______, _______, _______,                        _______, _______, _______, _______, _______, _______,
+     _______, _________________QWERTY_L2_________________,                        _______, _______, _______, _______, _______, _______,
+     _______, _______, _______, _______, _______, _______,                        _______, _______, _______, _______, _______, _______,
+                                             _______, _______,            _______, _______,
+                                             _______, _______,            _______, _______,
+                                             KC_LCTL, _______,            _______, _______,
+                                             _______, _______,            _______, _______
+  ),
+
+  [SYMB] = LAYOUT_5x6_wrapper(
+       KC_F12 , ______________________F_L__________________,                      ______________________F_R__________________, KC_F11,
+       _______, _________________SYMBOL_L1_________________,                      _________________SYMBOL_R1_________________, KC_NLCK,
+       _______, _________________SYMBOL_L2_________________,                      _________________SYMBOL_R2_________________, _______,
+       _______, _________________SYMBOL_L3_________________,                      _________________SYMBOL_R3_________________, _______,
+                                               _______, _______,            KC_P0 , KC_PDOT,
+                                               _______, _______,            _______, _______,
+                                               RESET  , _______,            _______, _______,
+                                               RGB_TOG, _______,            _______, _______
+  ),
+  [MDIA] = LAYOUT_5x6_wrapper(
+
+     RGB_MOD, RGB_HUI, _______, _______, _______, _______,                        _______, _______, _______, _______, _______, _______,
+     	RGB_M_SN, RGB_HUD, _______, KC_MS_U, _______, KC_WH_U,                        _______, _______, KC_WH_U, _______, _______, _______,
+     RGB_VAI, RGB_SAI, KC_MS_L, KC_MS_D, KC_MS_R, KC_WH_D,                        _______, MOUSE_L, KC_WH_D, MOUSE_R, _______, _______,
+     RGB_VAD, RGB_SAD, _______, _______, _______, _______,                        _______, _______, _______, _______, _______, _______,
+                                             _______, _______,            _______, _______,
+                                             KC_BTN1, KC_BTN2,            _______, _______,
+                                             KC_BTN3, KC_BTN4,            _______, _______,
+                                             KC_BTN5, _______,            _______, _______
+
+   ),
+};
+
+

keyboards/handwired/dactyl_manuform/5x6/keymaps/rishka/rules.mk

@@ -1,2 +1,3 @@
+BOOTLOADER=qmk-dfu
 RGBLIGHT_ENABLE = yes
 

keyboards/handwired/dactyl_manuform/rules.mk

@@ -1,47 +1,16 @@
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Bootloader
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = caterina
 
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
 # Build Options
 #   change to "no" to disable the options, or define them in the Makefile in
 #   the appropriate keymap folder that will get included automatically

keyboards/handwired/dactyl_promicro/rules.mk

@@ -1,47 +1,16 @@
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Bootloader
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = caterina
 
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
 # Build Options
 #   change to "no" to disable the options, or define them in the Makefile in
 #   the appropriate keymap folder that will get included automatically

keyboards/handwired/fivethirteen/rules.mk

@@ -1,52 +1,15 @@
-
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=512
-
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = halfkay
 
 # Build Options
 #   change yes to no to disable

keyboards/handwired/frenchdev/rules.mk

@@ -1,70 +1,15 @@
-#----------------------------------------------------------------------------
-# On command line:
-#
-# make = Make software.
-#
-# make clean = Clean out built project files.
-#
-# That's pretty much all you need. To compile, always go make clean,
-# followed by make.
-#
-# For advanced users only:
-# make teensy = Download the hex file to the device, using teensy_loader_cli.
-#               (must have teensy_loader_cli installed).
-#
-#----------------------------------------------------------------------------
-
-# # project specific files
-SRC = i2c_master.c \
-	  matrix.c
-
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-BOOTLOADER = halfKay
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = halfkay
 
 # Build Options
 #   comment out to disable the options.
@@ -85,3 +30,7 @@ BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 RGBLIGHT_ENABLE = no
 API_SYSEX_ENABLE = no
+
+# project specific files
+SRC = i2c_master.c \
+	  matrix.c

keyboards/handwired/gamenum/rules.mk

@@ -1,52 +1,15 @@
-
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=512
-
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = caterina
 
 # Build Options
 #   change yes to no to disable
@@ -65,5 +28,3 @@ MIDI_ENABLE = no            # MIDI controls
 UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
-
-

keyboards/handwired/hacked_motospeed/config.h

@@ -43,7 +43,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 
 //                        WR  XR  YR  ZR  VR  ZL  YL  XL  WL  VL
-#define MATRIX_ROW_PINS { B3, B5, F1, B4, B6, D5, D4, D6, D7, C4}
+#define MATRIX_ROW_PINS { B3, B4, F1, B5, B6, D5, D4, D6, D7, C4}
 
 //                        ER  DR  CR  BR  AR  FR  FL  AL  BL  CL  DL  EL
 #define MATRIX_COL_PINS { F7, F6, F5, F4, F3, F2, E0, E1, C0, C1, C2, C3 }
@@ -120,7 +120,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
  * power-up.
  *
  */
-#define FORCE_NKRO
 
