# Ender 5 Pro

## Setup

Firmware:

[Creality Board](Firmware/Ender-5%20pro%204.2.7mainboard%EF%BC%8832bit%EF%BC%89/Marlin2.0.1%20%20BLtouch%20V1.1.1%20Non-adapter%20board%20firmwareTMC2225/Ender-5%20Pro-%20Marlin2.0.1%20-%20V1.1.1%20-%20BLTouch%20-%20TMC2235.bin?fileId=72632)

[V.4.2.7](Firmware/Ender-5%20pro%204.2.7mainboard%EF%BC%8832bit%EF%BC%89/Marlin2.0.1%20%20BLtouch%20V1.1.1%20Non-adapter%20board%20firmwareTMC2225/Ender-5%20Pro-%20Marlin2.0.1%20-%20V1.1.1%20-%20BLTouch%20-%20TMC2235.bin?fileId=72632)

Extruder steps/mm: 147.5

BL Touch Z-Height Offset: -2.4

Print area: 220 x 220 x 300 mm

Use Ender-5 base when setting up in Cura

Start G-Code:

```text
; Ender 5 Pro Custom Start G-code
; Script based on an original created by tjjfvi (https://github.com/tjjfvi)
; An up-to-date version of the tjjfvi's original script can be found
; here:  https://csi.t6.fyi/
; Note - This script will only work in Cura V4.2 and above!
; --- Global Settings
; layer_height = {layer_height}
; smooth_spiralized_contours = {smooth_spiralized_contours}
; magic_mesh_surface_mode = {magic_mesh_surface_mode}
; machine_extruder_count = {machine_extruder_count}
; --- Single Extruder Settings
; speed_z_hop = {speed_z_hop}
; retraction_amount = {retraction_amount}
; retraction_hop = {retraction_hop}
; retraction_hop_enabled = {retraction_hop_enabled}
; retraction_enable = {retraction_enable}
; retraction_speed = {retraction_speed}
; retraction_retract_speed = {retraction_retract_speed}
; retraction_prime_speed = {retraction_prime_speed}
; speed_travel = {speed_travel}

G92 E0 ; Reset Extruder
G28 ; Home all axes
G29 ; Bed leveling
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed
G1 X0.1 Y20 Z0.3 F5000.0 ; Move to start position
G1 X0.1 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line
G1 X0.4 Y200.0 Z0.3 F5000.0 ; Move to side a little
G1 X0.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line
G92 E0 ; Reset Extruder
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed
G1 X5 Y20 Z0.3 F5000.0 ; Move over to prevent blob squish
```

End G-Code:

```text
G91 ;Relative positioning
G1 E-10 F2700 ;Retract a bit
G1 E-2 Z0.2 F2400 ;Retract and raise Z
G1 X5 Y5 F3000 ;Wipe out
G1 Z10 ;Raise Z more
G90 ;Absolute positioning

G1 X0 Y0 ;Present print
M106 S0 ;Turn-off fan
M104 S0 ;Turn-off hotend
M140 S0 ;Turn-off bed

M84 X Y E ;Disable all steppers but Z
```

## Cura Plugins

1. OctoPrint Connection by filedOfView

## Cura Settings

1. Preferences -> Setting Visibility -> Check all
2. Printers -> Connect OctoPrint -> printer should show up automatically

## Print Settings

1. 2mm retraction distance (with micro-swiss direct drive hotend)
2. 25mm/s retraction speed (with micro-swiss direct drive hotend)
3. Cubic Infill

## Filament

### Overture PETG

* 230C Nozzle
* 80C Bed
* 30mm travel
* 15mm move

### Change filament

1. Pause at height
2. Set layer number
3. Use Repetier/OctoPrint method
4. Park print head at 0,0
5. Set head z to 0mm