 /*
  * Magic Key Options

keyboards/handwired/hacked_motospeed/keymaps/german/keymap.c

@@ -0,0 +1,10 @@
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+[0] = LAYOUT(KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, LSFT(KC_8), LSFT(KC_9), KC_PEQL, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, LSFT(KC_MINS), MO(2), MO(6), KC_TAB, KC_BSPC, KC_SPC, MO(1), KC_LCTL, KC_LALT, MO(4), KC_LGUI, MO(2)),
+[1] = LAYOUT(LALT(KC_F4), LSFT(KC_Q), LSFT(KC_W), LSFT(KC_E), LSFT(KC_R), LSFT(KC_T), LSFT(KC_Y), LSFT(KC_U), LSFT(KC_I), LSFT(KC_O), LSFT(KC_P), LSFT(KC_A), LSFT(KC_S), LSFT(KC_D), LSFT(KC_F), LSFT(KC_G), LSFT(KC_H), LSFT(KC_J), LSFT(KC_K), LSFT(KC_L), RALT(KC_7), RALT(KC_0), KC_NUHS, LSFT(KC_Z), LSFT(KC_X), LSFT(KC_C), LSFT(KC_V), LSFT(KC_B), LSFT(KC_N), LSFT(KC_M), LSFT(KC_COMM), LSFT(KC_DOT), LSFT(KC_1), MO(3), TG(6), LSFT(KC_TAB), KC_DEL, KC_ENT, KC_TRNS, LSFT(KC_LCTL), LSFT(KC_LALT), LSFT(KC_RALT), LSFT(KC_LGUI), MO(3)),
+[2] = LAYOUT(LSFT(KC_GRV), RALT(KC_Q), KC_JYEN, RALT(KC_E), LSFT(KC_4), LSFT(KC_5), LSFT(KC_6), KC_LBRC, KC_UP, KC_SCLN, KC_PSCR, KC_QUOT, KC_MINS, LSFT(KC_7), LSFT(KC_2), LSFT(KC_NUHS), LSFT(KC_3), KC_LEFT, KC_DOWN, KC_RGHT, KC_NUBS, LSFT(KC_NUBS), RALT(KC_RBRC), KC_GRV, LSFT(KC_RBRC), KC_SLSH, KC_RBRC, RALT(KC_NUBS), KC_HOME, KC_PGDN, KC_PGUP, KC_END, RALT(KC_6), KC_TRNS, KC_CAPS, KC_TAB, KC_DEL, KC_ENT, MO(3), OUT_BT, OUT_USB, OUT_AUTO, BL_STEP, KC_TRNS),
+[3] = LAYOUT(LSFT(KC_GRV), RALT(KC_Q), KC_JYEN, RALT(KC_E), LSFT(KC_4), LSFT(KC_5), LSFT(KC_6), LSFT(KC_LBRC), KC_UP, LSFT(KC_SCLN), KC_PSCR, LSFT(KC_QUOT), KC_MINS, RALT(KC_MINS), LSFT(KC_EQL), KC_EQL, LSFT(KC_3), KC_LEFT, KC_DOWN, KC_RGHT, RALT(KC_8), RALT(KC_9), RALT(KC_RBRC), KC_GRV, LSFT(KC_RBRC), LSFT(KC_SLSH), KC_RBRC, RALT(KC_NUBS), KC_HOME, KC_PGDN, KC_PGUP, KC_END, RALT(KC_6), KC_TRNS, KC_CAPS, LSFT(KC_TAB), LSFT(KC_DEL), LSFT(KC_ENT), KC_TRNS, RSFT(KC_RCTL), RSFT(KC_LALT), RSFT(KC_RALT), RSFT(KC_RGUI), KC_TRNS),
+[4] = LAYOUT(RALT(KC_ESC), RALT(KC_Q), RALT(KC_W), RALT(KC_E), RALT(KC_R), RALT(KC_T), RALT(KC_Y), RALT(KC_U), RALT(KC_I), RALT(KC_O), RALT(KC_P), RALT(KC_A), RALT(KC_S), RALT(KC_D), RALT(KC_F), RALT(KC_G), RALT(KC_H), RALT(KC_J), RALT(KC_K), RALT(KC_L), RALT(KC_8), RALT(KC_9), LSFT(KC_0), RALT(KC_Z), RALT(KC_X), RALT(KC_C), RALT(KC_V), RALT(KC_B), RALT(KC_N), RALT(KC_M), RALT(KC_COMM), RALT(KC_DOT), RALT(KC_6), KC_NO, RALT(KC_ENT), RALT(KC_TAB), RALT(KC_DEL), RALT(KC_SPC), RALT(KC_LSFT), RALT(KC_LCTL), RALT(KC_LALT), KC_TRNS, RALT(KC_LGUI), KC_NO),
+[5] = LAYOUT(KC_0, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_F11, KC_F12, KC_F13, KC_F14, KC_F15, KC_F16, KC_F17, KC_F18, KC_F19, KC_F20, KC_F21, KC_F22, KC_F23, KC_NO, KC_TRNS, KC_TAB, KC_BSPC, KC_SPC, KC_LSFT, KC_LCTL, KC_LALT, KC_RALT, KC_LGUI, KC_NO)
+};

keyboards/handwired/hacked_motospeed/keymaps/german/layers.json

@@ -0,0 +1 @@
+[["KC_ESC", "KC_Q", "KC_W", "KC_E", "KC_R", "KC_T", "KC_Y", "KC_U", "KC_I", "KC_O", "KC_P", "KC_A", "KC_S", "KC_D", "KC_F", "KC_G", "KC_H", "KC_J", "KC_K", "KC_L", "LSFT(KC_8)", "LSFT(KC_9)", "KC_PEQL", "KC_Z", "KC_X", "KC_C", "KC_V", "KC_B", "KC_N", "KC_M", "KC_COMM", "KC_DOT", "LSFT(KC_MINS)", "MO(2)", "MO(6)", "KC_TAB", "KC_BSPC", "KC_SPC", "MO(1)", "KC_LCTL", "KC_LALT", "MO(4)", "KC_LGUI", "MO(2)"], ["LALT(KC_F4)", "LSFT(KC_Q)", "LSFT(KC_W)", "LSFT(KC_E)", "LSFT(KC_R)", "LSFT(KC_T)", "LSFT(KC_Y)", "LSFT(KC_U)", "LSFT(KC_I)", "LSFT(KC_O)", "LSFT(KC_P)", "LSFT(KC_A)", "LSFT(KC_S)", "LSFT(KC_D)", "LSFT(KC_F)", "LSFT(KC_G)", "LSFT(KC_H)", "LSFT(KC_J)", "LSFT(KC_K)", "LSFT(KC_L)", "RALT(KC_7)", "RALT(KC_0)", "KC_NUHS", "LSFT(KC_Z)", "LSFT(KC_X)", "LSFT(KC_C)", "LSFT(KC_V)", "LSFT(KC_B)", "LSFT(KC_N)", "LSFT(KC_M)", "LSFT(KC_COMM)", "LSFT(KC_DOT)", "LSFT(KC_1)", "MO(3)", "TG(6)", "LSFT(KC_TAB)", "KC_DEL", "KC_ENT", "KC_TRNS", "LSFT(KC_LCTL)", "LSFT(KC_LALT)", "LSFT(KC_RALT)", "LSFT(KC_LGUI)", "MO(3)"], ["LSFT(KC_GRV)", "RALT(KC_Q)", "KC_JYEN", "RALT(KC_E)", "LSFT(KC_4)", "LSFT(KC_5)", "LSFT(KC_6)", "KC_LBRC", "KC_UP", "KC_SCLN", "KC_PSCR", "KC_QUOT", "KC_MINS", "LSFT(KC_7)", "LSFT(KC_2)", "LSFT(KC_NUHS)", "LSFT(KC_3)", "KC_LEFT", "KC_DOWN", "KC_RGHT", "KC_NUBS", "LSFT(KC_NUBS)", "RALT(KC_RBRC)", "KC_GRV", "LSFT(KC_RBRC)", "KC_SLSH", "KC_RBRC", "RALT(KC_NUBS)", "KC_HOME", "KC_PGDN", "KC_PGUP", "KC_END", "RALT(KC_6)", "KC_TRNS", "KC_CAPS", "KC_TAB", "KC_DEL", "KC_ENT", "MO(3)", "OUT_BT", "OUT_USB", "OUT_AUTO", "BL_STEP", "KC_TRNS"], ["LSFT(KC_GRV)", "RALT(KC_Q)", "KC_JYEN", "RALT(KC_E)", "LSFT(KC_4)", "LSFT(KC_5)", "LSFT(KC_6)", "LSFT(KC_LBRC)", "KC_UP", "LSFT(KC_SCLN)", "KC_PSCR", "LSFT(KC_QUOT)", "KC_MINS", "RALT(KC_MINS)", "LSFT(KC_EQL)", "KC_EQL", "LSFT(KC_3)", "KC_LEFT", "KC_DOWN", "KC_RGHT", "RALT(KC_8)", "RALT(KC_9)", "RALT(KC_RBRC)", "KC_GRV", "LSFT(KC_RBRC)", "LSFT(KC_SLSH)", "KC_RBRC", "RALT(KC_NUBS)", "KC_HOME", "KC_PGDN", "KC_PGUP", "KC_END", "RALT(KC_6)", "KC_TRNS", "KC_CAPS", "LSFT(KC_TAB)", "LSFT(KC_DEL)", "LSFT(KC_ENT)", "KC_TRNS", "RSFT(KC_RCTL)", "RSFT(KC_LALT)", "RSFT(KC_RALT)", "RSFT(KC_RGUI)", "KC_TRNS"], ["RALT(KC_ESC)", "RALT(KC_Q)", "RALT(KC_W)", "RALT(KC_E)", "RALT(KC_R)", "RALT(KC_T)", "RALT(KC_Y)", "RALT(KC_U)", "RALT(KC_I)", "RALT(KC_O)", "RALT(KC_P)", "RALT(KC_A)", "RALT(KC_S)", "RALT(KC_D)", "RALT(KC_F)", "RALT(KC_G)", "RALT(KC_H)", "RALT(KC_J)", "RALT(KC_K)", "RALT(KC_L)", "RALT(KC_8)", "RALT(KC_9)", "LSFT(KC_0)", "RALT(KC_Z)", "RALT(KC_X)", "RALT(KC_C)", "RALT(KC_V)", "RALT(KC_B)", "RALT(KC_N)", "RALT(KC_M)", "RALT(KC_COMM)", "RALT(KC_DOT)", "RALT(KC_6)", "KC_NO", "RALT(KC_ENT)", "RALT(KC_TAB)", "RALT(KC_DEL)", "RALT(KC_SPC)", "RALT(KC_LSFT)", "RALT(KC_LCTL)", "RALT(KC_LALT)", "KC_TRNS", "RALT(KC_LGUI)", "KC_NO"], ["KC_0", "KC_F1", "KC_F2", "KC_F3", "KC_F4", "KC_F5", "KC_F6", "KC_F7", "KC_F8", "KC_F9", "KC_F10", "KC_1", "KC_2", "KC_3", "KC_4", "KC_5", "KC_6", "KC_7", "KC_8", "KC_9", "KC_F11", "KC_F12", "KC_F13", "KC_F14", "KC_F15", "KC_F16", "KC_F17", "KC_F18", "KC_F19", "KC_F20", "KC_F21", "KC_F22", "KC_F23", "KC_NO", "KC_TRNS", "KC_TAB", "KC_BSPC", "KC_SPC", "KC_LSFT", "KC_LCTL", "KC_LALT", "KC_RALT", "KC_LGUI", "KC_NO"]]

keyboards/handwired/hacked_motospeed/keymaps/german/readme.md

@@ -0,0 +1,13 @@
+# Generated Keymap Layout
+
+This layout was generated by the QMK API. You can find the JSON data used to
+generate this keymap in the file layers.json.
+
+To make use of this file you will need follow the following steps:
+
+* Download or Clone QMK Firmware: <https://github.com/qmk/qmk_firmware/>
+* Extract QMK Firmware to a location on your hard drive
+* Copy this folder into %s
+* You are now ready to compile or use your keymap with the source
+
+More information can be found in the QMK docs: <https://docs.qmk.fm>

keyboards/handwired/hacked_motospeed/rules.mk

@@ -22,7 +22,7 @@ COMMAND_ENABLE = yes        # Commands for debug and configuration
 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
 SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
 # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE = yes            # USB Nkey Rollover
+NKRO_ENABLE = no            # USB Nkey Rollover
 BACKLIGHT_ENABLE = yes       # Enable keyboard backlight functionality on B7 by default
 RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
 MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
@@ -31,3 +31,5 @@ BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
+NO_USB_STARTUP_CHECK = yes  # Disable initialization only when usb is plugged in
+BLUETOOTH = RN42

keyboards/handwired/hexon38/rules.mk

@@ -1,54 +1,16 @@
-# see https://github.com/pepaslabs/hexon38
-
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = halfkay
 
-
 # Enabled build options:
 BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
 MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)

keyboards/handwired/hnah108/hnah108.h

@@ -40,14 +40,14 @@
 }
 
 #define LAYOUT_fullsize_iso( \
-    k00,      k01, k02, k03, k04, k05, k06, k07, k08, k09, k0A, k60, k61,     k62, k63, k64,                          \
+    k00,      k01, k02, k03, k04, k05, k06, k07, k08, k09, k0A, k60, k61,     k62, k63, k64,      k65, k66, k67, k68, \
     k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1A, k70, k71, k72,     k73, k74, k75,      k76, k77, k78, k69,  \
     k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k80, k81,          k83, k84, k85,      k86, k87, k79, k6A, \
     k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k91, k93, k94,                         k96, k97, k88, \
     k40, k41, k42, k43, k44, k45, k46, k47, k48, k49, k4A, k90,      k92,          k95,           k98, k99, k89, k7A, \
     k50, k51, k52,                k53,                k54, k55, k56, k57,     k58, k59, k5A,      k9A,      k8A \
 ) LAYOUT_all( \
-    k00,      k01, k02, k03, k04, k05, k06, k07, k08, k09, k0A, k60, k61,     k62, k63, k64,      KC_NO, KC_NO, KC_NO, KC_NO, \
+    k00,      k01, k02, k03, k04, k05, k06, k07, k08, k09, k0A, k60, k61,     k62, k63, k64,      k65, k66, k67, k68, \
     k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1A, k70, k71, k72,     k73, k74, k75,      k76, k77, k78, k69,  \
     k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k80, k81, KC_NO,   k83, k84, k85,      k86, k87, k79, k6A, \
     k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k91, k93, k94,                         k96, k97, k88, \
@@ -56,14 +56,14 @@
 )
 
 #define LAYOUT_fullsize_ansi( \
-    k00,      k01, k02, k03, k04, k05, k06, k07, k08, k09, k0A, k60, k61,     k62, k63, k64,                          \
+    k00,      k01, k02, k03, k04, k05, k06, k07, k08, k09, k0A, k60, k61,     k62, k63, k64,      k65, k66, k67, k68,  \
     k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1A, k70, k71, k72,     k73, k74, k75,      k76, k77, k78, k69,  \
     k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k80, k81, k82,     k83, k84, k85,      k86, k87, k79, k6A, \
     k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k91,      k94,                         k96, k97, k88, \
     k40,      k42, k43, k44, k45, k46, k47, k48, k49, k4A, k90,      k92,          k95,           k98, k99, k89, k7A, \
     k50, k51, k52,                k53,                k54, k55, k56, k57,     k58, k59, k5A,      k9A,      k8A \
 ) LAYOUT_all( \
-    k00,      k01, k02, k03, k04, k05, k06, k07, k08, k09, k0A, k60, k61,     k62, k63, k64,      KC_NO, KC_NO, KC_NO, KC_NO, \
+    k00,      k01, k02, k03, k04, k05, k06, k07, k08, k09, k0A, k60, k61,     k62, k63, k64,      k65, k66, k67, k68, \
     k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1A, k70, k71, k72,     k73, k74, k75,      k76, k77, k78, k69,  \
     k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k80, k81, k82,     k83, k84, k85,      k86, k87, k79, k6A, \
     k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k91,KC_NO,k94,                         k96, k97, k88, \

keyboards/handwired/hnah108/info.json

@@ -6,13 +6,13 @@
     "height": 6.25, 
     "layouts": {
         "LAYOUT_all": {
-            "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"F1", "x":2, "y":0}, {"label":"F2", "x":3, "y":0}, {"label":"F3", "x":4, "y":0}, {"label":"F4", "x":5, "y":0}, {"label":"F5", "x":6.5, "y":0}, {"label":"F6", "x":7.5, "y":0}, {"label":"F7", "x":8.5, "y":0}, {"label":"F8", "x":9.5, "y":0}, {"label":"F9", "x":11, "y":0}, {"label":"F10", "x":12, "y":0}, {"label":"F11", "x":13, "y":0}, {"label":"F12", "x":14, "y":0}, {"label":"PrtSc", "x":15.25, "y":0}, {"label":"Scroll Lock", "x":16.25, "y":0}, {"label":"Pause", "x":17.25, "y":0}, {"x":18.5, "y":0}, {"x":19.5, "y":0}, {"x":20.5, "y":0}, {"x":21.5, "y":0}, {"label":"~", "x":0, "y":1.25}, {"label":"!", "x":1, "y":1.25}, {"label":"@", "x":2, "y":1.25}, {"label":"#", "x":3, "y":1.25}, {"label":"$", "x":4, "y":1.25}, {"label":"%", "x":5, "y":1.25}, {"label":"^", "x":6, "y":1.25}, {"label":"&", "x":7, "y":1.25}, {"label":"*", "x":8, "y":1.25}, {"label":"(", "x":9, "y":1.25}, {"label":")", "x":10, "y":1.25}, {"label":"_", "x":11, "y":1.25}, {"label":"+", "x":12, "y":1.25}, {"label":"Backspace", "x":13, "y":1.25, "w":2}, {"label":"Insert", "x":15.25, "y":1.25}, {"label":"Home", "x":16.25, "y":1.25}, {"label":"PgUp", "x":17.25, "y":1.25}, {"label":"Num Lock", "x":18.5, "y":1.25}, {"label":"/", "x":19.5, "y":1.25}, {"label":"*", "x":20.5, "y":1.25}, {"label":"-", "x":21.5, "y":1.25}, {"label":"Tab", "x":0, "y":2.25, "w":1.5}, {"label":"Q", "x":1.5, "y":2.25}, {"label":"W", "x":2.5, "y":2.25}, {"label":"E", "x":3.5, "y":2.25}, {"label":"R", "x":4.5, "y":2.25}, {"label":"T", "x":5.5, "y":2.25}, {"label":"Y", "x":6.5, "y":2.25}, {"label":"U", "x":7.5, "y":2.25}, {"label":"I", "x":8.5, "y":2.25}, {"label":"O", "x":9.5, "y":2.25}, {"label":"P", "x":10.5, "y":2.25}, {"label":"{", "x":11.5, "y":2.25}, {"label":"}", "x":12.5, "y":2.25}, {"label":"Enter", "x":13.75, "y":2.25, "w":1.25, "h":2}, {"label":"Delete", "x":15.25, "y":2.25}, {"label":"End", "x":16.25, "y":2.25}, {"label":"PgDn", "x":17.25, "y":2.25}, {"label":"7", "x":18.5, "y":2.25}, {"label":"8", "x":19.5, "y":2.25}, {"label":"9", "x":20.5, "y":2.25}, {"label":"+", "x":21.5, "y":2.25, "h":2}, {"label":"Caps Lock", "x":0, "y":3.25, "w":1.75}, {"label":"A", "x":1.75, "y":3.25}, {"label":"S", "x":2.75, "y":3.25}, {"label":"D", "x":3.75, "y":3.25}, {"label":"F", "x":4.75, "y":3.25}, {"label":"G", "x":5.75, "y":3.25}, {"label":"H", "x":6.75, "y":3.25}, {"label":"J", "x":7.75, "y":3.25}, {"label":"K", "x":8.75, "y":3.25}, {"label":"L", "x":9.75, "y":3.25}, {"label":":", "x":10.75, "y":3.25}, {"label":"@", "x":11.75, "y":3.25}, {"label":"~", "x":12.75, "y":3.25}, {"label":"4", "x":18.5, "y":3.25}, {"label":"5", "x":19.5, "y":3.25}, {"label":"6", "x":20.5, "y":3.25}, {"label":"Shift", "x":0, "y":4.25, "w":1.25}, {"label":"|", "x":1.25, "y":4.25}, {"label":"Z", "x":2.25, "y":4.25}, {"label":"X", "x":3.25, "y":4.25}, {"label":"C", "x":4.25, "y":4.25}, {"label":"V", "x":5.25, "y":4.25}, {"label":"B", "x":6.25, "y":4.25}, {"label":"N", "x":7.25, "y":4.25}, {"label":"M", "x":8.25, "y":4.25}, {"label":"<", "x":9.25, "y":4.25}, {"label":">", "x":10.25, "y":4.25}, {"label":"?", "x":11.25, "y":4.25}, {"label":"Shift", "x":12.25, "y":4.25, "w":2.75}, {"label":"\u2191", "x":16.25, "y":4.25}, {"label":"1", "x":18.5, "y":4.25}, {"label":"2", "x":19.5, "y":4.25}, {"label":"3", "x":20.5, "y":4.25}, {"label":"Enter", "x":21.5, "y":4.25, "h":2}, {"label":"Ctrl", "x":0, "y":5.25, "w":1.25}, {"label":"Win", "x":1.25, "y":5.25, "w":1.25}, {"label":"Alt", "x":2.5, "y":5.25, "w":1.25}, {"x":3.75, "y":5.25, "w":6.25}, {"label":"Alt", "x":10, "y":5.25, "w":1.25}, {"label":"Win", "x":11.25, "y":5.25, "w":1.25}, {"label":"Menu", "x":12.5, "y":5.25, "w":1.25}, {"label":"Ctrl", "x":13.75, "y":5.25, "w":1.25}, {"label":"\u2190", "x":15.25, "y":5.25}, {"label":"\u2193", "x":16.25, "y":5.25}, {"label":"\u2192", "x":17.25, "y":5.25}, {"label":"0", "x":18.5, "y":5.25, "w":2}, {"label":".", "x":20.5, "y":5.25}]
+            "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"F1", "x":2, "y":0}, {"label":"F2", "x":3, "y":0}, {"label":"F3", "x":4, "y":0}, {"label":"F4", "x":5, "y":0}, {"label":"F5", "x":6.5, "y":0}, {"label":"F6", "x":7.5, "y":0}, {"label":"F7", "x":8.5, "y":0}, {"label":"F8", "x":9.5, "y":0}, {"label":"F9", "x":11, "y":0}, {"label":"F10", "x":12, "y":0}, {"label":"F11", "x":13, "y":0}, {"label":"F12", "x":14, "y":0}, {"label":"PrtSc", "x":15.25, "y":0}, {"label":"Scroll Lock", "x":16.25, "y":0}, {"label":"Pause", "x":17.25, "y":0}, {"x":18.5, "y":0}, {"x":19.5, "y":0}, {"x":20.5, "y":0}, {"x":21.5, "y":0}, {"label":"~", "x":0, "y":1.25}, {"label":"!", "x":1, "y":1.25}, {"label":"@", "x":2, "y":1.25}, {"label":"#", "x":3, "y":1.25}, {"label":"$", "x":4, "y":1.25}, {"label":"%", "x":5, "y":1.25}, {"label":"^", "x":6, "y":1.25}, {"label":"&", "x":7, "y":1.25}, {"label":"*", "x":8, "y":1.25}, {"label":"(", "x":9, "y":1.25}, {"label":")", "x":10, "y":1.25}, {"label":"_", "x":11, "y":1.25}, {"label":"+", "x":12, "y":1.25}, {"label":"Backspace", "x":13, "y":1.25, "w":2}, {"label":"Insert", "x":15.25, "y":1.25}, {"label":"Home", "x":16.25, "y":1.25}, {"label":"PgUp", "x":17.25, "y":1.25}, {"label":"Num Lock", "x":18.5, "y":1.25}, {"label":"/", "x":19.5, "y":1.25}, {"label":"*", "x":20.5, "y":1.25}, {"label":"-", "x":21.5, "y":1.25}, {"label":"Tab", "x":0, "y":2.25, "w":1.5}, {"label":"Q", "x":1.5, "y":2.25}, {"label":"W", "x":2.5, "y":2.25}, {"label":"E", "x":3.5, "y":2.25}, {"label":"R", "x":4.5, "y":2.25}, {"label":"T", "x":5.5, "y":2.25}, {"label":"Y", "x":6.5, "y":2.25}, {"label":"U", "x":7.5, "y":2.25}, {"label":"I", "x":8.5, "y":2.25}, {"label":"O", "x":9.5, "y":2.25}, {"label":"P", "x":10.5, "y":2.25}, {"label":"{", "x":11.5, "y":2.25}, {"label":"}", "x":12.5, "y":2.25}, {"label":"|", "x":13.5, "y":2.25, "w":1.5}, {"label":"Delete", "x":15.25, "y":2.25}, {"label":"End", "x":16.25, "y":2.25}, {"label":"PgDn", "x":17.25, "y":2.25}, {"label":"7", "x":18.5, "y":2.25}, {"label":"8", "x":19.5, "y":2.25}, {"label":"9", "x":20.5, "y":2.25}, {"label":"+", "x":21.5, "y":2.25, "h":2}, {"label":"Caps Lock", "x":0, "y":3.25, "w":1.75}, {"label":"A", "x":1.75, "y":3.25}, {"label":"S", "x":2.75, "y":3.25}, {"label":"D", "x":3.75, "y":3.25}, {"label":"F", "x":4.75, "y":3.25}, {"label":"G", "x":5.75, "y":3.25}, {"label":"H", "x":6.75, "y":3.25}, {"label":"J", "x":7.75, "y":3.25}, {"label":"K", "x":8.75, "y":3.25}, {"label":"L", "x":9.75, "y":3.25}, {"label":":", "x":10.75, "y":3.25}, {"label":"@", "x":11.75, "y":3.25}, {"label":"~", "x":12.75, "y":3.25}, {"label":"Enter", "x":13.75, "y":3.25, "w":1.25}, {"label":"4", "x":18.5, "y":3.25}, {"label":"5", "x":19.5, "y":3.25}, {"label":"6", "x":20.5, "y":3.25}, {"label":"Shift", "x":0, "y":4.25, "w":1.25}, {"label":"|", "x":1.25, "y":4.25}, {"label":"Z", "x":2.25, "y":4.25}, {"label":"X", "x":3.25, "y":4.25}, {"label":"C", "x":4.25, "y":4.25}, {"label":"V", "x":5.25, "y":4.25}, {"label":"B", "x":6.25, "y":4.25}, {"label":"N", "x":7.25, "y":4.25}, {"label":"M", "x":8.25, "y":4.25}, {"label":"<", "x":9.25, "y":4.25}, {"label":">", "x":10.25, "y":4.25}, {"label":"?", "x":11.25, "y":4.25}, {"label":"Shift", "x":12.25, "y":4.25, "w":2.75}, {"label":"\u2191", "x":16.25, "y":4.25}, {"label":"1", "x":18.5, "y":4.25}, {"label":"2", "x":19.5, "y":4.25}, {"label":"3", "x":20.5, "y":4.25}, {"label":"Enter", "x":21.5, "y":4.25, "h":2}, {"label":"Ctrl", "x":0, "y":5.25, "w":1.25}, {"label":"Win", "x":1.25, "y":5.25, "w":1.25}, {"label":"Alt", "x":2.5, "y":5.25, "w":1.25}, {"x":3.75, "y":5.25, "w":6.25}, {"label":"Alt", "x":10, "y":5.25, "w":1.25}, {"label":"Win", "x":11.25, "y":5.25, "w":1.25}, {"label":"Menu", "x":12.5, "y":5.25, "w":1.25}, {"label":"Ctrl", "x":13.75, "y":5.25, "w":1.25}, {"label":"\u2190", "x":15.25, "y":5.25}, {"label":"\u2193", "x":16.25, "y":5.25}, {"label":"\u2192", "x":17.25, "y":5.25}, {"label":"0", "x":18.5, "y":5.25, "w":2}, {"label":".", "x":20.5, "y":5.25}]
         },
         "LAYOUT_fullsize_iso": {
-            "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"F1", "x":2, "y":0}, {"label":"F2", "x":3, "y":0}, {"label":"F3", "x":4, "y":0}, {"label":"F4", "x":5, "y":0}, {"label":"F5", "x":6.5, "y":0}, {"label":"F6", "x":7.5, "y":0}, {"label":"F7", "x":8.5, "y":0}, {"label":"F8", "x":9.5, "y":0}, {"label":"F9", "x":11, "y":0}, {"label":"F10", "x":12, "y":0}, {"label":"F11", "x":13, "y":0}, {"label":"F12", "x":14, "y":0}, {"label":"PrtSc", "x":15.25, "y":0}, {"label":"Scroll Lock", "x":16.25, "y":0}, {"label":"Pause", "x":17.25, "y":0}, {"label":"~", "x":0, "y":1.25}, {"label":"!", "x":1, "y":1.25}, {"label":"@", "x":2, "y":1.25}, {"label":"#", "x":3, "y":1.25}, {"label":"$", "x":4, "y":1.25}, {"label":"%", "x":5, "y":1.25}, {"label":"^", "x":6, "y":1.25}, {"label":"&", "x":7, "y":1.25}, {"label":"*", "x":8, "y":1.25}, {"label":"(", "x":9, "y":1.25}, {"label":")", "x":10, "y":1.25}, {"label":"_", "x":11, "y":1.25}, {"label":"+", "x":12, "y":1.25}, {"label":"Backspace", "x":13, "y":1.25, "w":2}, {"label":"Insert", "x":15.25, "y":1.25}, {"label":"Home", "x":16.25, "y":1.25}, {"label":"PgUp", "x":17.25, "y":1.25}, {"label":"Num Lock", "x":18.5, "y":1.25}, {"label":"/", "x":19.5, "y":1.25}, {"label":"*", "x":20.5, "y":1.25}, {"label":"-", "x":21.5, "y":1.25}, {"label":"Tab", "x":0, "y":2.25, "w":1.5}, {"label":"Q", "x":1.5, "y":2.25}, {"label":"W", "x":2.5, "y":2.25}, {"label":"E", "x":3.5, "y":2.25}, {"label":"R", "x":4.5, "y":2.25}, {"label":"T", "x":5.5, "y":2.25}, {"label":"Y", "x":6.5, "y":2.25}, {"label":"U", "x":7.5, "y":2.25}, {"label":"I", "x":8.5, "y":2.25}, {"label":"O", "x":9.5, "y":2.25}, {"label":"P", "x":10.5, "y":2.25}, {"label":"{", "x":11.5, "y":2.25}, {"label":"}", "x":12.5, "y":2.25}, {"label":"Enter", "x":13.75, "y":2.25, "w":1.25, "h":2}, {"label":"Delete", "x":15.25, "y":2.25}, {"label":"End", "x":16.25, "y":2.25}, {"label":"PgDn", "x":17.25, "y":2.25}, {"label":"7", "x":18.5, "y":2.25}, {"label":"8", "x":19.5, "y":2.25}, {"label":"9", "x":20.5, "y":2.25}, {"label":"+", "x":21.5, "y":2.25, "h":2}, {"label":"Caps Lock", "x":0, "y":3.25, "w":1.75}, {"label":"A", "x":1.75, "y":3.25}, {"label":"S", "x":2.75, "y":3.25}, {"label":"D", "x":3.75, "y":3.25}, {"label":"F", "x":4.75, "y":3.25}, {"label":"G", "x":5.75, "y":3.25}, {"label":"H", "x":6.75, "y":3.25}, {"label":"J", "x":7.75, "y":3.25}, {"label":"K", "x":8.75, "y":3.25}, {"label":"L", "x":9.75, "y":3.25}, {"label":":", "x":10.75, "y":3.25}, {"label":"@", "x":11.75, "y":3.25}, {"label":"~", "x":12.75, "y":3.25}, {"label":"4", "x":18.5, "y":3.25}, {"label":"5", "x":19.5, "y":3.25}, {"label":"6", "x":20.5, "y":3.25}, {"label":"Shift", "x":0, "y":4.25, "w":1.25}, {"label":"|", "x":1.25, "y":4.25}, {"label":"Z", "x":2.25, "y":4.25}, {"label":"X", "x":3.25, "y":4.25}, {"label":"C", "x":4.25, "y":4.25}, {"label":"V", "x":5.25, "y":4.25}, {"label":"B", "x":6.25, "y":4.25}, {"label":"N", "x":7.25, "y":4.25}, {"label":"M", "x":8.25, "y":4.25}, {"label":"<", "x":9.25, "y":4.25}, {"label":">", "x":10.25, "y":4.25}, {"label":"?", "x":11.25, "y":4.25}, {"label":"Shift", "x":12.25, "y":4.25, "w":2.75}, {"label":"\u2191", "x":16.25, "y":4.25}, {"label":"1", "x":18.5, "y":4.25}, {"label":"2", "x":19.5, "y":4.25}, {"label":"3", "x":20.5, "y":4.25}, {"label":"Enter", "x":21.5, "y":4.25, "h":2}, {"label":"Ctrl", "x":0, "y":5.25, "w":1.25}, {"label":"Win", "x":1.25, "y":5.25, "w":1.25}, {"label":"Alt", "x":2.5, "y":5.25, "w":1.25}, {"x":3.75, "y":5.25, "w":6.25}, {"label":"Alt", "x":10, "y":5.25, "w":1.25}, {"label":"Win", "x":11.25, "y":5.25, "w":1.25}, {"label":"Menu", "x":12.5, "y":5.25, "w":1.25}, {"label":"Ctrl", "x":13.75, "y":5.25, "w":1.25}, {"label":"\u2190", "x":15.25, "y":5.25}, {"label":"\u2193", "x":16.25, "y":5.25}, {"label":"\u2192", "x":17.25, "y":5.25}, {"label":"0", "x":18.5, "y":5.25, "w":2}, {"label":".", "x":20.5, "y":5.25}]
+            "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"F1", "x":2, "y":0}, {"label":"F2", "x":3, "y":0}, {"label":"F3", "x":4, "y":0}, {"label":"F4", "x":5, "y":0}, {"label":"F5", "x":6.5, "y":0}, {"label":"F6", "x":7.5, "y":0}, {"label":"F7", "x":8.5, "y":0}, {"label":"F8", "x":9.5, "y":0}, {"label":"F9", "x":11, "y":0}, {"label":"F10", "x":12, "y":0}, {"label":"F11", "x":13, "y":0}, {"label":"F12", "x":14, "y":0}, {"label":"PrtSc", "x":15.25, "y":0}, {"label":"Scroll Lock", "x":16.25, "y":0}, {"label":"Pause", "x":17.25, "y":0}, {"x":18.5, "y":0}, {"x":19.5, "y":0}, {"x":20.5, "y":0}, {"x":21.5, "y":0}, {"label":"~", "x":0, "y":1.25}, {"label":"!", "x":1, "y":1.25}, {"label":"@", "x":2, "y":1.25}, {"label":"#", "x":3, "y":1.25}, {"label":"$", "x":4, "y":1.25}, {"label":"%", "x":5, "y":1.25}, {"label":"^", "x":6, "y":1.25}, {"label":"&", "x":7, "y":1.25}, {"label":"*", "x":8, "y":1.25}, {"label":"(", "x":9, "y":1.25}, {"label":")", "x":10, "y":1.25}, {"label":"_", "x":11, "y":1.25}, {"label":"+", "x":12, "y":1.25}, {"label":"Backspace", "x":13, "y":1.25, "w":2}, {"label":"Insert", "x":15.25, "y":1.25}, {"label":"Home", "x":16.25, "y":1.25}, {"label":"PgUp", "x":17.25, "y":1.25}, {"label":"Num Lock", "x":18.5, "y":1.25}, {"label":"/", "x":19.5, "y":1.25}, {"label":"*", "x":20.5, "y":1.25}, {"label":"-", "x":21.5, "y":1.25}, {"label":"Tab", "x":0, "y":2.25, "w":1.5}, {"label":"Q", "x":1.5, "y":2.25}, {"label":"W", "x":2.5, "y":2.25}, {"label":"E", "x":3.5, "y":2.25}, {"label":"R", "x":4.5, "y":2.25}, {"label":"T", "x":5.5, "y":2.25}, {"label":"Y", "x":6.5, "y":2.25}, {"label":"U", "x":7.5, "y":2.25}, {"label":"I", "x":8.5, "y":2.25}, {"label":"O", "x":9.5, "y":2.25}, {"label":"P", "x":10.5, "y":2.25}, {"label":"{", "x":11.5, "y":2.25}, {"label":"}", "x":12.5, "y":2.25}, {"label":"Enter", "x":13.75, "y":2.25, "w":1.25, "h":2}, {"label":"Delete", "x":15.25, "y":2.25}, {"label":"End", "x":16.25, "y":2.25}, {"label":"PgDn", "x":17.25, "y":2.25}, {"label":"7", "x":18.5, "y":2.25}, {"label":"8", "x":19.5, "y":2.25}, {"label":"9", "x":20.5, "y":2.25}, {"label":"+", "x":21.5, "y":2.25, "h":2}, {"label":"Caps Lock", "x":0, "y":3.25, "w":1.75}, {"label":"A", "x":1.75, "y":3.25}, {"label":"S", "x":2.75, "y":3.25}, {"label":"D", "x":3.75, "y":3.25}, {"label":"F", "x":4.75, "y":3.25}, {"label":"G", "x":5.75, "y":3.25}, {"label":"H", "x":6.75, "y":3.25}, {"label":"J", "x":7.75, "y":3.25}, {"label":"K", "x":8.75, "y":3.25}, {"label":"L", "x":9.75, "y":3.25}, {"label":":", "x":10.75, "y":3.25}, {"label":"@", "x":11.75, "y":3.25}, {"label":"~", "x":12.75, "y":3.25}, {"label":"4", "x":18.5, "y":3.25}, {"label":"5", "x":19.5, "y":3.25}, {"label":"6", "x":20.5, "y":3.25}, {"label":"Shift", "x":0, "y":4.25, "w":1.25}, {"label":"|", "x":1.25, "y":4.25}, {"label":"Z", "x":2.25, "y":4.25}, {"label":"X", "x":3.25, "y":4.25}, {"label":"C", "x":4.25, "y":4.25}, {"label":"V", "x":5.25, "y":4.25}, {"label":"B", "x":6.25, "y":4.25}, {"label":"N", "x":7.25, "y":4.25}, {"label":"M", "x":8.25, "y":4.25}, {"label":"<", "x":9.25, "y":4.25}, {"label":">", "x":10.25, "y":4.25}, {"label":"?", "x":11.25, "y":4.25}, {"label":"Shift", "x":12.25, "y":4.25, "w":2.75}, {"label":"\u2191", "x":16.25, "y":4.25}, {"label":"1", "x":18.5, "y":4.25}, {"label":"2", "x":19.5, "y":4.25}, {"label":"3", "x":20.5, "y":4.25}, {"label":"Enter", "x":21.5, "y":4.25, "h":2}, {"label":"Ctrl", "x":0, "y":5.25, "w":1.25}, {"label":"Win", "x":1.25, "y":5.25, "w":1.25}, {"label":"Alt", "x":2.5, "y":5.25, "w":1.25}, {"x":3.75, "y":5.25, "w":6.25}, {"label":"Alt", "x":10, "y":5.25, "w":1.25}, {"label":"Win", "x":11.25, "y":5.25, "w":1.25}, {"label":"Menu", "x":12.5, "y":5.25, "w":1.25}, {"label":"Ctrl", "x":13.75, "y":5.25, "w":1.25}, {"label":"\u2190", "x":15.25, "y":5.25}, {"label":"\u2193", "x":16.25, "y":5.25}, {"label":"\u2192", "x":17.25, "y":5.25}, {"label":"0", "x":18.5, "y":5.25, "w":2}, {"label":".", "x":20.5, "y":5.25}]
         },
         "LAYOUT_fullsize_ansi": {
-            "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"F1", "x":2, "y":0}, {"label":"F2", "x":3, "y":0}, {"label":"F3", "x":4, "y":0}, {"label":"F4", "x":5, "y":0}, {"label":"F5", "x":6.5, "y":0}, {"label":"F6", "x":7.5, "y":0}, {"label":"F7", "x":8.5, "y":0}, {"label":"F8", "x":9.5, "y":0}, {"label":"F9", "x":11, "y":0}, {"label":"F10", "x":12, "y":0}, {"label":"F11", "x":13, "y":0}, {"label":"F12", "x":14, "y":0}, {"label":"PrtSc", "x":15.25, "y":0}, {"label":"Scroll Lock", "x":16.25, "y":0}, {"label":"Pause", "x":17.25, "y":0}, {"label":"~", "x":0, "y":1.25}, {"label":"!", "x":1, "y":1.25}, {"label":"@", "x":2, "y":1.25}, {"label":"#", "x":3, "y":1.25}, {"label":"$", "x":4, "y":1.25}, {"label":"%", "x":5, "y":1.25}, {"label":"^", "x":6, "y":1.25}, {"label":"&", "x":7, "y":1.25}, {"label":"*", "x":8, "y":1.25}, {"label":"(", "x":9, "y":1.25}, {"label":")", "x":10, "y":1.25}, {"label":"_", "x":11, "y":1.25}, {"label":"+", "x":12, "y":1.25}, {"label":"Backspace", "x":13, "y":1.25, "w":2}, {"label":"Insert", "x":15.25, "y":1.25}, {"label":"Home", "x":16.25, "y":1.25}, {"label":"PgUp", "x":17.25, "y":1.25}, {"label":"Num Lock", "x":18.5, "y":1.25}, {"label":"/", "x":19.5, "y":1.25}, {"label":"*", "x":20.5, "y":1.25}, {"label":"-", "x":21.5, "y":1.25}, {"label":"Tab", "x":0, "y":2.25, "w":1.5}, {"label":"Q", "x":1.5, "y":2.25}, {"label":"W", "x":2.5, "y":2.25}, {"label":"E", "x":3.5, "y":2.25}, {"label":"R", "x":4.5, "y":2.25}, {"label":"T", "x":5.5, "y":2.25}, {"label":"Y", "x":6.5, "y":2.25}, {"label":"U", "x":7.5, "y":2.25}, {"label":"I", "x":8.5, "y":2.25}, {"label":"O", "x":9.5, "y":2.25}, {"label":"P", "x":10.5, "y":2.25}, {"label":"{", "x":11.5, "y":2.25}, {"label":"}", "x":12.5, "y":2.25}, {"label":"|", "x":13.5, "y":2.25, "w":1.5}, {"label":"Delete", "x":15.25, "y":2.25}, {"label":"End", "x":16.25, "y":2.25}, {"label":"PgDn", "x":17.25, "y":2.25}, {"label":"7", "x":18.5, "y":2.25}, {"label":"8", "x":19.5, "y":2.25}, {"label":"9", "x":20.5, "y":2.25}, {"label":"+", "x":21.5, "y":2.25, "h":2}, {"label":"Caps Lock", "x":0, "y":3.25, "w":1.75}, {"label":"A", "x":1.75, "y":3.25}, {"label":"S", "x":2.75, "y":3.25}, {"label":"D", "x":3.75, "y":3.25}, {"label":"F", "x":4.75, "y":3.25}, {"label":"G", "x":5.75, "y":3.25}, {"label":"H", "x":6.75, "y":3.25}, {"label":"J", "x":7.75, "y":3.25}, {"label":"K", "x":8.75, "y":3.25}, {"label":"L", "x":9.75, "y":3.25}, {"label":":", "x":10.75, "y":3.25}, {"label":"@", "x":11.75, "y":3.25}, {"label":"Enter", "x":12.75, "y":3.25, "w":2.25}, {"label":"4", "x":18.5, "y":3.25}, {"label":"5", "x":19.5, "y":3.25}, {"label":"6", "x":20.5, "y":3.25}, {"label":"Shift", "x":0, "y":4.25, "w":2.25}, {"label":"Z", "x":2.25, "y":4.25}, {"label":"X", "x":3.25, "y":4.25}, {"label":"C", "x":4.25, "y":4.25}, {"label":"V", "x":5.25, "y":4.25}, {"label":"B", "x":6.25, "y":4.25}, {"label":"N", "x":7.25, "y":4.25}, {"label":"M", "x":8.25, "y":4.25}, {"label":"<", "x":9.25, "y":4.25}, {"label":">", "x":10.25, "y":4.25}, {"label":"?", "x":11.25, "y":4.25}, {"label":"Shift", "x":12.25, "y":4.25, "w":2.75}, {"label":"\u2191", "x":16.25, "y":4.25}, {"label":"1", "x":18.5, "y":4.25}, {"label":"2", "x":19.5, "y":4.25}, {"label":"3", "x":20.5, "y":4.25}, {"label":"Enter", "x":21.5, "y":4.25, "h":2}, {"label":"Ctrl", "x":0, "y":5.25, "w":1.25}, {"label":"Win", "x":1.25, "y":5.25, "w":1.25}, {"label":"Alt", "x":2.5, "y":5.25, "w":1.25}, {"x":3.75, "y":5.25, "w":6.25}, {"label":"Alt", "x":10, "y":5.25, "w":1.25}, {"label":"Win", "x":11.25, "y":5.25, "w":1.25}, {"label":"Menu", "x":12.5, "y":5.25, "w":1.25}, {"label":"Ctrl", "x":13.75, "y":5.25, "w":1.25}, {"label":"\u2190", "x":15.25, "y":5.25}, {"label":"\u2193", "x":16.25, "y":5.25}, {"label":"\u2192", "x":17.25, "y":5.25}, {"label":"0", "x":18.5, "y":5.25, "w":2}, {"label":".", "x":20.5, "y":5.25}]
+            "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"F1", "x":2, "y":0}, {"label":"F2", "x":3, "y":0}, {"label":"F3", "x":4, "y":0}, {"label":"F4", "x":5, "y":0}, {"label":"F5", "x":6.5, "y":0}, {"label":"F6", "x":7.5, "y":0}, {"label":"F7", "x":8.5, "y":0}, {"label":"F8", "x":9.5, "y":0}, {"label":"F9", "x":11, "y":0}, {"label":"F10", "x":12, "y":0}, {"label":"F11", "x":13, "y":0}, {"label":"F12", "x":14, "y":0}, {"label":"PrtSc", "x":15.25, "y":0}, {"label":"Scroll Lock", "x":16.25, "y":0}, {"label":"Pause", "x":17.25, "y":0}, {"x":18.5, "y":0}, {"x":19.5, "y":0}, {"x":20.5, "y":0}, {"x":21.5, "y":0}, {"label":"~", "x":0, "y":1.25}, {"label":"!", "x":1, "y":1.25}, {"label":"@", "x":2, "y":1.25}, {"label":"#", "x":3, "y":1.25}, {"label":"$", "x":4, "y":1.25}, {"label":"%", "x":5, "y":1.25}, {"label":"^", "x":6, "y":1.25}, {"label":"&", "x":7, "y":1.25}, {"label":"*", "x":8, "y":1.25}, {"label":"(", "x":9, "y":1.25}, {"label":")", "x":10, "y":1.25}, {"label":"_", "x":11, "y":1.25}, {"label":"+", "x":12, "y":1.25}, {"label":"Backspace", "x":13, "y":1.25, "w":2}, {"label":"Insert", "x":15.25, "y":1.25}, {"label":"Home", "x":16.25, "y":1.25}, {"label":"PgUp", "x":17.25, "y":1.25}, {"label":"Num Lock", "x":18.5, "y":1.25}, {"label":"/", "x":19.5, "y":1.25}, {"label":"*", "x":20.5, "y":1.25}, {"label":"-", "x":21.5, "y":1.25}, {"label":"Tab", "x":0, "y":2.25, "w":1.5}, {"label":"Q", "x":1.5, "y":2.25}, {"label":"W", "x":2.5, "y":2.25}, {"label":"E", "x":3.5, "y":2.25}, {"label":"R", "x":4.5, "y":2.25}, {"label":"T", "x":5.5, "y":2.25}, {"label":"Y", "x":6.5, "y":2.25}, {"label":"U", "x":7.5, "y":2.25}, {"label":"I", "x":8.5, "y":2.25}, {"label":"O", "x":9.5, "y":2.25}, {"label":"P", "x":10.5, "y":2.25}, {"label":"{", "x":11.5, "y":2.25}, {"label":"}", "x":12.5, "y":2.25}, {"label":"|", "x":13.5, "y":2.25, "w":1.5}, {"label":"Delete", "x":15.25, "y":2.25}, {"label":"End", "x":16.25, "y":2.25}, {"label":"PgDn", "x":17.25, "y":2.25}, {"label":"7", "x":18.5, "y":2.25}, {"label":"8", "x":19.5, "y":2.25}, {"label":"9", "x":20.5, "y":2.25}, {"label":"+", "x":21.5, "y":2.25, "h":2}, {"label":"Caps Lock", "x":0, "y":3.25, "w":1.75}, {"label":"A", "x":1.75, "y":3.25}, {"label":"S", "x":2.75, "y":3.25}, {"label":"D", "x":3.75, "y":3.25}, {"label":"F", "x":4.75, "y":3.25}, {"label":"G", "x":5.75, "y":3.25}, {"label":"H", "x":6.75, "y":3.25}, {"label":"J", "x":7.75, "y":3.25}, {"label":"K", "x":8.75, "y":3.25}, {"label":"L", "x":9.75, "y":3.25}, {"label":":", "x":10.75, "y":3.25}, {"label":"\"", "x":11.75, "y":3.25}, {"label":"Enter", "x":12.75, "y":3.25, "w":2.25}, {"label":"4", "x":18.5, "y":3.25}, {"label":"5", "x":19.5, "y":3.25}, {"label":"6", "x":20.5, "y":3.25}, {"label":"Shift", "x":0, "y":4.25, "w":2.25}, {"label":"Z", "x":2.25, "y":4.25}, {"label":"X", "x":3.25, "y":4.25}, {"label":"C", "x":4.25, "y":4.25}, {"label":"V", "x":5.25, "y":4.25}, {"label":"B", "x":6.25, "y":4.25}, {"label":"N", "x":7.25, "y":4.25}, {"label":"M", "x":8.25, "y":4.25}, {"label":"<", "x":9.25, "y":4.25}, {"label":">", "x":10.25, "y":4.25}, {"label":"?", "x":11.25, "y":4.25}, {"label":"Shift", "x":12.25, "y":4.25, "w":2.75}, {"label":"\u2191", "x":16.25, "y":4.25}, {"label":"1", "x":18.5, "y":4.25}, {"label":"2", "x":19.5, "y":4.25}, {"label":"3", "x":20.5, "y":4.25}, {"label":"Enter", "x":21.5, "y":4.25, "h":2}, {"label":"Ctrl", "x":0, "y":5.25, "w":1.25}, {"label":"Win", "x":1.25, "y":5.25, "w":1.25}, {"label":"Alt", "x":2.5, "y":5.25, "w":1.25}, {"x":3.75, "y":5.25, "w":6.25}, {"label":"Alt", "x":10, "y":5.25, "w":1.25}, {"label":"Win", "x":11.25, "y":5.25, "w":1.25}, {"label":"Menu", "x":12.5, "y":5.25, "w":1.25}, {"label":"Ctrl", "x":13.75, "y":5.25, "w":1.25}, {"label":"\u2190", "x":15.25, "y":5.25}, {"label":"\u2193", "x":16.25, "y":5.25}, {"label":"\u2192", "x":17.25, "y":5.25}, {"label":"0", "x":18.5, "y":5.25, "w":2}, {"label":".", "x":20.5, "y":5.25}]
         }
     }
 }

keyboards/handwired/hnah108/keymaps/default/keymap.c

@@ -44,17 +44,20 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 };
 
 void encoder_update_user(uint8_t index, bool clockwise) {
-  if (IS_LAYER_ON(_FN)) { /* First encoder */
+  if (index == 0) {
+    if (IS_LAYER_ON(_FN)) { 
     if (clockwise) {
-      rgb_matrix_step();
+            tap_code(KC_BRIU);
     } else {
-      rgb_matrix_step_reverse();	
+            tap_code(KC_BRID);
     }
   } else {
     if (clockwise) {
-      rgb_matrix_increase_speed();
+            tap_code(KC_VOLU);
+
     } else {
-      rgb_matrix_decrease_speed();
+            tap_code(KC_VOLD);
+      }
     }
   }
 }